Yaesu FT-847 Operating Manual page 27

Front Panel Controls & Switches
(32) Keypad
The keypad is used for direct frequency entry during
VFO operation. Secondary functions allow control of
certain repeater, scanning, and frequency navigation
functions.
(33) SHIFT Control
This control is used to adjust the receiver's IF S
feature, which tunes the 455 kHz IF relative to the
center frequency of the selected IF filter (in all modes
except FM). The default position of this control is 12
o'clock, and an adjustment range of about ±1.2 kHz is
provided (the pitch of the incoming signals will not
change, however).
(34) DIG. FIL Switch
Pressing this switch activates the receiver's DSP fil-
ters. When the DSP is activated, the "DIG.FIL " icon
will appear on the display panel.
(35) D F
IGITAL IL
(LOW CUT/HIGH CUT Controls)
These controls adjust the passband cutoff frequencies
of the receiver's HIGH CUT and LOW CUT DSP
filters in the SSB, AM, and FM modes. The inner con-
trol adjusts the L -C
OW UT
control adjusts the H -C
IGH
(36) NOTCH Switch
This is the O /O switch for the beat-canceling DSP
N FF
N filter.
OTCH
(37) NR Switch
This is the O /O switch for the DSP N
N FF
filter. The level of DSP Noise Reduction is set
TION
via Menu #11 (see page 85).
(38) CLAR Switch
Pressing this switch activates the RX C
("RIT"), which provides offset tuning from the Main
VFO frequency. When this feature is enabled, the
"C L A R " icon will appear on the display panel. The
SUB-TUNE knob is used for Clarifier adjustment, and
the available offset range is ±9.99 kHz.
FT-847 O
PERATING
characteristics, while the outer
characteristics.
UT
R
OISE EDUC
LARIFIER
M
ANUAL
(39) SUB-TUNE Knob
This knob is the tuning dial which controls the fre-
quency of the Sub VFO. Clockwise rotation of the dial
increases the frequency, while counter-clockwise ro-
tation decreases the frequency.
The tuning steps are defined by the setting of Menu
#2, which also sets the steps for the Main Tuning Dial.
HIFT
The default tuning steps are shown below:
Mode
SSB/CW 0.1, 1, 10 Hz
AM/FM
(40) MENU Switch
Pressing this switch momentarily activates the "M
mode, which allows customization of many aspects of
transceiver configuration.
(41) MEM/VFO CH Knob
When the VFO mode is active, this detented knob be-
comes a "channelized" tuning control, which allows
quick navigation up and down the band.
This knob selects the Memory Channel when the
Memory mode is active.
The tuning steps for the MEM/VFO CH knob (when
operating in the "VFO" mode) may be set via the Menu
system. The default steps are:
Operating
Mode
SSB/CW
-
A M
FM
Ú: Depends on transceiver version (USA, European, etc.)
These steps may be set individually for the HF, 50
MHz, 144 MHz, and 430 MHz bands; see page 34 for
details.
(42) QMB RCL Switch
This switch is used for one-touch recall of the Quick
Memory Bank memory.
(43) QMB STO Switch
This switch is used for storing a Main VFO frequency
into the QMB memory register.
Available Steps
N F
ORMAL A S T
1, 10, 100 Hz
10 Hz 100 Hz
HF Bands VHF Bands
2.5 kHz 2.5 kHz
5 kHz 5 kHz
Ú
5 kHz
Default
Step
1 Hz/10 Hz
10 Hz/100 Hz
"
ENU
UHF Bands
2.5 kHz
5 kHz
Ú
25