Clip Setting; Looper Setting; Meas Edit (Only Looper); Sample Edit Parameter - Roland VERSELAB MV-1 Parameter Manual

Parameter Value
High Gain -24–+24 [dB]
HighFreq 20–16000 [Hz]
COMP
(Other than VOCAL)
Parameter Value
Switch OFF, ON
Pos Pre MFX, Post MFX
Attack 0.1–100 [ms]
Release 10–1000 [ms]
Thres -60–0 [dB]
Ratio 1: 1–inf: 1
Knee 0–30 [dB]
Gain -24–+24 [dB]
Out Asgn DRY, MFX
MIDI
(Other than VOCAL)
Parameter Value
TxMIDI Out OFF, ON
TxUSB MIDI OFF, ON
Tx Note OFF, ON
Tx CC OFF, ON
Tx PC OFF, ON

CLIP SETTING

Parameter Value
Mix Level 0–127
Pan L64–0–63R
Delay Send 0–127
Rev Send 0–127
Shuffle -50–+50
(*1)
Step Length 1–128
1/8,
1/16,
1/32,
Scale
(*1)
1/4T,
1/8T,
1/16T
FWD,
REV,
Mode FWD+REV,
(*1)
INV,
RND
Qtz C.Tight OFF, 1–100 %
(*1)
Transpose -12–+12
(*1)
Explanation
Gain of the high frequency range.
Frequency of the high range.
Explanation
Compressor on/off
Location of the compressor.
Time from when the input exceeds the
threshold until compression begins
Time from when the input falls below the
threshold until compression is turned off
Level at which compression is applied
Compression ratio
This is a function that smooths the onset of
compression from the uncompressed state; it
gradually applies compression starting earlier
than Threshold. Higher values produce a
smoother transition.
Level of the output sound
Specifies the compressor output destination.
Explanation
Enables output to the rear panel MIDI OUT
connector.
Enables output to the rear panel USB port.
Specifies whether the notes of each track are
output.
* This is not shown for a looper track.
Specifies whether knob operations of each
track are output.
Specifies whether clip changes of each track
are output.
Explanation
Adjusts the volume of each part.
Specifies the panning of each part's sound
when using stereo output.
Specifies the send level to delay.
Specifies the send level to reverb.
Adjusts the strength of shuffle (bounce) for
the playback timing.
This can be set individually for each clip.
Specifies the length of the clip.
Specifies the step resolution.
1/8: eighth notes
1/16:
sixteenth notes
1/32:
thirty-second notes
1/4T: quarter note triplets
1/8T: eighth note triplets
1/16T:
sixteenth notes triplets
Specifies how the sequence plays.
FWD: Play forward from the first step.
REV: Play backward from the last step.
FWD+REV:
Play forward from the first
step, and after reaching the last step, play
backward.
INV: Play even numbers and odd numbers
inverted.
RND: Play randomly.
Specifies the strength of quantization for the
currently selected clip.
Quantization is applied during playback.
Shifts the playback transposition (Tone only).
Parameter Value
Reverse OFF, ON
(*2)
Pad Octave -5–+5
Bend Mute OFF, MUTE
(*1)
NONE, C, C#, D, D#, E,
Key
F, F#, G, G#, A, A#, B
Specifies the scale from which the chord is
extracted.
Scale
& For details on scales, refer to "List of scales
(when KEY is C)" (p. 8).
*1 Valid when the track type is set to other than LOOPER.
*2 Valid when the track type is set to LOOPER

LOOPER SETTING

Parameter Value
Level 0–127
Pan L63–63R
Delay Send 0–127
Reverb Send 0–127
Pitch Chrom -24–+24
Pitch Fine -100–+100
Pitch Shift 0–400 %
PitchStrch OFF, TYPE1, TYPE2
1.0, 0.75, 0.5, 0.375,
Str Window
0.25
Reverse OFF, ON
MEAS EDIT
(Only LOOPER)
Parameter Value
Step Length 1–128
Reverse OFF, ON

SAMPLE EDIT Parameter

Parameter Value
Start 0–
End 0–
Norm Level -12–0dB
NORMALIZE EXEC —
Slice Level HARD, MID, SOFT
Parameter List
Explanation
OFF: The sample plays forward.
ON: The sample plays backward.
Specifies the octave for pad performance.
Disables bend (Tone only).
Specifies the note When a key or scale
that will be the key of is set for a clip and
the scale. the clip is loaded into
another project, the
clip is automatically
transposed to match
the MASTER KEY and
scale of the project.
Explanation
Specifies the volume at which the sample
plays.
Specifies the pan of the sound.
Adjusts the amount sent to the total effect
delay.
Adjusts the amount sent to the total effect
reverb.
Specifies the pitch in semitone steps
(maximum ±2 octaves).
This setting can also be made in PAD MODE
NOTE.
Finely adjusts the pitch.
Smoothly modifies the pitch in a wide range.
Selects the pitch shift / time stretch method.
OFF:
Time stretch is not used; the sample is
lengthened by changing its pitch.
* If OFF is selected, the settings in the PITCH tab
are ignored (pitch shift is not applied).
TYPE1: Time stretch optimized for melodic
material is applied.
TYPE2:
Time stretch optimized for rhythm
material is applied.
This parameter applies to time stretch.
Higher values improve the audio quality.
If an unnatural impression results when pitch
shift or time stretch is used to create a large
amount of change, lowering this value might
improve the result.
OFF:
The sample plays forward.
ON:
The sample plays backward.
Explanation
Specifies the length of the clip.
* The same setting can also be made in the CLIP
settings screen ([SHIFT] + [CLIP]).
Specifies the sample playback method.
* The same setting can also be made in the CLIP
settings screen ([SHIFT] + [CLIP]).
Explanation
Sets where to start playback.
Sets where to end playback.
Sets the peak value (maximum) for the
normalized waveform.
Press the [VALUE] dial to normalize.
Normalization automatically raises the
volume to the range where the sound does
not distort.
Sets the slice sensitivity.
5