Table of Contents
Advertisement
Other connections
08
Connecting an IR receiver
If you keep your stereo components in a closed cabinet or
shelving unit, you can use an optional IR receiver (such
as a Niles or Xantech unit) to control your system instead
of the remote sensor on the front panel of this receiver.
MULTI-ZONE & SOURCE ZONE 2
OUT
IR
COMPONENT VIDEO
CONTROL
OUT
1
Connect the IR receiver sensor to the MULTI-ZONE &
SOURCE IR IN jack on the rear of this receiver.
2
Connect the IR IN jack of another component to the
MULTI-ZONE & SOURCE IR OUT jack on the rear of this
receiver to link it to the IR receiver.
Please see the manual supplied with your IR receiver for
the type of cable necessary for the connection.
• If you want to link a Pioneer component to the IR
receiver, see Operating other Pioneer components
with this unit's sensor on page 65 to connect to the
CONTROL jacks instead of the IR OUT jack.
Note
1 • Remote operation may not be possible if direct light from a strong fluorescent lamp is shining on the IR receiver remote sensor window.
• Note that other manufacturers may not use the IR terminology. Refer to the manual that came with your component to check for IR compatibility.
• If using two remote controls (at the same time), the IR receiver's remote sensor takes priority over the remote sensor on the front panel.
52
En
Closet or shelving unit
Non-Pioneer
IR
component
IN
Pioneer
CONTROL
component
IN
OUT
ANTENNA
IN
MULTI-ZONE & SOURCE ZONE 2
ANTENNA
OPTICAL
DIGITAL
OUT
IN
IR
OUT
IN
AM LOOP
1
COMPONENT VIDEO
CENTER
(DVD/LD)
IN
1
L
Y
P
B
P
R
Y
P
B
P
R
(DVR/
IN
VCR1)
OUT
1
IN 2
IN
(TV/SAT)
2
IN
IN
(TV/SAT)
2
3
Y
P
P
Y
P
P
IN 3
B
R
B
R
R
SUB
ASSIGNABLE
1
3
(CD)
FRONT
WOOFER
OUT
ASSIGNABLE
1
3
S-VIDEO
iPod
HDMI
ASSIG-
NABLE
IN
IN
OUT
IN
OUT
IN
CONTROL
iPod
1
2
OUT
VIDEO
XM
IN
IN
IN
IN
AUDIO
IN
OUT
IN
IN
IN
OUT
IN
OUT
IN
L
IN 1
(DVD/LD)
R
IN 2
(DVR/VCR2)
CD
CD-R/TAPE/MD
DVD/LD
TV/SAT
DVR/VCR1
DVR/VCR2
COAXIAL
ASSIGNABLE
1
2
IR receiver
Switching components on and off using
the 12 volt trigger
You can connect a component in your system (such as a
screen or projector) to this receiver so that it switches on
1
or off using a 12 volt trigger when you select an input
function. However, you must specify which input
functions switch on the trigger using the 12 Volt Trigger
setup on page 58. Note that this will only work with
components that have a standby mode.
IN
1
(DVD/LD)
IN
2
(TV/SAT)
PRE OUT
(Single)
L
L
OUT
R
HDMI
R
SUR-
SURROUND BACK
ROUND
ASSIG-
12V
SIRIUS
NABLE
TRIGGER
IN
1
2
(DC OUT 12V/
MONITOR
MULTI-ZONE
50mA MAX)
XM
OUT
ZONE 2
& SOURCE
MONITOR
L
OUT
R
IN
L
CENTER
L
L
•
Connect the 12 V TRIGGER jack of this receiver to
R
R
R
FRONT
SUB
SUR-
SURROUND
WOOFER
ROUND
BACK
the 12 V trigger of another component.
MULTI CH IN
Use a cable with a mono mini-plug on each end for the
connection.
• The trigger maximum power is DC OUT 12 V/50 mA.
After you've specified the input functions that will switch
on the trigger, you'll be able to switch the component on
or off just by pressing the input function(s) you've set in
12 Volt Trigger setup on page 58.
12V
TRIGGER
ANTENNA
MULTI-ZONE & SOURCE ZONE 2
OPTICAL
DIGITAL
OUT
IN
IR
OUT
AM LOOP
COMPONENT VIDEO
L
IN
1
Y
P
P
Y
P
P
B
R
B
R
(DVR/
IN
OUT
VCR1)
1
IN 2
(TV/SAT)
IN
IN
2
3
Y
P
P
Y
P
P
IN 3
B
R
B
R
R
ASSIGNABLE
1
3
(CD)
FRONT
ASSIGNABLE
1
3
S-VIDEO
IN
IN
OUT
IN
OUT
IN
CONTROL
iPod
OUT
VIDEO
IN
IN
PRE OUT
CENTER
(Single)
L
L
R
R
SUB
SUR-
SURROUND BACK
WOOFER
ROUND
12V
SIRIUS
TRIGGER
IN
(DC OUT 12V/
MONITOR
50mA MAX)
MULTI-ZONE
OUT
ZONE 2
& SOURCE
MONITOR
R
L
OUT
Hide quick links:
Advertisement
Table of Contents
