Utilities - DigiTech GNX2 User Manual

Grn GAIN
(Green Gain) - Controls the Amp Gain for the Green Channel.
Gnr LEVL
(Green Level) - Controls the Volume of the Green Channel.
Red GAIN
(Red Gain) - Controls the Amp Gain for the Red Channel.
Red LEVL (Red Level) - Controls the Volume of the Red Channel.
GATTHRes
(Gate Threshold) - Controls the Noise Gate's Threshold.
GATAtTaK
(Gate Attack) - Controls the Noise Gate's Attack time.
PLKSNS
(Gate Pluck) - Controls the Noise Gate's Pluck Sensitivity.
Modulation Effects Parameters
Active Effect
Chorus
Flanger
Phaser
Triggered Flanger
Triggered Phaser
Tremolo
Panner
Vibrato
Rotary Speaker
Auto Ya™
YaYa™
SynthTalk
Envelope Filter
Detune
Pitch Shift
DLY FdBK
(Delay Feedback) - Controls the amount of Delay Feedback.
DUKTHRes
(Delay Threshold) - Controls the Ducker Threshold for the Delay.
DUk AtTN (Ducker Attenuation) - Controls the attenuation level applied to the Delay signal when the
Ducker Threshold is exceeded.
DLY LeVL
(Delay Level) - Controls the Mix Level of the selected Delay Type.
DLY BAL
(Delay Balance) - Controls the left/right balance of the selected Delay Type.
RVB PRE
(Reverb Predelay) - Controls the Reverbs Predelay time.
RVBdecay (Reverb Decay) - Controls the Reverbs Decay time.
RVB LeVL
(Reverb Level) - Controls the Reverbs Mix Level.
RVB BAL
(Reverb Balance) - Controls the left/right balance of the selected Reverb Type.
VOL PRE
(Volume Pre) - Controls the Volume after the Amp Modeling but before the Effects.
VOL PoST
(Volume Post) - Controls the Volume at the end of the Effects chain.
LFo1 SPD (LFO 1 Speed) - Controls the modulation speed of Expression LFO 1.
LFo2 SPD
(LFO 2 Speed) - Controls the modulation speed of Expression LFO 2.

Utilities

The Utility section contains all of the menus for assigning global functions to the GNX2. Global functions
affect the GNX2 in its entirety rather than on a per preset basis.The Utility menus include: Mono/Stereo
Output,Target System Setup,Volume Pedal Update,V-Switch Threshold, Expression Pedal Calibration, Dry
Track Enable, Bank Naming, MIDI Channel, MIDI Sysex Dumps, Amp Dumps, MIDI Mapping, MIDI Merge, and
Factory Reset.To enter the Utility section, press the Utility button. Once in the Utility menu, the Rhythm
button selects the next menu (scrolls to the right), and the FX Mode button selects the previous menu
(scrolls to the left). Each of these Utility menus is described in more detail in the following pages.
Speed Depth
Speed Depth
Speed Depth
Speed Senstv
Speed Senstv
Speed Depth
Speed Depth
Speed Depth
Speed Depth
Speed Depth
YA PDL Depth
Attack Release Vox
Senstvty Range
Amount MOD Bal MOD LVL
SHIFT MOD Bal MOD LVL
PreDly MOD Bal
Regen MOD Bal
Regen MOD Bal
LFO St MOD MIX
LFO St MOD MIX
Doppler crosover MODBAL
RANGE MOD Bal
RANGE MOD Bal
MOD Bal
MOD Bal MOD MIX
Other Functions
MOD LVL
MOD MIX
MOD MIX
MOD MIX
MOD MIX
MOD MIX
Senstvty
39