Using Multi Operations; Using System Off; Controls For Tvs - Pioneer Elite VSX-90TXV Operating Instructions Manual

Controlling the rest of your system
8 Repeat steps 5–7 to program a sequence of up to
five commands.
When you're finished, use / to select EDITEXIT
9
from the menu and press ENTER.
You will return to the remote control SETUP menu. Select
* EXIT * again to exit.

Using multi operations

You can start multi operations with the receiver switched
on, or in standby.
AUDIO SUBTITLE
DISP
THX STANDARD
MULTI OPE AUTO SURR
SHIFT EFFECT/CH SEL
RECEIVER
1 Press MULTI OPE.
MULTI OP flashes in the display.
2 Press an input source button that has been set up
with a multi operation.
The receiver switches on (if it was in standby) and the
programmed multi operation is performed automatically.

Using System off

SYSTEM OFF
RECEIVER INPUT
SOURCE
SELECT
XM RADIO SIRIUS DVR 2
DVD TV DVR 1 TV CTRL
1 Press MULTI OPE.
MULTI OP flashes in the display.
Press  SOURCE.
2
The command sequence you programmed will run, then
all Pioneer components will switch off
receiver.

Controls for TVs

This remote control can control components after
entering the proper codes or teaching the receiver the
commands (see Setting the remote to control other
components on page 61 for more on this). Use the input
source buttons to select the component.
Note
1 In order to avoid accidently switching off a DVD recorder that is currently recording, no DVD recorder power off codes are sent.
HDD DVD
CH CH
PHOTO
STEREO/
ADV.SURR
F.S.SURR
ACOUSTIC EQ SIGNAL SEL
LEVEL
AUDIO SUBTITLE HDD DVD
DISP CH CH
PHOTO
STEREO/
THX STANDARD ADV.SURR
F.S.SURR
AUTO SURR
MULTI OPE ACOUSTIC EQ SIGNAL SEL
SHIFT EFFECT/CH SEL LEVEL
RECEIVER
1
, followed by this
• The TV CONTROL buttons on the remote control are
dedicated to control the TV assigned to the TV CTRL
button. If you have two TVs, assign the main TV to the
TV CTRL button.
Button(s) Function
TV Press to switch the component
assigned to the TV CONT
button on or off.
INPUT Switches the TV input. (Not
SELECT
possible with all models.)
TV CH +/–
Selects channels.
TV VOL +/– Adjust the TV volume.
SOURCE
Switches the DTV on or off.
Switches the TV or CATV between
standby and on.

Switches the DTV on or off.

Press to get information on DTV
programs.

Use to choose the BLUE
commands on a DTV menu.

Use to choose the YELLOW
commands on a DTV menu.

Use to choose the GREEN
commands on a DTV menu.

Use to choose the RED
commands on a DTV menu.
AUDIO / DISP Use to switch DTV audio tracks.
SUBTITLE Use to return to the previously
selected channel.
GUIDE Use as the GUIDE button for
navigating.
ANT Use to select the VHF/UHF
antennas or Cable TV.
RETURN Use to select RETURN or EXIT.
Number Use to select a specific TV
buttons channel.
+10 button Use to add a decimal point when
selecting a specific TV channel.
ENTER/ Use to enter a channel.
DISC
MENU Select different menus from the
DTV functions.
Select the menu screen.
///
Press to select or adjust and
& ENTER
navigate items on the menu
screen.
11
Components
Cable TV/Satellite
TV/TV/DTV
Cable TV/Satellite
TV/TV/DTV
Cable TV/Satellite
TV/TV/DTV
Cable TV/Satellite
TV/TV/DTV
DTV
Cable TV/Satellite
TV/TV
DTV
DTV
DTV
DTV
DTV
DTV
DTV
Cable TV/Satellite
TV/TV/DTV
Cable TV/Satellite
TV/TV/DTV
Cable TV/TV
DTV
Cable TV/Satellite
TV/TV/DTV
DTV
Cable TV/Satellite
TV/TV/DTV
DTV
Cable TV/Satellite
TV/TV
Cable TV/Satellite
TV/TV/DTV
63
En