Crossover Network; Channel Level - Pioneer Elite VSX-90TXV Operating Instructions Manual

The System Setup menu
Tip
• If you have a subwoofer and like lots of bass, it may
seem logical to select LARGE for your front speakers
and PLUS for the subwoofer. This may not, however,
yield the best bass results. Depending on the speaker
placement of your room you may actually experience
a decrease in the amount of bass due to low
frequency cancellations. In this case, try changing
the position or direction of speakers. If you can't get
good results, listen to the bass response with it set to
PLUS and YES or the front speakers set to LARGE and
SMALL alternatively and let your ears judge which
sounds best. If you're having problems, the easiest
option is to route all the bass sounds to the
subwoofer by selecting SMALL for the front speakers.

Crossover Network

• Default setting: 80Hz
This setting decides the cutoff between bass sounds
playing back from the speakers selected as LARGE, or
the subwoofer, and bass sounds playing back from those
selected as SMALL. It also decides where the cutoff will
be for bass sounds in the LFE channel.
1 Select 'Crossover Network' from the Manual SP
Setup menu.
4.Manual SP Setup
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
e.THX Audio Setting
f.THX Speaker Setup
:Return
2 Choose the frequency cutoff point.
Frequencies below the cutoff point will be sent to the
subwoofer (or LARGE speakers).
3 When you're finished, press RETURN.
You return to the Manual SP Setup menu.

Channel Level

Using the channel level settings, you can adjust the
overall balance of your speaker system, an important
factor when setting up a home theater system.
Note
1 • For more on selecting the speaker sizes, see Speaker Setting above.
• If you're using a THX speaker setup, confirm that the crossover frequency is set to 80Hz.
2 • If you are using a Sound Pressure Level (SPL) meter, take the readings from your main listening position and adjust the level of each speaker to 75 dB
SPL (C-weighting/slow reading).
• The subwoofer test tone is output at low volumes. You may need to adjust the level after testing with an actual soundtrack.
1
4b.Crossover Network
Frequency 80Hz
( THX : 80Hz )
:Finish
1 Select 'Channel Level' from the Manual SP Setup
menu.
4.Manual SP Setup
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
e.THX Audio Setting
f.THX Speaker Setup
:Return
2 Select a setup option.
• Manual – Move the test tone manually from speaker
to speaker and adjust individual channel levels.
• Auto – Adjust channel levels as the test tone moves
from speaker to speaker automatically.
3 Confirm your selected setup option.
The test tones will start after you press ENTER.
4c.Channel Level
Test Tone
Please Wait . . .
Caution!
Loud test tones
will be output.
Adjust the level of each channel using /.
4
If you selected Manual, use / to switch speakers. The
Auto setup will output test tones in the order shown on-
screen:
4c.Channel Level
L 0.0dB
C [ 0.0dB ]
R [ 0.0dB ]
SR [ 0.0dB ]
SBR [ 0.0dB ]
SBL [ 0.0dB ]
SL [ 0.0dB ]
SW [ 0.0dB ]
Adjust the level of each speaker as the test tone is
2
emitted.
5 When you're finished, press RETURN.
You return to the Manual SP Setup menu.
Tip
• You can change the channel levels at any time by
using EFFECT/CH SEL and +/– on the remote control.
You can set two channel levels: one for MULTI CH IN
and one for the listening modes.
4c.Channel Level
Test Tone Manual
ENTER:Next :Cancel
[ Manual ]
20
:Cancel
:Finish
07
41
En