Omron H5S Datasheet page 19

Yearly Timer Operation
Yearly, 2 Circuits Yearly, 4 Circuits
Example: ON at 18:00 and OFF at 22:15 on March 25 every year.
Set the program in the following order.
March 25, 2006 (Start date)
Day
period
March 25, 2006 (End date)
Time 18:00 (ON time)
period
22:15 (OFF time)
1. Set the Mode Switch to P1 or P2.
→ For 4-circuit models, refer to
page 18.
TIMER
P1
P2
PULSE
RUN
2. Press YEAR for 1 s or more. (The
Time Switch enters yearly program
setting mode. *1)
3. Specify the start date using
and D . *2
The year can be set from the current
year to the next two years as shown
in the example. If the year is set to
"--", the operation performs every
year.
<Example>
If the current year is 2006, the
displayed year changes as follows.
-- → 06 → 07 → 08 → -- → 06 →
4. Press WRITE .
Specify the end date using
and D . *2
If the starting year has been set to
"--", the ending year cannot be set.
5. Press WRITE .
Set the ON time with h and
6. Press .
WRITE
h
Set the OFF time with and
7. Press WRITE to enter the settings.
*1 If one or more programs have already been set, the display starts showing the
set programs.
WRITE
To add another program, press
*2 Holding down the date- or time-setting keys rapidly advances the value.
Pressing decrements the value of the key that was last pressed.
Note:
• Yearly programs are added to weekly programs.
• All the start/end dates and ON/OFF times must be set. the maximum
number of yearly timer operations that can be set is four for each output
circuit.
• If multiple settings are required, repeat steps 3 through 7.
• All of the yearly programs for the selected circuit (output) can be checked by
WRITE
pressing in yearly program setting mode.
• The set data will be cleared if the Output Setting Switch is moved between
the TIMER and PULSE positions after the data has been set.
Shaded portion indicates
blinking of the indicator.
SUN MON TUE WED THU FRI SAT
Y , m
Y , m
Number of
remaining steps
m . *2
m
. *2
repeatedly until "--:--" is displayed.
Yearly Pulse-output Operation
Yearly, 2 Circuits Yearly, 4 Circuits
Example: To produce output for 2 minutes at 18:00 from March 25 to
April 9.
Set the program in the following order.
March 25, 2006 (Start date)
Day
period
April 9, 2006 (End date)
Time 18:00 (ON time)
period
2 minutes (Pulse width)
1. Set the Mode Switch to P1 or P2.
→ For 4-circuit models, refer to
page 18.
P1
TIMER
P2
PULSE
RUN
2. Press YEAR for 1 s or more. (The
Time Switch enters yearly program
setting mode. *1)
3. Specify the start date using
D
and . *2
The year can be set from the current
year to the next two years as shown in
the example. If the year is set to "--" ,
the operation performs every year.
<Example>
If the current year is 2006, the
displayed year changes as follows.
-- → 06 → 07 → 08 → -- → 06 →
4. Press WRITE .
Specify the end date using
D
and . *2
If the starting year has been set to
"--", the ending year cannot be set.
5. Press WRITE .
h
Set the ON time with and
6. Press WRITE .
Set the pulse width with PLS
The displayed pulse width changes
by pressing this key in the following
order.
1 s → 2 s → ··· 59 s → 1 m → ···
59 m → 60 m → 1 s
7. Press WRITE to enter the settings.
*1 If one or more programs have already been set, the display starts showing the
set programs.
WRITE
To add another program, press
*2 Holding down the date- or time-setting keys rapidly advances the value.
Pressing decrements the value of the key that was last pressed.
Note:
• Yearly programs are added to weekly programs.
• All the start/end dates, ON time, and pulse width must be set. The maximum
number of yearly pulse output operations that can be set is four for each
output circuit.
• If multiple settings are required, repeat steps 3 through 7.
• All of the yearly programs for the selected circuit (output) can be checked by
WRITE
pressing in yearly program setting mode.
• The set data will be cleared if the Output Setting Switch is moved between
the TIMER and PULSE positions after the data has been set.
Digital Time Switch
Shaded portion indicates
blinking of the indicator.
SUN MON TUE WED THU FRI SAT
Y , m
Y m
,
Number of
remaining steps
m . *2
.
repeatedly until "--:--" is displayed.
H5S
19