Table of Contents
Advertisement
Other Settings
Chapter 9:
Other Settings
The Input Assign menu
You only need to make settings in the Input Assign menu
if you didn't hook up your digital equipment according to
the default settings for the digital inputs, or if you have
connected equipment using component video cables.
1
Press RECEIVER on the remote control, then press
the SETUP button.
An on-screen display (OSD) appears on your TV. Use /
// and ENTER to navigate through the screens
and select menu items. Press RETURN to confirm and
exit the current menu.
2
Select 'Input Assign' from the System Setup menu.
System Setup
1.Surr Back System
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
: Exit
Assigning the digital inputs
• Default settings:
Coaxial - 1 – DVD/LD
Coaxial - 2 – DVR 2
Optical - 1 – DVR 1
Optical - 2 – TV/SAT
Optical - 3 – CD
You only need to do this if you didn't hook up your digital
equipment according to the default settings for the
digital inputs (see above). This setting tells the receiver
what digital equipment is hooked up to which terminal so
the buttons on the remote correspond to what you have
hooked up.
1
Select 'Digital Input' from the Input Assign menu.
5.Input Assign
a.Digital Input
b.Component Input
c.HDMI Input
:Return
2
Select the number of the digital input to which
you've connected the digital component.
The numbers correspond with the numbers beside the
inputs on the back of the receiver.
3
Select the component that corresponds with the
one you connected to that input.
Select between DVD/LD, TV/SAT, CD, CD-R, DVR 1,
DVR 2 or OFF.
5.Input Assign
a.Digital Input
b.Component Input
c.HDMI Input
:Return
5a.Digital Input Setup
Coaxial - 1
DVD/LD
Coaxial - 2
[ DVR 2 ]
Optical - 1
[ DVR 1 ]
Optical - 2
[ TV/SAT ]
Optical - 3
[
CD
]
:Finish
• Use / and ENTER to do this.
• If you assign a digital input to a certain function (for
example, DVD/LD) then any digital inputs previously
assigned to that function will automatically be
switched off.
4
When you're finished, press RETURN.
You return to the Input Assign menu.
Assigning the component video inputs
• Default settings:
Component - 1 – OFF
Component - 2 – OFF
Component - 3 – OFF
If you used component video cords to connect your video
equipment you must tell the receiver which device it is, or
else you may see the S-video or composite video input
instead of the component video signal. For more on this,
see Using the component video jacks on page 14.
1
Select 'Component Input' from the Input Assign
menu.
5. Input Assign
a.Digital Input
b.Component Input
c.HDMI Input
:Return
2
Select the number of the component video input to
which you've connected your video component.
The numbers correspond with the numbers beside the
inputs on the back of the receiver.
3
Select the component that corresponds with the
one you connected to that input.
Select between DVD/LD, TV/SAT, DVR 1, DVR 2 or OFF.
• Use / and ENTER to do this.
• Make sure you have connected the audio from the
component to the corresponding inputs on the rear
of the receiver.
• If you connect any source component to the receiver
using a component video input, you should also have
your TV connected to this receiver's component video
MONITOR output (downconverting component video
is not possible after assigning an input).
4
When you're finished, press RETURN.
You return to the Input Assign menu.
5b.Component Input
Component - 1
OFF
Component - 2
[
OFF
]
Component - 3
[
OFF
]
:Finish
09
55
En
Hide quick links:
Advertisement
Table of Contents
