Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gigabyte GS-SR 113
Summary of Contents for Gigabyte GS-SR 113
-
Page 1: Installation Guide
GS-SR 113 Rack Mount Server System Installation Guide REV.1.0... -
Page 3: Table Of Contents
GS-SR113 System Installation Guide Contents SAFE, CARE AND REGULATORY INFORMATION PREFACE INTRODUCTION 3.1. EATURES CONTENTS PACKAGE SYSTEM INSTALLATION PROCEDURES 5.1. HASSIS EMOVAL 5.2. CPU I NSTALLATION 5.3. NSTALLATION 5.4. EMORY NSTALLATION 5.5. PCI E XPANSION NSTALLATION 5.6. NSTALLATION 5.7. EINSTALL OVER 5.8. - Page 4 GS-SR113 System Installation Guide The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to update the information contained herein. Third-party brands and names are the property of their respective owners.
-
Page 5: Safe, Care And Regulatory Information
GS-SR113 System Installation Guide 1. Safe, Care and Regulatory Information Important safety information Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. The product should be operated only from the type of power source indicated on the rating label. - Page 6 GS-SR113 System Installation Guide Precautions for Products With Laser Devices Observe the following precautions for laser devices: Do not open the CD-ROM drive, make adjustments, or perform procedures on a laser device other than those specified in the product’s documentation. Only authorized service technicians should repair laser devices.
- Page 7 GS-SR113 System Installation Guide generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
- Page 8 GS-SR113 System Installation Guide The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part 68, Sec. 68.381 (c) (3)). / for Canadian users only / Canadian Department of Communications Compliance Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada.
- Page 9 GS-SR113 System Installation Guide metallic water pipe system, if resent are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading.
-
Page 10: Preface
For your protection, please read and understand all of the safety and operating instructions regarding your Gigabyte Server and retain for future reference. The procedures in this guidebook assume that you are a system or network administrator experienced in installing similar hardware. -
Page 11: Introduction
GS-SR113 System Installation Guide 3. Introduction Welcome to the Gigabyte GS-SR113 Rack mount Server System Installation Guide. The guidebook provides instructions for configuration hardware for the GS-SR113 to your system. In order to get the optimal usage of your server, please pay... - Page 12 GS-SR113 System Installation Guide Features Description Motherboard GA-8IRXRR-D Processor Supported Supports Single Intel P4 Northwood Processor up to 2.20 Ghz and above 400MHz FSB BIOS Award BIOS on 4Mb flash RAM Multiple boot options Supports user setting for hardware monitoring Support PXE DMI 2.0 compliant Chipset...
- Page 13 GS-SR113 System Installation Guide Dual ATA100 Channels Mass Storage System Three low-profile shelves for hot- swappable drives One slim type flexible FDD drive One slim type CD-ROM drive System Form Factor 1U, ultra thin, rack-optimized design System Dimensions 19” W*23” D*1.74” H I/O expansion slots 4 full-length 32bit/33 MHz PCI slots Built-in I/O ports...
-
Page 14: Contents Package
GS-SR113 System Installation Guide 4. Contents Package When opening the package, please ensure the system components are not damaged during the shipping. Using the following checklist to verify the contents. If any component is missing or damaged in the system, please contact your vendor immediately. -
Page 15: System Installation Procedures
GS-SR113 System Installation Guide 5. System Installation Procedures Please remove the protective thin films (Top and bottom) from the system when installing. 5.1. Chassis Removal Step 1. Unscrew the two thumbscrews from the back of the system. (Fig-1) Figure 1 Figure 2 Step 2. -
Page 16: Cpu Installation
GS-SR113 System Installation Guide Figure 3 5.2. CPU Installation Step 1. Please make sure the CPU type and speed that are supported by the motherboard. Step 2. To Install the CPU, lift up the bar that located next to the socket. - Page 17 GS-SR113 System Installation Guide Figure 5 Step 4. Then, align the CPU and insert it into the socket. (Fig-6) Step 5. Push the lever back to the original position to finish the CPU installation. (Fig-7) Figure 6 Figure 7...
-
Page 18: Heat Sink Installation
GS-SR113 System Installation Guide 5.3. Heat Sink Installation Step 1. Put the Heat sink on the CPU. Figure 8 Figure 9 Step 2. Before putting the heat sink on the CPU, please well remember to apply the thermal conductivity compound on the CPU. -
Page 19: Memory Installation
GS-SR113 System Installation Guide Figure 10 5.4. Memory Installation The motherboard contains two slanted DIMM (Dual Inline Memory Module) sockets. The systems BIOS will auto detect the size if the memory after installing. To install memory, simply push the memory modules into the DIMM sockets. (Fig 11) Figure 11... -
Page 20: Pci Expansion Card Installation
GS-SR113 System Installation Guide 5.5. PCI Expansion Card Installation GS-SR113 provides one expansion riser slot for two peripheral cards, 32Bit/33 MHz full-height. To install the peripheral, please go through the following steps. Step 1. There are two screws holding the riser bracket. First, remove the screw on the top of the bracket, then, remove another screw located at the rear of the server. - Page 21 GS-SR113 System Installation Guide Step 3. Install the card into place. (Fig-15) Figure 15 Step 4. Replace the riser bracket into the PCI slot on the motherboard. Push down the bracket firmly. The card is seated properly into PCI slot. Figure 16 Step 5.
-
Page 22: Air Flow Duct Installation
GS-SR113 System Installation Guide 5.6. Air Flow Duct Installation GS-SR113 is enhanced a new device which called Airflow Duct. The main function of the airflow duct is to increase the capability of driving out the excessive system heat (Especially the CPU heat). -
Page 23: Reinstall Top Cover
GS-SR113 System Installation Guide Figure 19 Figure 19 indicates the airflow duct should be flat and completely placed into the system. When the upper case is placed, please be aware that the power supply header and the motherboard should be completely placed under the duct cover. Otherwise the upper case might not be able to close tightly. -
Page 24: Dock Handle Installation
GS-SR113 System Installation Guide Figure 20 5.8. Dock Handle Installation Remove the dock handles from the package. Put two on each side of the chassis, secure with screws provided. (Fig-21) Figure 21 5.9. Hard Disk Drive Installation Step 1. Pull the hard disk drive tray handle and remove the tray from the chassis (Fig-22). - Page 25 GS-SR113 System Installation Guide Figure 22 Figure 23 Step 2. After securing the hard disk drive with the screws, hold the hard drive handle at open position, place the tray into chassis (Fig-24) and push the hard disk drive tray handle to the closed position.
-
Page 26: Appearance Of Gs-Sr113
GS-SR113 System Installation Guide 5.10. Appearance of GS-SR113 5.10.1. Front View of GS-SR113 2 IDE ATA Hot-Swap HDD 1 Easy Swap Secondary Primary CD ROM Drive Floppy Drive USB & 5.10.2. Rear View of GS-SR113 Power Connectors Expansion... -
Page 27: Led Indicator Description
GS-SR113 System Installation Guide 5.10.3. LED Indicator Description LAN 1 LED Power LED LAN 2 LED FAN Status LED Connectors System Status LED Acting Color Status Power Green System power on System power off LAN LED Green LAN online LAN offline Blink Green LAN acting... - Page 28 GS-SR113 System Installation Guide HDD LED: HDD LED 1 HDD LED 2 Acting Color Status Condition No HDD Installed Non-RAID LED 1 Non-RAID Green HDD Installed LED 1 HDD idle Non-RAID LED 2 Blink Green HDD acting Non-RAID LED 2 No HDD installed/ RAID LED 1...
-
Page 29: Connector Icon Description
GS-SR113 System Installation Guide 5.11. Connector Icon Description Suggested icons Description Keyboard Mouse Parallel Port Serial Port...