Compressor; Limiter - Roland VERSELAB MV-1 Parameter Manual

MFX Parameters
Parameter Value
Speaker Sw OFF, ON
SMALL 1
SMALL 2
MIDDLE
JC-120
BUILT-IN 1
BUILT-IN 2
BUILT-IN 3
Speaker Type
BUILT-IN 4
BUILT-IN 5
BG STACK1
BG STACK2
MS STACK1
MS STACK2
MTL STACK
2-STACK
3-STACK
Mic Setting 1, 2, 3
Mic Level 0–127
Direct Level 0–127
Pan L64–63R
Level 0–127
28
Explanation
Determines whether the signal passes
through the speaker (ON), or not (OFF).
Diameter (in
inches) and
Cabinet Microphone
number of the
speaker
Small open-back
10 Dynamic
enclosure
Small open-back
10 Dynamic
enclosure
Open back
12 x 1 Dynamic
enclosure
Open back
12 x 2 Dynamic
enclosure
Open back
12 x 2 Dynamic
enclosure
Open back
12 x 2 Condenser
enclosure
Open back
12 x 2 Condenser
enclosure
Open back
12 x 2 Condenser
enclosure
Open back
12 x 2 Condenser
enclosure
Sealed enclosure 12 x 2 Condenser
Large sealed
12 x 2 Condenser
enclosure
Large sealed
12 x 4 Condenser
enclosure
Large sealed
12 x 4 Condenser
enclosure
Large double
12 x 4 Condenser
stack
Large double
12 x 4 Condenser
stack
Large triple stack 12 x 4 Condenser
Adjusts the location of the microphone that
is recording the sound of the speaker.
This can be adjusted in three steps, with the
microphone becoming more distant in the
order of 1, 2, and 3.
Volume of the microphone
Volume of the direct sound
Stereo location of the output sound
Output Level

33 Compressor

Flattens out high levels and boosts low levels, smoothing out
fluctuations in volume.
L in
Compressor Compressor
R in
Compressor Compressor
Parameter Value
Attack 0–124
Release 0–124
Threshold -60–0 [dB]
Knee 0–30 [dB]
1:1, 1.5:1, 2:1, 4:1,
Ratio
16:1, INF:1
Post Gain 0–+18 [dB]
Level 0–127

34 Limiter

Compresses signals that exceed a specified volume level, preventing
distortion from occurring.
L in
Limiter Limiter
R in
Limiter Limiter
Parameter Value
Release 0–127
Threshold 0–127
Ratio 1.5:1, 2:1, 4:1, 100:1
Post Gain 0–+18 [dB]
Low Gain -15–+15 [dB]
High Gain -15–+15 [dB]
Level 0–127
L out
2-Band EQ 2-Band EQ
R out
2-Band EQ 2-Band EQ
Explanation
Sets the time from when the input exceeds
the Threshold until the volume starts being
compressed
Adjusts the time after the signal volume falls
below the Threshold Level until compression
is no longer applied.
Adjusts the volume at which compression
begins
This is a function that smooths the onset of
compression from the uncompressed state; it
gradually applies compression starting earlier
than Threshold. Higher values produce a
smoother transition.
Compression ratio
Adjusts the output gain.
Output Level
L out
2-Band EQ 2-Band EQ
R out
2-Band EQ 2-Band EQ
Explanation
Adjusts the time after the signal volume falls
below the Threshold Level until compression
is no longer applied.
Adjusts the volume at which compression
begins
Compression ratio
Adjusts the output gain.
Gain of the low range
Gain of the high range
Output Level