Related Manuals for Gigabyte GS-SR101T
Summary of Contents for Gigabyte GS-SR101T
-
Page 1: System Installation
System Installation Guide GS-SR101T 1U Rack Mount Server SYSTEM INSTALLATION GUIDE... -
Page 2: Table Of Contents
INDEX 1. INTRODUCTION 1.1. P REFACE 1.2. F EATURES 2. HARDWARE INVENTORY 3. SYSTEM INSTALLATION 3.1. C HASSIS OVER EMOVAL 3.2. P ROCESSOR NSTALLATION 3.3. F EATSINK NSTALLATION RAM I 3.4. YSTEM NSTALLATION 3.5. I NSTALLING ANDLE 3.6. R EINSTALL OVER 3.7. -
Page 3: Introduction
INTRODUCTION 1.1. Preface Using this manual will help you get the most from your Rack Mount Server. Keeping the manual with your Rack Mount Server to refer when you want information and help. In order to get the optimal usage out of your Rack Mount Server and you should remember the following: Read through all the instruction for your Rack Mount Server . - Page 4 Checking and Correction (ECC) either un-buffered or registered memory and VCM SDRAM Supports only 3.3V SDRAM DIMM Storage Controller Max 4 IDE ATA channels ( 2 x ATA-66 and 2 x ATA-100 for IDE RAID 0 or 1 ) Support front-accessible 2 hot-swap drives featuring...
- Page 5 On LAN) Adaptive fail over feature Load balance feature I/O Expansion Slot PCI raisers , 1 slot ,support 33MHz & PCI 2.2 compliant Build-in I/O ports 1 x PS/2 Keyboard port 1 x PS/2 Mouse port 1 x COM port 1 x VGA port 1 x LPT port 2 x RJ-45 ports...
- Page 6 Other Features Support Wake On LAN ( WOL ) Support External Modem Ring On Optional DOC solution for embedded Internet/Networking Applications O/S Support Windows NT ,Windows 2000 ,Linux ( RED HAT 7.0 , Netware 5.0 Chassis Dimensions Height 44.45 mm ( 1.75 In. ) Width 482.6 mm ( 19.0 In.
-
Page 7: Hardware Inventory
Hardware Inventory When you unpack your GS-SR101 Rack Mount Server, Check that all the items that you ordered are present in good condition. Review the inventory checklist below to be sure that the components and optional components that you ordered are included. If anything is miss or damage, contact your retailer as soon as possible. -
Page 9: System Installation
System Installation Note: Please remove the protection plastic cover from top and bottom side first. If not, the system heat could not spread from top and bottom side. 3.1. Chassis Cover Removal Use screwdriver to remove the two screws on the chassis top cover . -
Page 10: Processor Installation
System Installation Guide 3.2. Processor Installation To install Socket 370 CPU, lifts up bar located next to the Socket. And then insert Socket 370 CPU inside Socket, and push the lever bar back into original position. (Fig-3 & Fig-4 ) CPU-1 CPU-2 Fig-3... - Page 11 System Installation Guide Figure 4...
-
Page 12: Fan+Heatsink Installation
System Installation Guide 3.3. Fan+Heatsink Installation Click Fan+Heatsink to CPU socket 370 and plug the Fan power cable to the each CPU cooling Fan connector on the motherboard . ( Fig-5 ) Make sure the Fan wire is click on the HeatSink .( Fig-6 ) Figure 5 Figure 6... - Page 13 System Installation Guide For CPU1 ,Fan power cable connect to J13 (CPU1 FAN) connector and for CPU2, Fan power cable connect to J15 (CPU2 Fan) Connector. Note to make sure the connector is plugged into the header in the correct and click well. ( Fig-7 ) J13-CPU1 Fan Connector J15-CPU2 Fan Connector Figure 7...
-
Page 14: System Ram Installation
System Installation Guide 3.4. System RAM Installation The motherboard has 4 Dual Inline Memory Module (DIMM) sockets. The BIOS will automatically detect memory type and size. To install the memory module, just push it into the DIMM slot. (Fig-8 ) Fig-8... -
Page 15: Installing Handle
3.5. Installing Handle Get Handle and screw from the accessories box. And then mount the handle on the front panel .( Fig-9 & Fig-10 ) Fig-9 Fig-10 System Installation Guide... -
Page 16: Reinstall Top Cover
System Installation Guide 3.6. Reinstall Top Cover After the above steps (3.1 to 3.5 ) were finished then slide a top cover to a chassis (Fig-11 )and use screwdriver to reinstall the 2 screws on the top cover .( Fig-12 ) Fig-11 Fig-12... -
Page 17: Hard Disk Drive Installation
3.7. Hard Disk Drive Installation Get the quick-swap Hard Disk tray from the accessories box. And then connect the HDD data cable and Power cable to Hard Disk Drive. Note IDE data cable Red Line is make sure to connect Hard Disk Drive pin 1. (Fig-13 & Fig-14) HDD Power Cable Fig-13 HDD Data Cable Pin 1... - Page 18 After the above step, mount HDD to HDD tray with the screw ( Fig-15 ) ,and put HDD tray into the chassis .( Fig-16 ) Fig-15 Fig-16 3-10 System Installation Guide...
- Page 19 System Installation Guide When you put HDD tray into the chassis, make sure that the lever is at a 90 degree angle to the chassis .( Fig-17 ) Otherwise ,damage may occur to lever. After that push HDD tray to chassis carefully and make sure the HDD tray is click into Chassis.
- Page 20 System Installation Guide And then push lever to lock HDD tray into the chassis. (Fig-19) Fig-19 If you do not making sure that the lever is at a 90-degree angle to the Chassis ,the HDD tray click may be damage .( Fig-20 ) HDD Tray Click Fig-20 3-12...
- Page 21 System Installation Guide When you put HDD tray into the chassis ,make sure there is a no gap between HDD tray and chassis .Otherwise the system can’t detect the HDD .(Fig-21 ) Fig-21 3-13...
-
Page 22: Front Side
3.8. Front Side IDE ATA-100 Hot-swap HDD 3.9. LED Indicators Power Switch & LED HDD1 LED Power LED Green - System Power On LED Off – System Power Off 3-14 System Installation Guide Slim Type CD-ROM Slim Type FDD LAN2 LED LAN1 LED HDD2 LED Fan LED... -
Page 23: Back Side
LAN LED Green – LAN Activity LED Off – No LAN Connection Blinking – Data Access Fan Led LED Off – System Fan Normal state Orange – System Fan Crash HDD LED LED Off – System Booting (But when detect HDD the LED is orange) Green –... -
Page 24: Connector Icons
System Installation Guide 3.11. Connector Icons Description Suggested icons Keyboard Mouse Parallel Port Serial Port 3-16...