Yaesu FT DX 9000 CONTEST Operation Manual page 151

TX AUDIO G
170. P-PRMTRC EQ3-FREQ
Function: Selects the center frequency of the high
range for the parametric microphone equalizer of the
Speech Processor.
Available Values: OFF/1500 ~ 3200 Hz (100 Hz/
step)
Default Setting: 2100 Hz
OFF: The equalizer gain and Q-factor are set
to factory defaults (flat).
1500 ~ 3200: You may adjust the equalizer gain and
Q-factor at this selected audio fre-
quency via menu items 171:
PRMTRC EQ3-LEVEL PRMTRC EQ3-LEVEL PRMTRC EQ3-LEVEL PRMTRC EQ3-LEVEL PRMTRC EQ3-LEVEL
PRMTRC EQ3-BWTH PRMTRC EQ3-BWTH PRMTRC EQ3-BWTH
PRMTRC EQ3-BWTH PRMTRC EQ3-BWTH
171. P-PRMTRC EQ3-LEVEL
Function: Adjusts the equalizer gain of the high range
for the parametric microphone equalizer of the
Speech Processor.
Available Values: –20 ~ +10
Default Setting: 0
172. P-PRMTRC EQ3-BWTH
Function: Adjusts the Q-factor of the high range for
the parametric microphone equalizer of the Speech
Processor.
Available Values: 1 ~ 10
Default Setting: 1
FT 9000 C O
DX ONTEST
ROUP
R- R- R- R- R-
and 172:
R- R- R- R- R-
.
M
PERATION ANUAL
TX GNRL G
173. TX MAX POWER
Function: Selects a maximum output power limit.
Available Values: 200/100/50/10 W
Default Setting: 200 W
174. TX PWR CONTROL
Function: Configures the RF PWR knob.
Available Values: ALL MODE/CARRIER
Default Setting: ALL MODE
ALL MODE: The [ RF PWR ] knob is enabled on all
modes.
CARRIER: The [ RF PWR ] knob is enabled in all
modes except SSB. In this configura-
tion, the SSB output power will be set
to maximum, regardless of the [ RF
PWR ] knob's position.
175. EXT AMP TX-GND
Function: Enables/Disables the TX GND jack on the
rear panel.
Available Values: ENABLE/DISABLE
Default Setting: DISABLE
176. EXT AMP TUNING PWR
Function: Selects a maximum output power limit for
driving the input circuit of an external linear RF am-
plifier while tuning (while using the Remote Control
function of the linear RF amplifier).
Available Values: 200/100/50/10 W
Default Setting: 100 W
177. FULL DUPLEX
Function: Enables/Disables Full Duplex operation.
Available Values: SIMP/DUP
Default Setting: SIMP
E : When the optional Dual Receive Unit
XPLANATION
(RXU-9000) is installed, engaging "DUP" allows you
to listen on the Sub (VFO-B) receiver while simulta-
neously transmitting on the Main (VFO-A) frequency
(on a different band) in a "Full Duplex" mode.
178. VOX SELECT
Function: Selects the audio input source for trigger-
ing TX during VOX operation.
Available Values: MIC/DATA
Default Setting: MIC
MIC: The VOX function will be activated by micro-
phone audio input.
DATA: The VOX function will be activated by data
audio input.
179. EMERGENCY FREQ TX
Function: Enables Tx/Rx operation on the Alaska
Emergency Channel, 5167.5 kHz.
Available Values: DISABLE/ENABLE
Default Setting: DISABLE
When this Menu Item is set to "ENABLE," the spot
frequency of 5167.5 kHz will be enabled. The Alaska
Emergency Channel will be found between the
Memory channels "P-1" and "01 (or 1-01)."
M M M M M M M M M M
ENU ENU ENU ODE ODE ODE
ENU ENU ODE ODE
ROUP
Page 149