Gigabyte GS-SR103 System Installation Manual
Gigabyte GS-SR103 System Installation Manual

Gigabyte GS-SR103 System Installation Manual

Rackmount server

Advertisement

Quick Links

GS-SR103 System Installation Guide
GS-SR103
Rackmount Server
System Installation Guide
1-i

Advertisement

Table of Contents
loading

Summary of Contents for Gigabyte GS-SR103

  • Page 1 GS-SR103 System Installation Guide GS-SR103 Rackmount Server System Installation Guide...
  • Page 2: Table Of Contents

    GS-SR103 System Installation Guide 1. SAFETY, CARE AND REGULATORY INFORMATION 2. INTRODUCTION 2.1. P REFACE 2.2. F EATURES 3. PACKAGE CONTENTS 3.1. C OMPONENT ONTENT 4. SYSTEM INSTALLATION PROCEDURES 4.1. C HASSIS OVER EMOVAL 4.2. CPU I NSTALLATION 4.3. H NSTALLATION 4.4.
  • Page 3: Safety, Care And Regulatory Information

    Precautions for Products With Laser Devices Observe the following precautions for laser devices: Do not open the CD-ROM drive, make adjustments, or perform procedures on a laser device other than those specified in the product’s documentation. GS-SR103 System Installation Guide...
  • Page 4 GS-SR103 System Installation Guide Only authorized service technicians should repair laser devices. Precautions for Products With Modems, Telecommunications, or Local Area Network Options Observe the following guidelines when working with options: Do not connect or use a modem or telephone during a lightning storm.
  • Page 5 GS-SR103 System Installation Guide Federal Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 6 GS-SR103 System Installation Guide Canadian Department of Communications Compliance Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada. Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B prescrites dans le règlement sur le...
  • Page 7 GS-SR103 System Installation Guide European Community Directive Conformance Statement This product is in conformity with the protection requirements of EC Council Low Voltage Directive (Safety) 73/23/EEC, EMC Directive 89/336/EEC on the approximation of the laws of the Member States relating to electro-magnetic compatibility.
  • Page 9: Introduction

    Do not apply any cleaning solutions directly to the system. 2.2. Features The Gigabyte GS-SR103 is an ultra-thin rack-optimized server that offers superior performance and scalability to your networking system. It contains the several features that provide respective performance for...
  • Page 10 GS-SR103 System Installation Guide Features Processor Supported BIOS Chipset Memory Supported Mass Storage System Dual Socket 370 for Intel FC-PGA Pentium III or other compatible processor up to 1 GHz and above 100/133MHz FSB AUTO detect CPU voltage Support Dual BIOS technology; 2M bit flash IDE#0~#3, LS120, ZIP &...
  • Page 11: Package Contents

    System Chassis Power Supply (installed) GA-6ETXDR Motherboard (installed) Slim type CD-ROM drive (installed) Slim type Floppy drive (installed) Three Hard Disk Drive Trays for GS-SR103 The CPU heat sinks Two Dock Handles, with two screws Driver & Application CD Installation Manual...
  • Page 13: System Installation Procedures

    Figure 1 Step 3. After removing the top cover, you will see a plastic air duct over the CPU and Memory. Remove the air duct to install the CPU and Memory (Fig-3). GS-SR103 System Installation Guide Figure 2 Figure 3...
  • Page 14: Cpu Installation

    GS-SR103 System Installation Guide 4.2. CPU Installation Step 1. To install Socket 370 CPU, lift up bar located next to the Socket. Then, insert Socket370 CPU inside Socket, and push the lever bar back into the original position. (Fig-4 & Fig-5) Figure 4 4.3.
  • Page 15: Pci Expansion Card Installation

    GS-SR103 System Installation Guide memory. To install memory, simply push the memory modules into the DIMM sockets. (Fig-7) Figure 7 4.5. PCI Expansion Card Installation GS SR103 provides one expansion raiser slot for a peripheral card, 64Bit/66 MHz full length. To install the peripheral, please go through the following steps.
  • Page 16: Airflow Duct Installation

    Step 5. The card is seated properly into PCI slot. (Fig-13) 4.6. Airflow Duct Installation GS-SR103 is installed a new device which called Airflow Duct. The main function of Airflow duct is the capability of driving out excessive system heat (Especially the CPU Heat). In order to maintain the system operation smoothly, please note that CPU and RAM have been installed.
  • Page 17 GS-SR103 System Installation Guide GS-SR103 is installed a new device which called Airflow Duct. The main function of Airflow duct is to raise the capability of driving out excessive system heat (Especially the CPU Heat). In order to maintain the system operation smoothly, please note that CPU and RAM are installed in advance.
  • Page 18: Reinstall Top Cover

    GS-SR103 System Installation Guide not be able to close tightly. Attention: There are pressures from both front and back end; therefore the slight pop up at middle is nature. 4.7. Reinstall Top Cover When complete the installation of the entire essential components (from subsection 4.1 to 4.6), replace the plastic air duct.
  • Page 19: Hard Disk Drive Installation

    GS-SR103 System Installation Guide Figure 18 4.9. Hard Disk Drive Installation Step 1. Pull the hard disk drive tray handle and remove the tray from the chassis (Fig-19). Insert the hard disk drive into the tray. Secure each hard disk drive with screws (Fig-20).
  • Page 20: Appearance Of Gs-Sr103

    GS-SR103 System Installation Guide 4.10. Appearance of GS-SR103 4.10.1 Front View of the GS-SR103 2 IDE ATA-100 Hot-Swap HDD support RAID 0,1 CD-ROM Drive 4.10.2 Rear View of the GS-SR103 Power Serial Port 1 IDE ATA-100 Easy-swap HDD Connector Expansion Slot USB &...
  • Page 21: Led Indicator

    Fan LED System LED HDD Power LED: HDD LED 1 HDD LED 1 HDD LED 2 HDD LED 2 Blink HDD LED 2 Blink HDD LED 2 GS-SR103 System Installation Guide Color Green Green Green Amber Acting Color Green Green Amber...
  • Page 22: Connector Icons

    GS-SR103 System Installation Guide 4.11 Connector Icons Suggested icons 4-10 Description Keyboard Mouse Parallel Port Serial Port...

Table of Contents