Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Gigabyte GS-SR104
Summary of Contents for Gigabyte GS-SR104
-
Page 1: System Installation
System installation Guide GS-SR104 Rack Mount Server System Installation Guide... -
Page 2: Table Of Contents
System installation Guide INDEX 1. INTRODUCTION 1.1. P REFACE 1.2. F EATURES 2. HARDWARE INVENTORY 3. SYSTEM INSTALLATION PROCEDURES 3.1. C HASSIS OVER EMOVAL 3.2. CPU I NSTALLATION 3.3. H NSTALLATION 3.4. M EMORY NSTALLATION 3.5. H RIVE NSTALLATION 3.6. PCI E XPANSION NSTALLATION 3.7. -
Page 3: Introduction
System installation Guide 1. INTRODUCTION 1.1. Preface Using this manual will help you get the most from your Rack Mount Server. Keeping the manual with your Rack Mount Server to refer when you want information and help. In order to get the optimal usage out of your Rack Mount Server and you should Remember the following: Read through all the instruction for your Rack... - Page 4 System installation Guide AUTO detect CPU voltage BIOS Award BIOS 2M bit flash ROM Auto configure IDE HDD type Multiple boot options User setting for hardware monitoring DMI 2.0 compliant Chipset VIA Apollo Pro Family AGP set ( VT82C694T ,VT82C686B ) Chipset ATI Rage XL VGA Chip with 8MB Video Memory Intel 82559 Dual LAN chip...
- Page 5 System installation Guide I/O Expansion Slot PCI riser , 1 slot ,support 33MHz & PCI 2.2 compliant Build-in I/O ports 1 x PS/2 Keyboard port 1 x PS/2 Mouse port 2 x COM port ( 1 x back side and 1 x front side ) 1 x VGA port 1 x LPT port 2 x RJ-45 ports...
-
Page 7: Hardware Inventory
System installation Guide 2. Hardware Inventory When you unpack your GS-SR104 Rack Mount Server ,Check that all the items that you ordered are present in good condition. Review the inventory checklist below to be sure that the components and optional components that you ordered are included. If anything is miss or damage ,contact your retailer as soon as possible. -
Page 9: System Installation Procedures
System installation Guide 3. System Installation Procedures Warning: Please remove the protective thin films (Top and Bottom) from the system when installing. 3.1. Chassis Cover Removal Unscrew the two thumbscrews from top cover of the system (Fig-1). Standing at the front of the system. Gently apply force to the indentures with your thumbs and push toward the rear of the chassis for about 3/4 of an inch. -
Page 10: Cpu Installation
System installation Guide Fig-3 3.2. CPU Installation Lift the ZIF (Zero Insertion Force) socket lever up 90 degree. Insert CPU into the socket. Make sure CPU is seated properly, then push the level back to the original locked position. (Fig-4 and Fig-5 ) Fig-4 Fig-5... -
Page 11: Memory Installation
System installation Guide Fig-6 3.4. Memory Installation The motherboard contains four slanted DIMM (Dual Inline Memory Module) sockets. The system BIOS will auto detect the size of the memory. To install memory simply push the memory modules into the DIMM sockets. (Fig-7) After that re-install a plastic air duct into system .( Fig-8 ) Fig-7... - Page 12 System installation Guide cable plate.(Fig-9) And then remove the screw from Hard Disk Plate.( Fig-10 ) Fig-9 Fig-10 Fig-11 Fig-12 Carefully remove the Hard Disk Plate from system . (Fig-11). Put Hard Disk Drive on to Hard Disk Plate and secure each hard disk drive with screws .
-
Page 13: Pci Expansion Card Installation
. ( Fig-16 ) Fig-15 Fig-16 3.6. PCI Expansion Card Installation GS-SR104 provides two PCI slot on the one expansion raiser card for a peripheral card . One PCI slot supports standard PCI card and other slot for low profile PCI card . - Page 14 System installation Guide Attention : GS-SR104 low profile slot only provides MD1 form factor [ length : 121.79mm ( 4.795 inch ) and width : 58.09mm( 2.287inch ) ] First, remove the screws located at the rear . ( Fig-17 & Fig-18 )
-
Page 15: Reinstall Top Cover
System installation Guide 3.7. Reinstall Top Cover When you are finish installing all the essential components from above step , re-install the top cover to the system .( Fig-21 ) And then secure with screws from top side . ( Fig-22 ) Fig-21 Fig-22 3.8. -
Page 16: Front Panel
System installation Guide 3.9. Front Panel LCD Module Connector Slim CD-ROM Fig-24 3.5” FDD COM 2 LED Panel LAN 1 Status LAN 2 Status FAN Status HDD Status Fig-25 Power LED： Green－Online Off－Offline LAN LED ：Green－Online Off－Offline Flashing－LAN Activity Fan LED ： Orange－ Fan fail Off－Normal HDD LED ：... -
Page 17: Rear Panel
System installation Guide 3.10. Rear Panel 32bit/33MHz PCI Slot ( Low Profile ) Parallel Port PS/2 Mouse Fig-26 PS/2 K/B LAN 1 LAN 2 32bit/33MHz PCI COM 1 Slot ( Full Size ) 3.10.1. LCD Module Installation (Optional ) LCD module including LCD module ‘ locker and screw . -
Page 18: Lcd Module Setting Instruction
System installation Guide Fig-27 Fig-28 And then LCD module cable connect to system connector . ( Fig- 29 ) After that install the LCD module and secure with screw . ( Fig-30 ) Fig-29 Fig-30 3.10.2. LCD Module Setting Instruction The Up arrow button for menu selection and increase the digit number and character located at the cursor position . -
Page 19: Lcd Display Information
System installation Guide The Down arrow button for menu selection and decreases the digit number and character located at the cursor position . The Right arrow button moves the cursor to the right . The Left arrow button moves the cursor to the left . -
Page 20: Using The Lcd Module
System installation Guide 3.10.4. Using the LCD module LCD module serves following purposes ; ( 1 ) Configure the LAN 1 IP address ‘ Netmask and Gateway . ( 2 ) Configure the LAN 2 IP address ‘ Netmask and Gateway . ( 3 ) Display time setting ( Default 2 sec ) ( 4 ) Display information menu : user can setting which information will be show or not . -
Page 21: Connector Icons
System installation Guide 3.11. Connector Icons Suggested icons Description Keyboard Mouse Parallel Port Serial Port 3-13...