About The Transverter Output Terminal - Yaesu FT DX 9000 CONTEST Operation Manual

You may connect an after-market transverter to the rear panel's TRV (Transverter) jack. The output, at 28 MHz, is approxi-
mately –20 dBm (0.01 mW) at 50 Ohms.
Pin 2 (TX GND) of BAND DATA 1Jack or
Pin 2 (TX GND) of BAND DATA 2 Jack
S
ETUP
1. Press the [ MNU ] key to enter the Menu mode (the LCD
will change to Menu display).
2. Rotate the [ Main Tuning Dial ] knob to choose Menu
item "TUNING 145 MY BAND."
3. Rotate the [ CLAR/VFO-B ] knob to find the Menu
parameter "TRV OFF" (this is the factory default set-
ting).
4. Press the [ ENT ] key to change the parameter to "TRV
ON" (this will add this condition to your "My Band"
list; see page 48).
5. Press and hold in the [ MNU ] key for at least two sec-
onds to save the new setting and exit to normal opera-
tion.
You may set up the frequency display so that it shows the actual band on which your transverter is operating
(instead of the "IF" used by the transverter, which is the 28 MHz band on your FT
Example: Setting Up the FT
1. Connect the 144 MHz transverter to the trans-
ceiver.
2. Use the Menu mode to confirm that Menu item
"GENERAL 042 TRV OFFSET" is set to "44"
(the factory default setting).
3. Press the [ BAND/MHz ] key momentarily, then
rotate the [ CLAR/VFO-B ] knob so as to se-
lect "44.000000" on the display.
4. Press and hold in the [ MNU ] key for at least
two seconds to save the new setting and exit.
FT 9000 C O
DX ONTEST
A A A A A
BOUT THE BOUT BOUT
BOUT BOUT
TRV Jack
Setting the Transverter Frequency Offset
9000 Contest Display for Use with a 144 MHz Transverter
DX
M
PERATION ANUAL
T T T T T
THE THE THE RANSVER RANSVER RANSVER TER TER TER TER
THE RANSVER RANSVER TER
Coaxial Cable (50 Ohm)
同軸ケーブル（ 50 Ω）
O
1. Set up the frequency offset for transverter use, as de-
scribed previously.
2. Rotate the [ Main Tuning Dial ] knob to set the de-
sired operating frequency. Operation is basically un-
changed from normal transceiver operation.
When the "TRV" mode is turned on, power output
will not be allowed to pass to the [ ANT1 ] ~ [ ANT4 ]
main antenna jacks. So one of these may be con-
nected to your transverter's RX jack. Just be cer-
tain to disconnect the transverter when returning
to HF operation, as the selected Antenna jack will
now be capable of passing RF power.
The "100 MHz" digit of the frequency is not displayed,
so when you are operating on 2 meters and see "45
MHz" on the frequency readout, this indicates "145
MHz" instead.
A
DVICE
With the setup described above, tuning the operating
range 28-29 MHz will correspond to an actual operat-
ing frequency of 144-145 MHz, with "44-45" being
displayed on the front panel of the transceiver.
O O O O O T T T T T
UTPUT UTPUT UTPUT ERMIN ERMIN AL AL AL AL AL ERMIN
UTPUT UTPUT ERMIN ERMIN
V/U ANT
Transceiver
RF IN TX GND
PERATION
A
DVICE
9000Contest).
DX
Page 125