Convenient Functions; Testing Speaker Output/Adjusting Speaker Volumes - Panasonic SC-ELS10 Operating Instructions Manual

Convenient functions

RECEIVER
AV
SYSTEM
RECORDER
TV DVD
TUNER PLAYER
CD VCR BD/DVD
BAND ANALOG 6CH
CH
VOLUME
0
DIRECT
TUNING
DISC ENTER
XM CAT XM CH
SKIP SLOW/SEARCH
STOP PAUSE PLAY
DRIVE SELECT CM SKIP
ENTER
SUB MENU RETURN
XM DISPLAY
SUBWOOFER TV
OFF DIMMER
EFFECT VOL
LEVEL
NEO : 6 TV/VIDEO
SFC AUTO
MUSIC MOVIE TEST MUTING
34
RQT8979
SPEAKERS
A B
AUTO DETECTOR
n On the remote control
Testing speaker
output/Adjusting
speaker volumes
How speakers are
displayed
L : Front left
C :
Center
R : Front right
RS : Surround right
LS : Surround left
SBR : Surround back right
SBL : Surround back left
SB : Surround back
(If you connect one
surround back
speaker)
SW (SUBW ) : Subwoofer
C
C
INPUT SELECTOR
BI-AMP SURROUND
ADVANCED DUAL AMP WIRELESS READY MULTI ROOM
POWER
-MENU/-SETUP ENTER SURROUND SPEAKERS TUNE
RETURN AUTO DETECTOR -MULTI ROOM
- MENU/ - SETUP ENTER
SURROUND SPEAKERS TUNE
RETURN -
AUTO DETECTOR MULTI ROOM
• Confirm audio output using the test signal after speakers are set.
• Adjust the output of the center and surround speakers, etc. to
balance front speaker sounds with those from each of the other
speakers in the seating area.
• You can adjust the speaker output according to your preference during playback.
Press [SPEAKERS A] on the unit to switch "
(Press [SPEAKERS A] or [SPEAKERS B] to switch "
on when bi-wire speakers are connected.)
AUTO
1 Press
TEST
• A test signal is output from one speaker at a
time for two seconds in the following order.
L C R RS SBR
L C R RS
"SBR " and "SBL " are displayed when the surround back speakers
are connected. ("SB " is displayed in case of one speaker.)
VOLUME
2 Press to adjust the volumes of front
speakers to the normal listening level.
To finish after confirming the speaker output
Press [TEST, –AUTO] to stop the test signal.
To adjust speaker volumes
Go to step 3.
LEVEL
3 Press to select a speaker for
adjustment.
Speakers switch in the following order each time
you press the button.
RS SBR SBL
RS SB
"SBR " and "SBL " are displayed when the surround back speakers
are connected. ("SB " is displayed in case of one speaker.)
4 Press to adjust the
volume of the selected speaker.
Repeat steps 3 and 4 to adjust the
level of each speaker.
• Only the adjusted speaker produces the test
signal in steps 3 and 4.
• Connected speakers start producing the test signal
again in the above order 2 seconds after both steps.
AUTO
5 Press to stop the test signal.
TEST
Note
• You cannot adjust the level of front speakers themselves.
• Speakers not connected (á pages 13 and 23) or set as unconnected in "Setting
speakers and their sizes" (á page 39) do not output test signals.
• Check connections and perform the auto speaker setup once again when
a connected speaker does not output the test signal (á pages 26 and 27).
• If you select "SPEAKERS B" only, the test signal will not be output.
VOLUME
AUTO SPEAKER SETUP HDMI
SETUP MIC
AUX
W
- -
S VIDEO VIDEO L AUDIO R SETUP MIC W
AUX
" on.
A
A
SBL LS SW
SB LS SW
Volume range:
- - dB (minimum),
-79dB to 0dB
(maximum)
Speaker
LS SUBW
LS SUBW
Adjustment range:
–20dB to +10dB
Factory setting: 0dB
SUBW only:
MIN (minimum)
↔
29
Factory setting: 20
"
B
Speaker
↔
1 to
MAX (maximum)