Ricoh AP600N Setup Manual page 101

Note to users in the United States of America
Notice:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular instal-
lation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio /TV technician for help.
Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment.
Caution (in case of 100BaseTX environment):
Properly shielded cables must be used for connections to host computer (and/or peripheral) in order to meet FCC emission limits.
Network interface cable with ferrite core must be used for RF interference suppression.
Declaration of Conformity
Product Name: Laser Printer
Model Number: Aficio AP600N/MLP32/P7132n/LP032
Responsible party: Ricoh Corporation
Address: 5 Dedrick Place, West Caldwell, NJ 07006
Telephone number: 973-882-2000
This device complies with part 15 of FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received,
including interference that may cause undesired operation.
Properly shielded cables must be used for connections to host computer (and/or peripheral) in order to meet FCC
emission limits.
Network interface cable with ferrite core must be used for RF interference suppression.
Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé à l'in-
térieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal. Si le matériel (ou son an-
tenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
Note to users in Canada
Note:
This Class B digital apparatus complies with Canadian ICES-003.
Remarque concernant les utilisateurs au Canada
Avertissement:
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
1. Properly shielded and grounded cables and connectors must be used for connections to host computer (and/or peripheral) in
order to meet FCC emission limits.
2. AC adapter with ferrite core must be used for RF interference suppression.
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
a means POWER ON. a
a a
b means POWER OFF. b b b
Notice to Wireless LAN Interface (option) Users: 802.11b Interface Unit Type A
Notes to users
It is strictly forbidden to use antenna(s) except designated.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm (8 inches) from all per-
sons and must not be located near other antennas or transmitters.
Notes to users in the United States of America
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment.
802.11b Interface Unit TypeA (R-WL11):
This device complies with RSS 210 of Industry Canada.
To prevent radio interference to the licensed service, this device must be operated indoors only and should be kept away from win-
dows to provide maximum shielding.
Note to users in Canada
This device complies with RSS-210 of Industry Canada.
The term " IC: " before the certification/registration number only signifies that the Industry Canada technical specifications were met.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to pro-
vide maximum shielding.
Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference, including interference that may
cause undesired operation.
Remarque concernant les utilisateurs au Canada
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada.
L'expression << IC: >> avant le numéro d'homologation/enregistrement signifie seulement que les spécifications techniques d'In-
dustrie Canada ont été respectées.
Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé à l'intérieur et devrait
être placé loin des fenêtres afin de fournir un écran de blindage maximal.
Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'utilisation de ce dispositif est autorisée seulement aux conditions suivantes:
(1)il ne doit pas produire de brouillage et (2) l'utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu,
même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
802.11b Interface Unit TypeA(R-WL11):
Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé à l'intérieur et devrait
être placé loin des fenêtres afin de fournir un écran de blindage maximal. Si le matériel (ou son antenne d'émission) est installé à
l'extérieur, il doit faire l'objet d'une licence.
Copyright © 2003