Reverse Delay; Time Ctrl Delay - Roland VERSELAB MV-1 Parameter Manual

MFX Parameters

42 Reverse Delay

This is a reverse delay that adds a reversed and delayed sound to the
input sound.
A tap delay is connected immediately after the reverse delay.
L in
Rev. Delay Rev. Delay
Feedback
R in
Parameter Value
Threshold 0–127
Rev Delay Time
(sync
OFF, ON
sw)
Rev Delay Time 1–1300 [msec]
(msec)
Note
Rev Delay Time
(note)
&
"Note" (p. 51)
Rev Delay Feedback -98–+98 [%]
200, 250, 315, 400, 500,
630, 800, 1000, 1250,
Rev Delay HF Damp 1600, 2000, 2500, 3150,
4000, 5000, 6300, 8000,
BYPASS [Hz]
Rev Delay Pan L64–63R
Rev Delay Level 0–127
Delay 1 Time OFF, ON
(sync sw)
Delay 1 Time 1–1300 [msec]
(msec)
Note
Delay 1 Time
(note)
&
"Note"
(p. 51)
Delay 2 Time OFF, ON
(sync sw)
Delay 2 Time 1–1300 [msec]
(msec)
Note
Delay 2 Time
(note)
&
"Note" (p. 51)
Delay 3 Time OFF, ON
(sync sw)
Delay 3 Time 1–1300 [msec]
(msec)
Note
Delay 3 Time
(note)
&
"Note" (p. 51)
Delay 3 Feedback -98–+98 [%]
200, 250, 315, 400, 500,
630, 800, 1000, 1250,
Delay HF Damp 1600, 2000, 2500, 3150,
4000, 5000, 6300, 8000,
BYPASS [Hz]
Delay 1 Pan L64–63R
Delay 2 Pan L64–63R
Delay 1 Level 0–127
Delay 2 Level 0–127
Low Gain -15–+15 [dB]
High Gain -15–+15 [dB]
Balance D100:0W–D0:100W
Level 0–127
32
2-Band EQ 2-Band EQ
Rev
D1
Delay Delay
D3 D2
2-Band EQ 2-Band EQ
Explanation
Volume at which the reverse delay will begin
to be applied
If this is ON, the rate synchronizes with the
tempo of the rhythm.
Delay time from when sound is input into the
reverse delay until the delay sound is heard
Proportion of the delay sound that is to be
returned to the input of the reverse delay
(negative (-) values invert the phase)
Frequency at which the high-frequency
content of the reverse-delayed sound will be
cut (BYPASS: no cut)
Panning of the reverse delay sound
Volume of the reverse delay sound
If this is ON, the rate synchronizes with the
tempo of the rhythm.
Delay time from when sound is input into the
tap delay until the delay sound is heard
If this is ON, the rate synchronizes with the
tempo of the rhythm.
Delay time from when sound is input into the
tap delay until the delay sound is heard
If this is ON, the rate synchronizes with the
tempo of the rhythm.
Delay time from when sound is input into the
tap delay until the delay sound is heard
Proportion of the delay sound that is to
be returned to the input of the tap delay
(negative (-) values invert the phase)
Frequency at which the hi-frequency content
of the tap delay sound will be cut (BYPASS:
no cut)
Panning of the tap delay sounds
Volume of the tap delay sounds
Gain of the low range
Gain of the high range
Volume balance between the direct sound (D)
and the delay sound (W)
Output Level

43 Time Ctrl Delay

A stereo delay in which the delay time can be varied smoothly.
L in
L out
R in
R out
Parameter Value
Delay Time OFF, ON
(sync sw)
Delay Time 1–1300 [msec]
(msec)
Note
Delay Time
(note)
&
Acceleration 0–15
Feedback -98–+98 [%]
200, 250, 315, 400, 500,
630, 800, 1000, 1250,
HF Damp 1600, 2000, 2500, 3150,
4000, 5000, 6300, 8000,
BYPASS [Hz]
Low Gain -15–+15 [dB]
High Gain -15–+15 [dB]
Balance D100:0W–D0:100W
Level 0–127
Balance D
2-Band EQ 2-Band EQ
Time Ctrl Time Ctrl
Balance W
Delay Delay
Feedback
Feedback
Time Ctrl Time Ctrl
Balance W
Delay Delay
2-Band EQ 2-Band EQ
Balance D
Explanation
If this is ON, the rate synchronizes with the
tempo of the rhythm.
Delay time from when the original sound is
heard to when the delay sound is heard
"Note" (p. 51)
Speed at which the current delay time
changes to the specified delay time when you
change the delay time. This affects the speed
of pitch change as well as the delay time.
Adjusts the proportion of the delay sound
that is fed back into the effect. Negative (-)
settings will invert the phase.
Adjusts the frequency above which the delay
sound fed back to the effect is filtered out
(BYPASS: no cut).
Gain of the low range
Gain of the high range
Volume balance between the direct sound (D)
and the delay sound (W)
Output Level
L out
R out