Related Manuals for Gigabyte GS-SR157L
Summary of Contents for Gigabyte GS-SR157L
- Page 1 GS-SR157L 1U Rack Mount Server System Installation Guide Intel Pentium Prescot LGA775 Processor Serverboard ® Rev. 1001 25A080-0157L-F00...
-
Page 2: Table Of Contents
Step 3-5: PCI Expansion Card Installation ..............15 Step 3-6: Hard Disk Drive Installation ................16 Step 3-7: FAN Duct Removal and Installation .............. 17 Chapter 4 Appearance of GS-SR157L ..........18 4-1: Front View of GS-SR157L ..................18 4-2: Rear View of GS-SR157L ..................19 4-3: Switch and LED Indicators Introduction .............. - Page 3 Table of Content Chapter 6 BIOS Setup ................26 Main ......................28 Advanced Processor Options ..................31 Advanced ....................32 Memory Configuration ..................... 33 PCI Configuration ......................34 I/O Device Configuration ....................36 Advanced Chipset Control ..................... 40 Security ...................... 43 Server ......................
-
Page 4: Safety, Care And Regulatory Information
GS-SR157L Rack Mount Server Safety, Care and Regulatory Information Important safety information Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. * The product should be operated only from the type of power source indicated on the rating label. - Page 5 Safety Information * To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord. * Do not plug a modem or telephone cable into the network interface controller (NIC) receptacle. * Disconnect the modem cable before opening a product enclosure, touching or installing internal components, or touching an uninsulated modem cable or jack.
- Page 6 GS-SR157L Rack Mount Server Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect proper operation of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service.
- Page 7 Safety Information NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the sum of the Load Numbers of all the devices does not exceed 100.
-
Page 8: Contents Packages
For your protection, please read and undertand all of the safety and operating instructions regarding your Gigabyte Server and retain for future reference. The procedures in this guidebook assusme that your are a system or network administrator experienced in installing similar hardware. -
Page 9: Chapter 1 Features Summary
Feature Summary Chapter 1 Features Summary Motherboard GA-8ICXR Processor Supported Supports Intel Pentium Prescot LGA 775 processor ® Intel Prescot LGA 775 supports 800MHz FSB ® L2 cache on-die per processor from 1M Chipset Intel MCH E7221 Chipset ® Intel 6702 PXH-V ®... - Page 10 GS-SR157L Rack Mount Server Super I/O Controller ITE IT8712F-A Super I/O Built-in I/O 1 x Serial port (COM) 1 x USB 2.0 dual-port connector 1 x VGA connector 2 x RJ45 LAN ports P/S 2 Keyboard and Mouse Connectors 1 x RJ45 on front for console redirection...
-
Page 11: Chapter 2 System Overview
System Overview Chapter 2 System Overview A. Chassis Cover F. ZCR Slot B. Motehrboard - GA-8ICXR G. HDD Plate C. Heat Sink H. HDD D. System Fans I. FDD E. Riser Card Support J. Power... -
Page 12: Chapter 3 System Hardware Installation
GS-SR157L Rack Mount Server Chapter 3 System Hardware Installation Please observe the safety information in chapter “Important Safety Information” Do not expose the server to extreme environmental conditions. Protect it from dust, humidity, and heat. Step 3-1: Chassis Removal and Installation Step 1 Loosen the thumbscrew from the back of the server. -
Page 13: Step 3-2: Cpu Installation
Hardware Installation Process Step 3-2: CPU Installation Please make sure the CPU type and speed that are supported by the motherboard. Step 1 Gently lift the metal lever located on the CPU socket to the upper-right position. Step 2 Remove the plastic covering on the CPU socket. Step 3 Align the indented corner of the CPU with the triangle and gently insert the CPU into position. -
Page 14: Step 3-3: Heat Sink Installation
GS-SR157L Rack Mount Server Step 3-3: Heat Sink Installation Step 1 Place the Heat Sink on the CPU. Before putting the heat sink on the CPU, please well remember to apply the thermal conductivity compound on the CPU. Step 2 Seat the heat sink in the retention modules with the four screws. Installation completed. -
Page 15: Step 3-5: Pci Expansion Card Installation
Hardware Installation Process Step 3-5: PCI Expansion Card Installation GS-SR157L provides expansion riser slots for one PCI-X full-height/full-length 64/66~100MHz; and one with PCI-X low-profile 64-Bit/66~100MHz. To install the peripheral, please go through the following steps. Note!! Before installing the PCI expansion card, please check the card size limitation. Size limitation for PCI-X full-height/full-length is 228.5 mm x 91.5 mm;... -
Page 16: Step 3-6: Hard Disk Drive Installation
GS-SR157L Rack Mount Server Step 3-6: Hard Disk Drive Installation Step 1 Lossen the screws securing the hard drive plate. Step 2 Slide toward to remove the hard drive plate from system. Step 3 Place hard disk on the plate and lock hard drive with 4 screws. -
Page 17: Step 3-7: Fan Duct Removal And Installation
Hardware Installation Process Step 3-7: FAN Duct Removal and Installation Step 1 Pull up the screw-holder and lossen the thumbscrews. Lift up to remove the fan duct. Step 2 For FAN Duct Installation, place the fan duct on the top of heat sinks. Fasten the screws to the locked position and push down the screw-holders. -
Page 18: Chapter 4 Appearance Of Gs-Sr157L
GS-SR157L Rack Mount Server Chapter 4 Appearance of GS-SR157L 4-1: Front View of GS-SR157L... -
Page 19: 4-2: Rear View Of Gs-Sr157L
System Appearance 4-2: Rear View of GS-SR157L t r o t r o e l i f t o l l l u i s - l l u e l - t o l r o t r o t &... -
Page 20: 4-3: Switch And Led Indicators Introduction
GS-SR157L Rack Mount Server 4-3: Switch and LED Indicators Introduction HDD Fail Warning Status Power/Sleep LAN1/2 Activities Name Color Condition Description Power Green Power On Green Blink Sleep (S1) Power Off (S4/S5) Status Green System Ready On/ Alarm Amber Blink System Ready but deqraded, CPU Failed, DIMM Killed. -
Page 21: 4-4: Lan Led Description
LED Description 4-4: LAN LED Description Name Color Condition Description Green LAN Link / no Access Link/Activity Green BLINK LAN Access Idle GbE LAN Yellow 1Gbps connection Speed Yellow BLINK Port identification with 1Gbps connection Green 100Mbps connection Green BLINK Port identification with 10 or 100Mbps connection 10Mbps connection... -
Page 22: 4-5 : Connector Icon Description
GS-SR157L Rack Mount Server 4-5 : Connector Icon Description i r c i t p l e l l a i... -
Page 23: Chapter 5 Motherboard Layout & Jumper Setting
Motherboard Layout Chapter 5 Motherboard Layout & Jumper Setting 5-1: GA-8ICXR Motherboard Layout... - Page 24 GS-SR157L Rack Mount Server CPU LGA775 IPMB1 Intel MCH E7221 IPMB2 Intel 6702 PXH-V PCI1 IntelICH6R PCI_X1 DDR1 IDE1 DDR2 SATA1 DDR3 SATA2 DDR4 SATA3 SATA4 Front Panel IPMBI Intel 82541PI USB2 COM2 FAN1 FAN2 FAN3 FAN4 FAN5 FAN6 FAN7...
-
Page 25: 5-2: Jumper Setting
Jumper Setting 5-2: Jumper Setting CLR_CMOS ( (Clear CMOS Function) You may clear the CMOS data to its default values by this jumper. Default value doesn’t include the “Shunter” to prevent from improper use this jumper. To clear CMOS, temporarily short 1-2 pin. 1-2 close: Clear CMOS 2-3 close: Normal (Default value) -
Page 26: Chapter 6 Bios Setup
GS-SR157L Rack Mount Server Chapter 6 BIOS Setup BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. -
Page 27: Getting Help
BIOS Setup GETTING HELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. -
Page 28: Main
GS-SR157L Rack Mount Server Main Once you enter Phoenix BIOS Setup Utility, the Main Menu (Figure 1) will appear on the screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. Figure 1: Main System Time The time is calculated based on the 24-hour military time clock. -
Page 29: Legacy Diskette A
BIOS Setup Legacy Diskette A This category identifies the type of floppy disk drive A that has been installed in the computer. Disabled Disable this device. 360KB, 5 inch AT-type high-density drive; 360K byte capacity 1.2MB, 3 inch AT-type high-density drive; 1.2M byte capacity 720K, 3 inch double-sided drive;... - Page 30 BIOS Setup TYPE 1-39: Predefined types. Users: Set parameters by User. Auto: Set parameters automatically. (Default Vaules) CD-ROM: Use for ATAPI CD-ROM drives or double click [Auto] to set all HDD parameters automatically. ATAPI Removable: Removable disk drive is installed here. Multi-Sector Transfer This field displays the information of Multi-Sector Transfer Mode.
-
Page 31: Advanced Processor Options
BIOS Setup Advanced Processor Options Figure 1-1: Advanced Processor Options Advanced Processor Option This category includes the information of CPU Speed, Processor ID, Processor L2 Cache. Hyper Threading Technology Enabled Enables Hyper-Threading Technology Feature when using Windows XP and Linux 2.4x operating systems that are optimized for Hyper- Threading technology. -
Page 32: Advanced
GS-SR157L Rack Mount Server Advanced About This Section: Advanced With this section, allowing user to configure your system for basic operation. User can change the processor options, chipset configuration, PCI configuration and chipset control. Figure 2: Advanced... -
Page 33: Memory Configuration
BIOS Setup Memory Configuration Figure 2-1: Memory Configuration System Memory/Extended Memory/DIMM Group 1,2,3,4 Status These category is display-only which is determined by POST (Power On Self Test) of the BIOS. Memory Reset Select ‘Yes’, system will clear the memory error status. Disable this function. -
Page 34: Pci Configuration
GS-SR157L Rack Mount Server PCI Configuration Figure 2-2: PCI Configuration Embedded Video Controller Onboard VGA Control Enabled Enable onboard VGA device. (Default value) Disabled Disable this function. Pre-Allocated Memory Size Select the amount of pre-allocated graphics memory for use by the Internal Graphics Device. - Page 35 BIOS Setup Embedded NIC #1 Onboard LAN1 Control Enabled Enable onboard LAN1 device. (Default value) Disabled Disable this function. Option ROM Scan Enabled Enableing this item to initialize device expansion ROM. Disabled Disable this function. (Defualt value) Embedded NIC #2 Onboard LAN2 Control Enabled Enable onboard LAN2 device.
-
Page 36: I/O Device Configuration
GS-SR157L Rack Mount Server I/O Device Configuration Figure 2-3: I/O Device Configuration... -
Page 37: Serial Port A
BIOS Setup Serial Port A This allows users to configure serial prot A by using this option. Disabled Disable the configuration. Enabled Enable the configuration (Default value) Serial Port B This allows users to configure serial prot B by using this option. Disabled Disable the configuration. -
Page 38: Legacy Usb Support
GS-SR157L Rack Mount Server USB 2.0 Controller This item allows users to enable or disable the USB 2.0 device by setting item to the desired value. Enabled Enable USB 2.0 controller. (Default value) Options Disbale this function. Legacy USB Support This option allows user to function support for legacy USB. - Page 39 BIOS Setup SATA AHCI Enable Enabled Set this item to enable SATA AHCI function for WinXP-SP1+IAA driver supports AHCI mode. Disabled Disabled this function. SATA RAID Enable Enabled Enabled SATA RAID function. Disabled Disable this function.
-
Page 40: Advanced Chipset Control
GS-SR157L Rack Mount Server Advanced Chipset Control Figure 2-4: Advanced Chipset Control Wake On LAN / PME This option allow user to determine the action of the system when a LAN/PME wake up event occurs. Enabled Enable Wake On LAN/PME. (Default value) Disabled Disable this function. -
Page 41: Wake On Ring
BIOS Setup Wake On Ring This option allow user to determine the action of the system power is off and the modem is ringing. Enabled Enable Wake On Ring. (Default value) Disabled Disable this function. Note: This item must enabled if you’re running under Windows operating system. Wake On RTC Alarm You can set "RTC Alarm Resume"... - Page 42 GS-SR157L Rack Mount Server Memory Processor Error When Boot is selected, the system will attempt to boot after a memory or proocessor error occured. System attempts to boot if a memory or proocessor error cooured. Boot (Default value) Halt System will stop if an error is detected during power up.
-
Page 43: Security
BIOS Setup Security Figure 3: Security About This Section: Security In this section, user can set either supervisor or user passwords, or both for different level of password securities. In addition, user also can set the virus protection for boot sector. Set Supervisor Password You can install and change this options for the setup menus. -
Page 44: Diskette Access
GS-SR157L Rack Mount Server Set User Password You can only enter but do not have the right to change the options of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password. -
Page 45: Server
BIOS Setup Server Figure 4: Server... - Page 46 GS-SR157L Rack Mount Server Please note that when the main board is inserted the IPMI card, the Server menu will show as below: When IPMI cardi is installed, screen will display the information of the card during system boots.
- Page 47 BIOS Setup Event Log Confuguration This option contains additional setup menu to configure the Event Log Configuration. Clear all Event Logs Enter The system event log will be cleared if pressing Enter. Log Post System Event Enabled Enable Log Post System Event. Disabled Disable this option.
-
Page 48: System Management
GS-SR157L Rack Mount Server System Management Figure 4-1: System Management Server Management This category allows user to view the server management features. Including information of BIOS Version. All items in this menu cannot be modified in user’s mode. If any items require... -
Page 49: Console Redirection
BIOS Setup Console Redirection Figure 4-2: Console Redirection BIOS Redirection Port If this option is set to enabled, it will use a port on the motherboard. On-board COMA Use COMA as he COM port address. Disabled Disable this function. (Default value) Note: Tower has COMA and COMB. -
Page 50: Terminal Type
GS-SR157L Rack Mount Server Terminal Type This option allows user to select the specified terminal type. This is defined by IEEE. Options VT100, VT100 8bit, PC-ANSI 7bit, VT100+, VT-UTF8 Flow Control This option provide user to enable the flow control function. - Page 51 BIOS Setup Assert NMI on SERR If thisoption is set to enabled, PCI bus system error (SERR) is enabled and is routed to NMI. Enabled Enable Assert NMI on SERR. (Default value) Disabled Disable this function. Post Error Pause If this item is set to enabled, the system will wai for user intervention on critical POST errors. If this item is disabled, the system will boot with no inten=rvention if possible.
-
Page 52: Boot
GS-SR157L Rack Mount Server Boot Figure 5: Boot About This Section: Boot The “Boot” menu allows user to select among four possible types of boot devices listed using the up and down arrow keys. By applying <+> and <Space> key, you can promote devices and by using the <->... -
Page 53: Exit
BIOS Setup Exit Figure 6: Exit About This Section: Exit Once you have changed all of the set values in the BIOS setup, you should save your chnages and exit BIOS setup program. Select “Exit” from the menu bar, to display the following sub-menu. Exit Saving Changes Exit Discarding Changes Load Settup Default... -
Page 54: Exit Discarding Changes
GS-SR157L Rack Mount Server Exit Saving Changes This option allows user to exit system setup with saving the changes. Press <Enter> on this item to ask for the following confirmation message: Pressing ‘Y’ to store all the present setting values tha user made in this time into CMOS. - Page 55 BIOS Setup Discard Changes This option allows user to load previos values from CMOS for all setup item. When you press <Enter> on this item, you will get a confirmation dialog box with a message as below: Setup Confirmation Load previous configuration now? [Yes] [No] Save Changes...
-
Page 56: 7-1: Acronyms
GS-SR157L Rack Mount Server Chapter 7 Appendix 7-1: Acronyms Acronyms Meaning ACPI Advanced Configuration and Power Interface Advanced Power Management Accelerated Graphics Port Audio Modem Riser Advanced Communications Riser BIOS Boot Specification BIOS Basic Input / Output System Central Processing Unit... - Page 57 Appexdix Acronyms Meaning Input / Output IOAPIC Input Output Advanced Programmable Input Controller Industry Standard Architecture Local Area Network Logical Block Addressing Light Emitting Diode Megahertz MIDI Musical Instrument Digital Interface Memory Translator Hub Memory Protocol Translator Network Interface Card Operating System Original Equipment Manufacturer PCI A.G.P.