Table of Contents
Advertisement
Connections
Here is an explanation
of typical
ways to connect
various
components
to the TX-SR701/701E/601/601E.
There are many
ways thai any one
component
can be connected,
and it is up to you to decide
which method
best fits your sima/ion.
The directions
given here are only one option
and should
only be thought
of as such.
It is best to fully understand
the nature
of each connector
and terminal
as well as those
of your
components
and their features
to ascertain
which method
of connection
is best.
Digital audio output (coaxial)
I
1. CD player (CD)
__
L (white)
-I
Analog audio output
R (red)
2.Turntable (PHONO) 1
(701/70t E only)
/ Ground wire
(earth)
L (white)
Analog audio output
R (red)
: Signal flow
3. Cassette tape deck,
|
MD recorder, DATdeck,
/
or CD recorder (TAPE)
L(white)
P
( p"
)
_
Analog audio output
R (red)
L (white)
Analog audio input
R (red)
Connecting your audio components
Below
is an
example
of
how
you
can
connect
your
audio
components
to the TX-SRT01/701E/601/601E.
Refer to the diagram
above for the following
connection
examples.
IN/OUT
(analog
audio)
'Ihese
are the analog
audio
inputs
and outputs.
There
are seven
audio
inputs
and three
audio
oulputs
on the rear panel. The audio
inputs and outputs
require
RCA-type
connectors.
DIGITAL
INPUT/OUTPUT
On the rear panel
of the TX-SR701/70IE/601/601E,
there are one
coaxial
digital
input,
two optical
digital
inputs,
one coaxial
digital
output
(TX-SRT01/70IE
only),
and
one
digital
output.
To the
digital
inputs,
connect
CD players,
LD players,
DVD
players,
or
other digital
source component.
'15 the digital outputs,
connect
MD
recorders,
CD recoMers,
DAT decks, or other similar
components.
•
Since
an analog
connection
must
be made
when
using
REC
OUT
or ZONE
2, make
sure that the connection
to the input
source
is not digital only, but analog as well.
•
When
using
an optical
input
or output
,jack,
always
use an
optical
fiber cable.
1.
Connecting
a compact
disc player
(CD)
Using an RCA audio cable,
connect
the output ,jacks of the compact
disc player to the CD audio,jacks
of the TX-SR701/70I
E/601/601E.
Make sm-e that you properly
connect
the left channel
to the L ,jack
and the right channel
to the R,jack.
If the compact
disc player
has a digital
output,
connect
it to either
the DIGITAL
INPUT
COAXIAL
,jack or the DIGITAL
INPUT
OPTICAL
jack of the TX-SR701/70IF/601/60IE
depending
on the
type of connector
on the compact
disc player.
With
the
initial
settings
of the TX-SR7OII7OIEI6OI/6OIE,
the
CD input
source
is set fbr digital
input at the COAXIAL
jack
(COAX).
If the digital
connection
is made
to a different
,jack, this must
be
changed
at "Input
Setup"
--> "Digital
Input"
(see page 52).
2.
Connecting
a turntable (PHONO) (TX-SR7OI/701E
only)
Using an RCA audio cable,
connect the output,jacks
of the turntable
to the PHONO
audio jacks
of the TX-SRT01/701E.
Make sm-e that
you properly
connect
the left channel
to the L ,jack and the right
channel
to the R,jack.
Note:
The
TX-SR701/701E
is designed
for use
with
moving
magnet
cartridges.
For proper
operation,
connect
a ground (or earth) wire to
the GND
lerminal.
I:or some turntables,
however,
connecting
the
ground
wire
may
cause
increased
noise,
and in such
a case,
a
ground
wire is not necessary
and should not be connected.
3.
Connecting
a cassette
tape deck, MD recorder,
DAT deck, or
CD recorder
(TAPE)
Using
RCA
audio
cables,
connect
the output,jacks
(PLAY)
of the
device
to the TAPE
IN audio
,jacks
of the TX-SR701/70IE/60I/
601E and connect
the input jacks
(REC)
of the device
to the TAPE
OUT audio
jacks
of the TX-SRT01/70IF/601/60IE.
Make sm-e that
you properly
connect
the left channels
to the L ,jacks and the right
channels
to the R,jacks.
If the device has a digital output, connect
it to eilher the DIGITAL
IN
COAXIAL,jack
or the DIGITAL
IN OKI ICAL,jack
of the TX-SR701/
701 E/601/601E
depending
on the type of connector
on the device.
With
the
initial
settings
of
the
TX-SR701/7OIE/6OI/601E,
nothing
is allocated
as the digital input source
t_r TAPE (----).
If you
connect
the
digital
audio
output,
be
sure
to make
the
appropriate
changes
at "Input
Setup"
--> "Digital
Input"
(see page
52).
If the
device
has
a digital
input,
connect
it to
the
DIGITAL
OUTPUT
,jack
of
the
TX-SR701/701E/601/601E
for
digital
recording
of the signal
from
the digital
input
of the TX-SR70I/
701E/601/601E.
Note:
The output
from the DIGITAL
OUT,jack
of the TX-SR701/701E/
601/601E
is only the digital
signal input to the DIGITAL
IN,jack.
16
Advertisement
Table of Contents
