Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gigabyte GS-SR 125 Series
Summary of Contents for Gigabyte GS-SR 125 Series
- Page 1 GS-SR 125 Series Rack Mount Server System Installation Guide...
-
Page 3: Table Of Contents
GS-SR125 Series System Installation Guide Contents SAFE, CARE AND REGULATORY INFORMATION PREFACE INTRODUCTION 3.1. SCSI M EATURE OF ODEL 3.2. IDE M EATURES OF ODEL CONTENTS PACKAGE 4.1. SCSI M OMPONENT ONTENT ODEL 4.2. IDE M OMPONENT ONTENT ODEL SYSTEM INSTALLATION PROCEDURES 5.3. - Page 4 GS-SR125 Series System Installation Guide The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to update the information contained herein. Third-party brands and names are the property of their respective owners.
-
Page 5: Safe, Care And Regulatory Information
GS-SR125 Series System Installation Guide 1. Safe, Care and Regulatory Information Important safety information Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. The product should be operated only from the type of power source indicated on the rating label. - Page 6 GS-SR125 Series System Installation Guide Precautions for Products With Laser Devices Observe the following precautions for laser devices: Do not open the CD-ROM drive, make adjustments, or perform procedures on a laser device other than those specified in the product’s documentation. Only authorized service technicians should repair laser devices.
- Page 7 GS-SR125 Series System Installation Guide generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
- Page 8 GS-SR125 Series System Installation Guide The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part 68, Sec. 68.381 (c) (3)). / for Canadian users only / Canadian Department of Communications Compliance Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada.
- Page 9 GS-SR125 Series System Installation Guide metallic water pipe system, if resent are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
-
Page 10: Preface
For your protection, please read and understand all of the safety and operating instructions regarding your Gigabyte Server and retain for future reference. The procedures in this guidebook assume that you are a system or network administrator experienced in installing similar hardware. -
Page 11: Introduction
GS-SR125 Series System Installation Guide 3. Introduction Welcome to the Gigabyte GS-SR125 Rack mount Server System Installation Guide. The guidebook provides instructions for configuration hardware for the GS-SR125 to your system. In order to get the optimal usage of your server, please pay... - Page 12 GS-SR125 Series System Installation Guide Features Description Motherboard GA-8IPPDR Processor Supported Support Dual Intel XEON Prestonia processors up tp 2.4 GHz+ (FSB 400 Mhz, 533Mhz Design Compliance) AMI BIOS with enhanced BIOS ACPI feature for PC99/Win98/ME/2000 compliance; Green, PnP, DMI, INT13 & Anti-Virus functions IDE #0-#3, SCSI, LS120, ZIP, and CD-ROM bootable.
- Page 13 GS-SR125 Series System Installation Guide Intelligent Management Standard supports IPMI v System 1.5 for system monitoring. IPMI card: GC-HP12E-Q Hot Swap Hard Disk Drive Support 4 SCSI Ultra-160 Bays (U-320 upgradeable) Hot- Swap HDD Mass Storage System Four low-profile shelves for hot-swappable drives One slim type flexible FDD drive...
-
Page 14: Features Of Ide Model
GS-SR125 Series System Installation Guide 3.2. Features of IDE Model Table... -
Page 15: Contents Package
GS-SR125 Series System Installation Guide 4. Contents Package When opening the package, please ensure the system components are not damaged during the shipping. Using the following checklist to verify the contents. If any component is missing or damaged in the system, please contact your vendor immediately. -
Page 16: System Installation Procedures
GS-SR125 Series System Installation Guide 5. System Installation Procedures Please remove the protective thin films (Top and bottom) from the system when installing. 5.3. Chassis Removal Step 1. Push down the two buttons located at two sides of the chassis. (Fig-1) Figure 1 Figure 2 Step 2.. -
Page 17: Cpu Installation
GS-SR125 Series System Installation Guide 5.4. CPU Installation Step 1. Please make sure the CPU type and speed that are supported by the motherboard. Step 2. To Install the CPU(s), lift up the bar that located next to the socket. (Fig-3) Figure 3 Step 3. -
Page 18: Heat Sink Installation
GS-SR125 Series System Installation Guide Figure 5 Figure 6 5.5. Heat Sink Installation Step 1. Put the Heat sink on the CPU. (Fig-7) Figure 7 Figure 8 Step 2. There are for screws hold the retention modules. Seat the heat sink firmly in the retention modules with the two cooler brackets. -
Page 19: Memory Installation
GS-SR125 Series System Installation Guide Step 5. Hook the other end of the cooler bracket by gripping it to another side of retention module. (Fig-9) Figure 9 5.6. Memory Installation The motherboard contains six DIMM (Dual Inline Memory Module) sockets. The systems BIOS will auto detect the size if the memory after installing. -
Page 20: Pci Expansion Card Installation
GS-SR125 Series System Installation Guide 5.7. PCI Expansion Card Installation GS-SR125 provides expansion riser slots for two peripheral cards, 64Bit/66 MHz full-height. To install the peripheral, please go through the following steps. Step 1. There are screws holding the riser bracket. Remove the screw on the top of the bracket. - Page 21 GS-SR125 Series System Installation Guide Figure 14 Figure 15 Step 3. Secure the card with screws. (Fig-15) Step 4. Repeat Step 2 to install another card. (Fig-16) Step 5. Secure the card with screws. (Fig-17) Figure 16 Figure 17 Step 6. Finally, align the stable racks to the system module, (see the arrow direction) and push down vertically to complete the installation.
-
Page 22: Reinstall Top Cover
GS-SR125 Series System Installation Guide Figure 18 5.8. Reinstall Top Cover When complete the installation of the entire essential components (from subsection 5.1 to 5.7), replace the plastic air duct. This will secure the airflow is inside the chassis. Failure to do so may cause CPU and Memory over heating. -
Page 23: Scsi Id Setting (For Scsi Model Only)
GS-SR125 Series System Installation Guide 5.9. SCSI ID Setting (For SCSI Model ONLY) The SCSI ID is shown in Figure 20. If there occurs an abnormal SCSI hard disk drive behavior (e.g. does not detect the hard disk drive properly), please make sure that the each HDD has different Figure 20... - Page 24 GS-SR125 Series System Installation Guide Jumper Setting For HD1, HD2, and HD3 Jumper ON (Jumper Close): 1-2 OFF (Jumper Open): 2-3...
-
Page 25: Dock Handle Installation
GS-SR125 System Installation Guide 5.10. Dock Handle Installation Remove the dock handles from the package. Put two on each side of the chassis, secure with screws provided. (Fig-21) Figure 21 5.11. Hard Disk Drive Installation Step 1. Pull the hard disk drive tray handle and remove the tray from the chassis (Fig-22). - Page 26 GS-SR125 Series System Installation Guide Figure 24 Figure 25 Step 2. After securing the hard disk drive with the screws, hold the hard drive handle at open position, place the tray into chassis (Fig-26) and push the hard disk drive tray handle to the closed position.
-
Page 27: Appearance Of Gs-Sr125
GS-SR125 Series System Installation Guide 5.12. Appearance of GS-SR125 5.12.1. Front View of GS-SR125 USB & LED Manufacture SCSI Ultra-160 Hot-Swap HDD Option: Floppy Disk/4th HDD tray 5.12.2. Rear View of GS-SR125... -
Page 28: Led Indicator Description
GS-SR125 Series System Installation Guide 5.12.3. LED Indicator Description Acting Color Status Power LED Green Power On Amber Power cable plug-in Blink Green System stands by No power SYS LED Amber System is ready but degraded: some CPU Fault, DIMM Killed Critical Power Modules Failure, Critical FANs Failure, Voltage (Power... - Page 29 GS-SR125 Series System Installation Guide HDD LED: HDD LED 1 HDD LED 2 Acting Color Status HDD LED 1 HDD Idle HDD LED 1 Blink Green HDD Acting HDD LED 2 No error HDD LED 2 Green Faulty or rebuild stop Slow Blink Green HDD LED 2 Rebuild...
-
Page 30: Floppy Drive Installation
GS-SR125 Series System Installation Guide 5.13. Floppy Drive Installation (Optional) Step 1. Remove three screws on the front top cover, (Fig-28) Push down the two buttons located at two sides of the system to remove front top cover. (Follow the arrow direction shown in Fig- Figure 28 Figure 29 Step 2. - Page 31 GS-SR125 Series System Installation Guide Step 3. Place the tray into chassis (Fig-32) and push the floppy disk drive tray handle to the closed position. Note: It will make “click” sound when the floppy disk drive is inserted properly Figure 32 Figure 33 Step 4.
-
Page 32: Connector Icon Description
GS-SR125 Series System Installation Guide 5.14. Connector Icon Description Suggested icons Description Keyboard Mouse Parallel Port Serial Port...