Related Manuals for Gigabyte GS-SR125ED
Summary of Contents for Gigabyte GS-SR125ED
- Page 1 GS-SR125ED Rack Mount Server System Installation Guide 1U Rack Mount Server Platform Solution...
-
Page 3: Table Of Contents
GS-SR125ED System Installation Guide Contents SAFE, CARE AND REGULATORY INFORMATION....1 PREFACE....................6 INTRODUCTION................. 7 3.1....................7 EATURE CONTENTS PACKAGE..............10 4.1............. 10 OMPONENT ONTENT SYSTEM INSTALLATION PROCEDURES ........11 5.2................11 HASSIS EMOVAL 5.3. CPU I ................ - Page 4 GS-SR125ED System Installation Guide omissions that may appear in this document nor does the author make a commitment to update the information contained herein. Third-party brands and names are the property of their respective owners. Third-party brands and names are the property of their respective owners.
-
Page 5: Safe, Care And Regulatory Information
GS-SR125ED System Installation Guide 1. Safe, Care and Regulatory Information Important safety information Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. - Page 6 GS-SR125ED System Installation Guide Precautions for Products With Laser Devices Observe the following precautions for laser devices: Do not open the CD-ROM drive, make adjustments, or perform procedures on a laser device other than those specified in the product’s documentation.
- Page 7 GS-SR125ED System Installation Guide generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
- Page 8 GS-SR125ED System Installation Guide The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part 68, Sec. 68.381 (c) (3)). / for Canadian users only / Canadian Department of Communications Compliance Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada.
- Page 9 GS-SR125ED System Installation Guide metallic water pipe system, if resent are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
-
Page 10: Preface
For your protection, please read and understand all of the safety and operating instructions regarding your Gigabyte Server and retain for future reference. The procedures in this guidebook assume that you are a system or network administrator experienced in installing similar hardware. -
Page 11: Introduction
Welcome to the Gigabyte GS-SR125ED Rack mount Server System Installation Guide. The guidebook provides instructions for configuration hardware for the GS-SR125ED to your system. In order to get the optimal usage of your server, please pay attention to the following tips: Go through the installation guide carefully before starting the system installation processes. - Page 12 GS-SR125ED System Installation Guide Features Description Motherboard GA-8IPP533 Processor Supported Support Dual Intel XEON Prestonia processors up to 3.06 GHz+ (FSB 533 MHz,) BIOS AMI BIOS with enhanced ACPI feature for PC99/Win98/ME/2000 compliance; Green, PnP, DMI, INT13 & Anti-Virus functions IDE #0-#3, SCSI, LS120, ZIP, and CD-ROM bootable.
- Page 13 GS-SR125EDSystem Installation Guide System (Option) 1.5 for system monitoring. Hot Swap Hard Disk Drive Support 4 IDE Hot-Swap Bays Mass Storage System Four low-profile shelves for hot-swappable drives One 3.5” FDD drive (Option) One slim type CD-ROM drive System Form Factor 1U, Rack-optimized design I/O expansion slots 2 riser cards to support 3...
-
Page 14: Contents Package
GS-SR125ED System Installation Guide 4. Contents Package When opening the package, please ensure the system components are not damaged during the shipping. Using the following checklist to verify the contents. If any component is missing or damaged in the system, please contact your vendor immediately. -
Page 15: System Installation Procedures
GS-SR125ED System Installation Guide 5. System Installation Procedures Please remove the protective thin films (Top and bottom) from the system when installing. 5.2. Chassis Removal Step 1. Push down the two buttons located at two sides of the chassis. (Fig-1) -
Page 16: Cpu Installation
GS-SR125ED System Installation Guide 5.3. CPU Installation Step 1. Please make sure the CPU type and speed that are supported by the motherboard. Step 2. To Install the CPU(s), lift up the bar that located next to the socket. (Fig-3) Figure 3 Step 3. -
Page 17: Heat Sink Installation
GS-SR125ED System Installation Guide Figure 5 Figure 6 5.4. Heat Sink Installation Step 1. Put the Heat sink on the CPU. (Fig-7) Figure 7 Figure 8 Step 2. There are for screws hold the retention modules. Seat the heat sink firmly in the retention modules with the two cooler brackets. -
Page 18: Memory Installation
GS-SR125ED System Installation Guide Step 5. Hook the other end of the cooler bracket by gripping it to another side of retention module. (Fig-9) Figure 9 5.5. Memory Installation The motherboard contains six DIMM (Dual Inline Memory Module) sockets. The systems BIOS will auto detect the size if the memory after installing. -
Page 19: Pci Expansion Card Installation
GS-SR125ED System Installation Guide 5.6. PCI Expansion Card Installation GS-SR125E provides expansion riser slots for 3 peripheral cards, Up to 100 MHz with one PCI card, up to 66 MHz with two PCI cards for full-height, Up to 100 MHz with one PCI card for Low- profile. - Page 20 GS-SR125ED System Installation Guide Step 2. Installing the PCI Riser card. To install the riser card, just simply push it into the module. (Fig-14) Figure 14 Figure 15 Step 3. Secure the card with screws. (Fig-15) Step 4. Repeat Step 2 to install another card. (Fig-16) Step 5.
-
Page 21: Reinstall Top Cover
GS-SR125ED System Installation Guide Figure 18 5.7. Reinstall Top Cover When complete the installation of the entire essential components (from subsection 5.1 to 5.7), replace the plastic air duct. This will secure the airflow is inside the chassis. Failure to do so may cause CPU and Memory over heating. -
Page 22: Dock Handle Installation
GS-SR125ED System Installation Guide 5.8. Dock Handle Installation Remove the dock handles from the package. Put two on each side of the chassis, secure with screws provided. (Fig-20 Figure 20 5.9. Hard Disk Drive Installation Step 1.Remove the dock the hard disk drive tray handle and remove the tray from the chassis Insert the hard disk drive into the tray. - Page 23 GS-SR125ED System Installation Guide Figure 22 Figure 23 Step 2. After securing the hard disk drive with the screws, hold the hard drive handle at open position, place the tray into chassis (Fig-25) and push the hard disk drive tray handle to the closed position.
-
Page 24: Appearance Of Gs-Sr125Ed
GS-SR125ED System Installation Guide 5.10. Appearance of GS-SR125ED 5.10.1. Front View of GS-SR125ED CD-ROM Disk USB & LED Manufacture Option: 3.5” FDD/4th HDD tray IDE Hot-Swap HDD 5.10.2. Rear View of GS-SR125ED PS/2 Keyboard and Mouse connectors Low-Profile Full-Height/Full Length... -
Page 25: Led Indicator Description
GS-SR125ED System Installation Guide 5.10.3. LED Indicator Description Acting Color Status Power LED Green Power On Amber Power cable plug-in Blink Green System stands by No power SYS LED Amber System is ready but degraded: some CPU Fault, DIMM Killed... - Page 26 GS-SR125EDSystem Installation Guide HDD LED: HDD LED 1 HDD LED 2 Acting Color Status HDD LED1 Off HDD idle HDD LED1 Blink Green HDD acting HDD LED2 Off HDD is normal operating * HDD LED2 On Amber HDD fail * HDD LED2 Blink Amber Rebuild * HDD LED2 On...
-
Page 27: Floppy Drive Installation (Optional)
GS-SR125ED System Installation Guide 5.11. Floppy Drive Installation (Optional) Step 1. Remove three screws on the front top cover, (Fig-26) Push down the two buttons located at two sides of the system to remove front top cover. (Follow the arrow direction shown in Fig-... - Page 28 GS-SR125ED System Installation Guide Step 3. Place the tray into chassis (Fig-30) and push the floppy disk drive tray handle to the closed position. Note: It will make “click” sound when the floppy disk drive is inserted properly Figure 30 Figure 31 Step 4.
-
Page 29: Connector Icon Description
GS-SR125ED System Installation Guide 5.12. Connector Icon Description Suggested icons Description Keyboard Mouse Parallel Port Serial Port...