Table of Contents
Advertisement
Selecting an Audio Component
AUDIO SELECTOR
Selecting the type of audio input signal
Px-essthe AUDIO SELECTOR bullon on the front panel (or AUDIO
SEL bullon on the remole controller) to change the audio mode.
Each time the button is pressed, the mode changes from "Auto" -+
"Multich" (only ifDVD is selected as the input source) --> "Analog"
and back to ''Auto)'
TX-SR701/701E/601/601E
AUD_
SELEGTG_I
Remote controller
AUOK_ 8EL
Auto (automatic
detection):
With this setting, the TX-SR701/
701E/601/601E
automatically detects whether the input signal is
digital or analog. When a digital signal is not input, then the analog
signal is played. This setting only appears if a digital input is
seleoed for the Digital Input setting at "Input Setup" --_ "Digital
Input" (see page 52).
Multich
(Multichannel):
Select this setting
to play back the multi-
channel input from a DVD player
with a 5A-channel
input port.
Analog:
Select
this
selling
to play back
the input fxom a source
component
conneoed
to analog
audio input.jacks.
With this selling,
even if a digital
signal is input fxom the same component,
only the
analog signal will be outpuL
Selecting the setting mode with the Cursor • /•
button
while "Auto" appears
Auto: The digital
signal suitable for the input signal will be
preceded for playback. When there is no digital signal input, analog
signal will be played.
DTS: Select this if you play DTS-formatted
CD in "Auto" mode
and hear noise during fast-forward
or rewind opera/ion. Non-DTS
sound input will not be output.
PCM:
Select this if you heat sound gap between
PCM tracks
such
as ones on CD in "Auto"
mode.
Non-PCM
sound input
will not be
output.
Notes:
• When you play DTS-formatted
CD or LD, be suxe to select
''Auto" or "DTS." If you select "PCM," noise will be heard.
• If a DTS signal is not input when "DTS" is selected, the TX-
SR701/701E/601/601E
will not automatically
switch to analog
output
even though
''Auto"
is selected
with
the AUDIO
SELECTOR button.
RCVR MODE
CH SEL
AUDIO SEL
LEVEL&IV
TAP
Notes on DTS:
If you play a DTS-formatted
CD or LD when the "PCM"
setting is selected on the TX-SR701/701E/601/601E,
the DTS
encoded signal will not be decoded and noise will be output.
This noise could damage the amplifier and speakers. Therefore,
be sure to select ''Auto" or "DTS" and use the digital input ,jacks
(OPT or COAX) to connect the DTS source.
• If you play a DTS-formatled
CD or LD when "Auto" is
selected, you may heat a noise for a short while until the DTS
decoder
recognizes
the
DTS-encoded
signal
and
starts
opera/ing. This is not a malfunction,
• If you press the pause or skip button on the player while playing
a DTS source, a short noise may be heard. This is not a
malfunction. In such cases, try playing the source in the "DTS"
selected.
•
The DTS
indica/or
on the
TX-SR701/701E/601/6OIE
lights
while a DTS source
is played.
When playback
finishes
and the
DTS signal
transmission
stops,
the TX-SR701/701E/601/601E
remains
in DTS mode
and the DTS indicator
remains
lit. 'Ihis
prevents
noise when you operate
the pause or skip button on the
player.
'lhexefore,
if the source
is immediately
swilched
fx-om
DTS to PCM,
the PCM signal may not be played.
In this case,
stop the playback
of the source
on the player
for about
thxee
seconds
and then resume
playback.
•
You may not be able to play
some DTS
source
signals
from
certain
CD players
and LD players
even when you connect
the
player
to
the
TX-SR701/701E/601/601E
digitally.
This
is
because
the digital
signal
has
been
processed
(such
as the
output
level,
sampling
frequency,
or frequency
response)
and
the TX-SR701/701E/601/601E
cannot
recognize
the signal
as
DTS da/a. Therefore
you may hear noise when you play a DTS
source while
processing
the signal.
The outputs
for the VIDEO
1 OUT, VIDEO
2 OUT, and 'IAPE
OUT output
analog
audio
signals.
Do not record
fxom CDs or
LDs that support
DTS using these outputs.
If you do, the DTS-
encoded
signal will be recorded
as noise.
• If a CD or LD encoded in the DTS format is played back with
"PCM" selecled, only noise will be produced. Always select
''Auto" or "DTS" when playing back DTS-encoded
sources.
42
Advertisement
Table of Contents
