Table of Contents
Advertisement
■
[PJLink settings]
Configure the PJLink settings to enable PJLink
communication on the unit.
Lower than Version 1.5000 (before IPv6
compatible)
PJLink settings
Password policy
PJLink control
Password
PJLink notification
Notified IP address 1
Notified IP address 2
Save
Version 1.5000 and later (after IPv6 compatible)
PJLink settings
Password policy
PJLink control
Password
PJLink notification
Notified IP address 1
Notified IP address 2
Notified IP address 1 (IPv6)
2001:0d0d:111:ffff:1111:ffff:1111:ffff
Notified IP address 2 (IPv6)
2001:0d0d:111:ffff:1111:ffff:1111:ffff
Save
[Password policy]:
Precautions for password settings of this item will be
displayed in a new window.
[PJLink control]:
Specifies the PJLink communication settings.
Off:
Disables PJLink control.
On:
Enables PJLink control.
[Password]:
The keyboard for setting the password is displayed.
After entering the password, select [Ok]; the
confirmation screen is displayed. Enter the password
again and select [Ok]; the password is determined.
●
Entering characters (see page 177)
[PJLink notification]:
Set this item when using the PJLink notification.
[Off]:
Disables the notification.
[On]:
Enables the notification.
[Notified IP address 1], [Notified IP address 2]:
Set the IP address of the PC where the status of this
unit is notified.
[Notified IP address 1 (IPv6)], [Notified IP address
2 (IPv6)]
Set the IP address (IPv6) of the PC where the status
of this unit is notified.
Note
●
For IPv6 IP address entering method, refer to
"Entering numbers" (see page 83).
●
Initial values for notified IP addresses of IPv6 are
blank.
80
English
On
Off
192.168.0.100
192.168.0.101
On
Off
192.168.0.100
192.168.0.101
[Save]:
Saves the password determined above in the display
unit.
Note
●
Once determined, it is necessary to enter the
password to display the settings.
●
To set the setting to [On], you must configure
[Administrator account settings] in advance.
●
To use PJLink control, you need to set [On] to the
setting and set [Network control] to [On].
●
The password for the setting is different from the
password for [LAN setup].
■
[AMX D. D.]
Set whether to allow the Display to be detected by AMX
Device Discovery.
[Off]:
Disables detection by AMX Device Discovery.
[On]:
Enables detection by AMX Device Discovery.
●
For more details, visit the following web site.
http://www.amx.com/
Note
●
To set the setting to [On], you must configure
[Administrator account settings] in advance.
●
This function is disabled during communication with
IPv6 settings.
■
[Crestron Connected]
When this function is set to [On], the Display can be
monitored or controlled via the network using equipment
and application software of Crestron Electronics, Inc.
This Display supports the following application software
from Crestron Electronics, Inc.
Crestron Fusion
•
Crestron Connected is a function to connect to a system
developed by Crestron Electronics, Inc. which manages
and controls multiple system devices connected to the
network.
●
For details of Crestron Connected, refer to the
Crestron Electronics, Inc. web site (Provided only in
English).
http://www.crestron.com/
Note
●
To set the setting to [On], you must configure
[Administrator account settings] in advance.
●
This function is disabled during communication with
IPv6 settings.
Advertisement
Table of Contents
