Advertisement
Quick Links
General-purpose Limit Switch
Economical, Miniature Limit Switch
Boasting Rigid Construction
Highly rigid construction (head and cover snugly fit
in box).
Dustproof and drip-proof construction.
Smooth operation with greater OT.
Easy-to-wire conduit opening design.
Models with grounding terminals conform to the CE
marking.
Ordering Information
Model Number Legend
HL-5jjj
1
2
3
1. Actuators
000: Roller lever
030: Adjustable roller lever
050: Adjustable rod lever
100: Sealed plunger
200: Sealed roller plunger
300: Coil spring
500: Remote control wire
List of Models
Actuator
Roller lever
Model
HL-5000
Note: HL-5000 Limit Switches are offered with a choice of ground terminal/M5 tapping on the rear side conforming to various standards.
When placing an order, add the code to the model number to indicate if ground terminal/M5 tapping on the rear side is required.
-G: with ground terminal/M5 tapping on the rear side
Adjustable
Adjustable
roller lever
rod lever
HL-5030
HL-5050
2. Ground Terminal Specifications
Blank: Without ground terminal
G:
With ground terminal/M5 tapping on the rear side
3. Contact
Blank: Standard (silver rivet contact)
A:
Gold plating
Sealed
Sealed roller
plunger
HL-5100
HL-5200
HL-5000
Coil spring
plunger
HL-5300
1
Advertisement
Related Manuals for Omron HL-5000
Summary of Contents for Omron HL-5000
-
Page 1: Ordering Information
Note: HL-5000 Limit Switches are offered with a choice of ground terminal/M5 tapping on the rear side conforming to various standards. When placing an order, add the code to the model number to indicate if ground terminal/M5 tapping on the rear side is required. -
Page 2: Specifications
2. The above characteristics may vary depending on the model. For further details, contact your OMRON sales representative. 3. Life expectancy values are calculated at an operating temperature of 5 C to 35 C, and an operating humidity of 40% to 70%. Con- tact your OMRON sales representative for more detailed information on other operating environments. -
Page 3: Operating Characteristics
30 0.8 mm 40 0.8 mm Note: 1. Measured with the types of the 31.5-mm arm or rod length. 2. OF and RF measured at the arm length of 75 mm for HL-5030, and 145 mm for HL-5050 (reference values). Model HL-5030 HL-5050 3.09 N... - Page 4 HL-5000 HL-5000 Dimensions Note: 1. All units are in millimeters unless otherwise indicated. 2. Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. Roller Lever HL-5000 17.5 dia. (See note 1) (See note 2) Three, M5 x 12 Note: 1.
- Page 5 To change the angle of the actuator, loosen the Allen-head bolt on To change the head direction, loosen the two mounting screws. the side of the actuator lever. Then the actuator can be set at any Then the head can be changed at 90 increments in one of four angle.
- Page 6 Note: Do not use wires containing silicone, otherwise a contact failure may result. Applicable Solderless Terminal The following solderless terminals are available. Do not use fork or any other type of terminals, otherwise an accidental disconnection resulting in a ground fault may result.
- Page 7 ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. Cat. No. C004-E1-9...