Table of Contents
Advertisement
Quick Links
BEFORE YOU BEGIN
BEFORE YOU BEGIN
·
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
·
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
·
These instructions contain important care, cleaning, and
warranty information -
consumer
.
·
Fixture dimensions are nominal and conform to tolerances
established by ASME Standards (A112.19.2-2018).
·
The product complies with Q/KCI-006-2018 and GB
25502-2017.
ORDERING INFORMATION
Veil WH Toilet W/O ST
(HT110H P,3.0/4.5,HC)..................................K-25839T-NSHC
Include Veil WH Bowl W/O Seat .....................K-5723T-HC
Include HT110H IWT W/F
3.0/4.5L(Veil WH HC) ............K-32789T-VLWP-NA
Veil WH Toilet W/O ST
(HT300 P,3.0/4.5,HC) ....................................K-29918T-NSHC
Include Veil WH Bowl W/O Seat .....................K-5723T-HC
Include HT300 IWT W/F
3.0/4.5L(Veil WH HC) ............K-20010T-VLWP-NA
C3 Toilet Seat With Bidet Functionality (Not Provided)
No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 528137
8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA
NO.1 KOHLER STREET, ECONOMIC DEVELOPMENT ZONE OF FAKU COUNTY, SHENYANG LIAONING PROVINCE, PRC
1461371-T01-C
please leave instructions for the
·
·
·
·
2018)
·
Q/KCI-006-2018 GB 25502-2017
(
,
110H
110H
3.0/4.5 (
(
,
300
300
3.0/4.5 (
C3
2
528137
8
256410
1
110400
©
Copyright Kohler China Investment Co., Ltd. 2021
-1-
©
VEIL
INSTALLATION INSTRUCTION
WALL-HUNG TOILET
3.0/4.5
K-25839T-NSHC/K-29918T-NSHC
ASME
C3
,3.0/4.5 ).........K-25839T-NSHC
(
) ..................K-5723T-HC
,
) ............K-32789T-VLWP-NA
C3
,3.0/4.5 )...............K-29918T-NSHC
(
) ..................K-5723T-HC
,
) ............K-20010T-VLWP-NA
(
)
POST CODE:
256410
POST CODE:
-
(A112.19.2-
:
110400
2021
Advertisement
Table of Contents
Related Manuals for Kohler K-25839T-NSHC
Summary of Contents for Kohler K-25839T-NSHC
- Page 1 3.0/4.5L(Veil WH HC) ....K-20010T-VLWP-NA C3 Toilet Seat With Bidet Functionality (Not Provided) No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 528137 528137 8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA...
- Page 2 · · Waxseal · · Supply Shut-off Valve · · Level · · Screwdriver · · Sponge · · Sealant ROUGHING-IN Reference Value UNIT mm 285 385 Fig.#1 Kohler reserves the right to change marked dimensions without prior notice. 1461371-T01-C...
- Page 3 SPECIFICATION Plumbing Connections Recommended inlet connections are 1/2 BSP. " 1/2" BSP INSTALLATION 3/4.5L Recommended tanks for 3/4.5L In-wall Tank K-20010T-VLWP-NA/K-32789T-VLWP-NA K-20010T-VLWP-NA/K-32789T-VLWP-NA K-20010T-VLWP-NA K-32789T-VLWP-NA Fig.#2-a Fig.#2-b Install the Toilet 1. Install Flushing Mechanism · · Turn the water supply off before installing the new toilet. ·...
- Page 4 2. Set The Spacing Of The Bowl After you install the tank, be careful to set the spacing of the bowl on wall according to the dimensions as shown. Unit: mm Carrier Studs 25 2 Fig.#4 3. Attach Connection Pipe 3.1.
- Page 5 3.3. Install the tank system per tank's installation instructions, 3.3. then as shown, pull the inlet pipe of the Bidet seat through the bowl and connect it to the valve hose connector on the iron rack. Pull the plug of the Bidet seat through the bowl and connect it to the socket on the iron rack and then fix the Bidet seat.
- Page 6 CAUTION: Don t use any cement while installing the toilet. Heat expansion of the toilet may damage the feet of the toilet. Kohler will not be responsible for any damage because of using cement. WARNING: Risk of product damage. Do not throw into the toilet what is easy to block it, such as newspaper, paper pilch, sanitary towel.
- Page 7 HYDRO-TOWER 110 In-Wall Tank 海德丽 110 入墙式隐藏水箱 In-Wall Tank With Frame In-Wall Tank Without Frame 入墙式隐藏水箱（含固定支架）座便器 入墙式隐藏水箱（不含固定支架）座便器 KOHLER CHINA INVESTMENT CO., LTD NO.158, JIANG CHANG SAN ROAD, JING'AN DISTRICT, SHANGHAI, PRC POST CODE: 200436 科勒（中国）投资有限公司 上海市静安区江场三路 158 号 邮编：200436 1476533-K2-A...
-
Page 8: Table Of Contents
2I. After installation, the water supply and electricity can be connected and used ..............28 REMOVAL AND MAINTENANCE ����������������������������������������������������������������������������������������������������������� 28 A. Removal ....................................28 B. Maintenance ..................................31 TROUBLE SHOOTING PROCEDURES �������������������������������������������������������������������������������������������������� 32 © Copyright Kohler China Investment Co., Ltd. 2022 © 版权为科勒（中国）投资有限公司所有 2022 1476533-K2-A... - Page 9 目录 谢谢您选择科勒公司 ����������������������������������������������������������������������������������������������������������������������������������� 3 安装之前 ����������������������������������������������������������������������������������������������������������������������������������������������������� 3 规格 ������������������������������������������������������������������������������������������������������������������������������������������������������������ 5 所需工具及材料 ������������������������������������������������������������������������������������������������������������������������������������������ 5 尺寸图 ��������������������������������������������������������������������������������������������������������������������������������������������������������� 6 安装 ������������������������������������������������������������������������������������������������������������������������������������������������������������ 7 安装方式 ����������������������������������������������������������������������������������������������������������������������������������������������������� 7 安装方式一：入墙式隐藏水箱（含固定支架）座便器安装 �������������������������������������������������������������������������� 7 1A. 隐藏水箱安装 ..................................7 1B. 排污管安装方法 ..................................9 1C. 供水管连接 ..................................10 1D. 插座接线 ....................................10 1E. 预留检修口安装 ..................................11 1F.
-
Page 10: Thank-You For Choosing Kohler Company
• Do not apply components that are not provided by Kohler, and please note that glass adhesive tape shall not be applied to the installation of Kohler spares. Kohler will not be responsible for any damage related to installation with spares not provided by Kohler. - Page 11 Product Information HT110H IWT HC W/F 3.0/4.5L (HC)..........................K-32789T-*WP HT110H IWT HC W/O F 3.0/4.5L (HC)........................K-32790T-*WP HT110 IWT W/F 3.0/6.0L (TW) HC..........................K-32784TW-HC HT110 IWT W/F 3.0/4.5L (K) HC..........................K-32789K-HC HT110 IWT W/F 3.0/5.0L (MY) HC..........................K-32615MY-HC HT110 IWT W/O F 3.0/6.0L (TW) HC........................K-32785TW-HC HT110 IWT W/O F 3.0/4.5L (K) HC..........................K-32790K-HC HT110 IWT W/O F 3.0/5.0L (MY) HC.........................K-32616MY-HC Note: -* is the code for wall-hung or wall-faced toilet series that in-wall tank can match with, which may represent VL, RU.
-
Page 12: Specifications
Advantages of this In-Wall Tank • Made of macromolecular materials that prevent corrosion and leaking. • Advanced water tank fittings, which makes possible the adjustment of the water discharge and double gear flushing. • Will not affect the structure of the wall and provide excellent sound insulation. •... -
Page 13: Roughing-In
51 1 K-22525T-PNE K-6283T-PNE K-4177T K-8857T 328.5 1 328.5 1 215 1 215 1 K-20341T/K-20341T-PNE K-75890T/K-75890T-PNE K-75891T/K-75891T-PNE K-77271T 225 1 225 1 225 1 225 1 Kohler reserves the right to change marked dimensions without prior notice. 科勒公司保留随时变更图中标示尺寸的权利， 无需另行通知。 1476533-K2-A... -
Page 14: Installation
安装 INSTALLATION Installation methods 安装方式 There are two methods to install this product: In-Wall Tank with frame, In-Wall Tank without frame. 本产品具有两种安装方式：入墙式隐藏水箱（含固定支架）座 便器、入墙式隐藏水箱（不含固定支架）座便器。 In-Wall Tank With Frame In-Wall Tank Without Frame 入墙式隐藏水箱 入墙式隐藏水箱 （含固定支架） 座便器 （不含固定支架） 座便器 First method: Installation for In-Wall Tank with frame 安装方式一：入墙式隐藏水箱（含固定支架）座便器安装... - Page 15 Expanding Bolt Cap 3. Align the tank on the wall as shown and locate the 膨胀螺丝套 installation holes of the fixating bracket. Mark on the wall Washer 垫片 and floor for appropriate position for fixating the bracket, and drill four holes with a diameter of 12mm and a depth of Screw 螺丝...
-
Page 16: Discharge Pipe Installation Method
Stud 3. As Fig A, B, C shown, tighten the six M8 coach/tek screws 木框架 Fixing Hole 安装孔 (not supplied) to fixate the tank. M8 Coach/Tek Screws 3. 如图 A、 B、 C， 用 6 颗 M8 自攻螺丝 （产品未提供） 将水箱固定。 (Not Supplied) M8 自攻螺丝... -
Page 17: Connecting The Water Pipe
Two� Installation of p-trap 二 � 横排安装方法 Water Tank Bracket 水箱架 First of all, there are two discharge pipe installation methods based on actual situations: A, B. 首先根据实际情况有 A、B 两种排污管安装方法。 110mm Discharge Connector 110mm 排污转接头 A Install 110mm discharge connector onto 110mm drain outlet on the wall. -
Page 18: Installations Of Reserved Access Panel
1E� Installations of reserved access panel 1E� 预留检修口安装 Support Block 支撑块 Cover 遮板 Before Installation 安装之前 A. Remove the cover inside the water tank first as shown. Then remove the support block above the bracket assembly. A. 如图首先把水箱上的遮板取下，再取出支架组件上方的支撑块。 Half Flush Blue Air Hose Of Flush Valve 排水阀小冲蓝色气管... - Page 19 The following faceplates are only suitable for method two: Remote pinch installation 以下面板只适合安装方式二：远程扣板安装 K-23055T-PNE K-6283T-PNE K-22525T-PNE Mask 方外罩 1� Method one: Press from front (Mask is reserved access panel) 1� 安装方式一：前按（方外罩为预留检修口） Cover 遮板 Remove the cover, install the mask in the block screen of the Screw 螺丝...
- Page 20 Fixate Mask Onto Wall Method Three: Remote installation of mask 方外罩固定墙面 Leave a gap of at least 88mm. Finished 安装方式三：远程方外罩安装 Wall 完工墙面 墙面至少预留 88mm 深的避位 At Least 88mm Gap Reserved 建议预留至少 的避位 88mm Two� Intelligent faceplate reserved access panel installation, method one: press from front only Faceplate No�: 二...
-
Page 21: Brickwork Of The Wall
Output AC 6V 输出 AC6V Transformer Assy. 变压器组件 2� Installing the mask 2� 方外罩安装 Remove the cover, install the mask in the block screen of the tank, and tighten the screws to fixate the mask to the Mask 方外罩 tank. Cover Note: Do not remove and discard the mask cover before 遮板... -
Page 22: Installation Of Wall-Hung Toilet
2� Brickwork wall thickness, follow: 1E Installations of reserved access panel 2� 施工假墙厚度，按照步骤 1E：预留检修口安装 A. Press from front : Brickwork wall thickness 8~69mm from the front of tank. A. 前按：假墙厚度距水箱正面 8~69mm。 B. Remote installation: Brickwork wall thickness follow: 1E Installations of reserved access panel, remote installation part of normal pneumatic faceplate reserved access panel. - Page 23 进水管 Drainage Pipe 排污管 3. Apply lubricant to the drainage pipe and inlet pipe to ensure smooth installation. 3. 排污头及进水口涂上润滑油，使排污管、排水管安装顺畅。 Lubricant 润滑油 4. Install the drainage pipe and inlet pipe to the corresponding pipes on the tank. Mark A3, A4 on the drainage pipe and the inlet pipe at the back side of the wall with a ruler and a pencil.
- Page 24 7. As shown, remove the plug from the valve on the iron rack, then install the hose (Packed in tank) to the valve on the iron rack, pull the inlet pipe of the Bidet seat through the bowl Plug 堵头 and connect it to the valve hose connector on the iron rack.
-
Page 25: Installation Of Faceplate
1H� Installation of faceplate 1H� 面板安装 According to different faceplates, there are different faceplate installations as below: Cover 遮板 根据不同面板，面板有如下安装方式： Note: Remove the mask cover (if there is any mask). 注：取下方外罩遮板（有方外罩时）。 One� Normal pneumatic faceplate installation Faceplate No�: 一 � 常规气动面板安装方式 面板编号：... - Page 26 b. Tighten the four fixation pipes to the "LOCK" mark after installing the locking plate as shown. Fixation Pipe 固定管 b. 如图将定位板装上后，把四个固定管旋到 "LOCK" 字样 即可。 Locking Plate 定位板 B. Faceplate press from front or remote pinch installation. Locking Plate B. 适配远程扣板安装。 定位板...
- Page 27 Two� Intelligent faceplate installation Faceplate No�: 二 � 智能面板安装方式 面板编号： K-23056T K-23056TW K-24147T-7 K-78041-7 1� Installing the cover 1� 遮板安装 As shown, first pass the full flush dark gray and half flush blue air hoses, and the power output cable of the transformer through the cover.
- Page 28 3� Installing the air pump on the Intelligent faceplate 3� 智能面板气泵盒组件安装 A. Install the air pump assembly to faceplate and need Slot A 卡槽 attention: the slot of faceplate and the rib of air pump needs install properly to correspond. (A-A/B-B) Prevent Slot B 卡槽...
- Page 29 Three� Mechanical faceplate installation Faceplate No�: 三 � 机械面板安装方式 面板编号： K-4177T K-8857T K-20341T K-75890T K-75891T K-77271T 1� Installing the pneumatic cylinder (Packed in Full Flush Dark Gray Air Hose 大冲深灰色气管 mask box) 1� 气缸组件安装（方外罩包装盒内） Half Flush Blue Air Hose 小冲蓝色气管 As shown, connect the full-flush dark gray and the half-flush blue air hose to pneumatic cylinder, install bolt rod and nut Pneumatic Cylinder...
-
Page 30: After Installation, The Water Supply And Electricity Can Be Connected And Used
4� Fitting the faceplate 4� 面板固定 Faceplate 面板 Put the lock on the faceplate directly on the reversed lock Locking Faceplate 面板 Plate on locking plate, then push the faceplate and lock it. The 定位板 installation shall begin from bottom to top. Lock 扣位... -
Page 31: Discharge Pipe Installation Method
Spirit Level Note: 1. Following the steps: 2B. Discharge pipe installation 水平尺 method before fixating the tank. 2. Ensure that the tank remains level and plumb. 3. Keep the outlet pipe of the water tank upright. Do not Tank 水箱 bend it. -
Page 32: Brickwork Of The Wall
2F� Brickwork of the wall 2F� 砌墙 1� Protection of inlet hole and drainage hole 1� 进、排水口防护 As shown, fixate the EPE block onto the drainage hole and inlet hole. 如图将 EPE 挡块装在排污口和进水口上。 Inlet Hole 进水口 2� Brickwork wall thickness, follow: 1E Installations Drainage Hole 排污口... -
Page 33: Installation Of Wall-Faced Toilet
2G� Installation of wall-faced toilet 2G� 落地座便器安装 1. Install the big and small leak-proof gaskets on the inlet pipe and drainage pipe, and then install them to the Small Leak-proof Gasket 小防漏胶圈 corresponding pipes on the toilet. 1. 如图将座便器的排污管、进水管装上大、小防漏胶圈，然后 Inlet Pipe 进水管... - Page 34 5. Eliminate unwanted part of the drainage pipe and the inlet Inlet Pipe pipe according to the marks of reserved space L2+3, L1+3, 进水管 and rasp a smooth surface with files. 5. 如图在排污管、进水管已作标记的后端多余部分 L2+3，L1+3 锯掉。然后再用锉刀将锯掉的面挫平整并倒角。 Note: According to step 4, re-install the cut drainage pipe and inlet pipe into the corresponding pipes of the tank.
-
Page 35: Following The Steps: 1H. Installation Of Faceplate
8. Install the toilet as shown in the illustration, and use a spirit level to ensure the toilet remains level. 8. 如图将座便器装上，并用水平尺测量座便器是否平衡。 Spirit Level 水平尺 Note: Please refer to the installation instructions of the toilet. 注：实际安装座便器时，依照对应座便器的安装方法。 2H� Following the steps: 1H� Installation of faceplate Full 2H�... - Page 36 3. Dismantle the locking plate. Fixation Pipe 3. 如图拆出定位板。 固定管 Fixing Lock 固定扣 Locking Plate 定位板 4. If a cover is installed, remove the cover according to the figure. 4. 如有安装遮板，按图取下遮板。 Cover 遮板 5. As shown if there is pneumatic cylinder, hold the left and Full Flush Dark Gray Air Hose right snaps along the arrow direction to dismantle the 大冲深灰色气管...
- Page 37 7. Pull the fixation pin of the toilet detergent box to take the box out. 7. 如图提拉洁厕剂盒的锁紧轴，取出洁厕剂盒。 Fixation Pin 锁紧轴 8. Open/close the water supply Stop Valve Rotate the stop valve switch to open/close the water supply as shown. Open Close 8.
-
Page 38: Maintenance
10. Hold the fastener by hand as shown, pull the top of fastener along the direction of the arrow. Then remove the fastener. 10. 如图用手握住固定扣的上端向箭头方向拨动，然后取出固 定扣。 Fastener Fastener 固定扣 固定扣 11. Pull flush valve along the arrow direction as shown to remove flush valve. -
Page 39: Trouble Shooting Procedures
3� Cleaning the flush valve Clean the waste on the flush valve especially on the gasket with clean water. 3� 排水阀清洁 用清水清洗排水阀尤其是密封垫上的脏污。 Gasket 密封垫 故障排除 TROUBLE SHOOTING PROCEDURES Symptoms Probable Causes Recommended Actions The inlet valve is closed. Open inlet valve. No water fills in via inlet Floating box of inlet valve is blocked by other Readjust the position of other parts to avoid...