Stiga MCS 470 Li 60 Series Operator's Manual page 111

6.4.1 Grass cutting
1. Start moving forward and mowing in the grass area.
2. Regulate the forward speed and the cutting
height (par. 5.4) considering the conditions of
the lawn (the height, density and dampness of
the grass) and the amount of grass collected.
3. The appearance of the lawn will improve
if you alternate cutting in both directions
at the same height (Fig.10).
In the models with forward speed
adjustment (Fig.6.B): We recommend not
to work land that slopes more than 15°.
A machine that is equipped with a MULCHING system cuts
the grass, chops it then distributes it over the lawn. It is not
necessary to collect the cut grass.
For best MULCHING results, proceed as follows:
1. Always avoid removing a large quantity of
grass. Never cut more than one third of the
total grass height per single pass (Fig.11).
2. Keep the chassis perfectly clean (par. 7.3.2).
3. Always use well sharpened cutting means.
4. Avoid mowing wet grass. It accumulates more
easily under the body shell and the mowing
performance decreases considerably.
6.4.2 Suggestions for maintaining a nice lawn
• To keep a lawn green and soft with a good appearance,
it should be cut regularly. A lawn can be composed of
different types of grass. If the lawn is cut frequently,
grass and roots grow more vigorously, forming a solid
grassy bed. If the lawn is cut is less frequently, higher
grass and weeds start growing (clover and daisies,
etc.). The frequency of mowing should be in relation
to the rate of growth of the grass, which should not be
left to grow too much between one cut and the next.
• The best height of the grass on a well-kept lawn
is approx. 4-5 cm. and with one mowing, you do
not need to remove more than a third of the total
height. If the grass is very tall, it should be cut
twice in a twenty-four hour period. The first time
with the cutting means at maximum cutting height
and the second cut at the height desired.
• Cutting too low tears and uproots the grass,
giving it a "spotted" appearance.
• During hot and dry periods, the grass should be cut a
little higher to prevent the ground from drying out.
• It is always better to cut the grass when dry. Do
not cut wet grass; this could reduce cutting means
efficiency due to sticky grass and tear the lawn.
• The cutting means must be in good condition and well
sharpened so that the grass is cut straight without a
ragged edge that leads to yellowing at the ends.
6.5 STOP
To stop the machine:
1. Release the control lever (Fig.12.A).
2. Wait until the cutting means stop.
When you have stopped the machine, it will take a
few seconds for the cutting means to stop.
IMPORTANT Always stop the machine.
• When moving between work areas.
• When driving on grass free surfaces.
• Every time it is necessary to overcome an obstacle.
• Before adjusting the cutting height.
6.6 AFTER OPERATION
1. Stop the machine (par. 6.5).
2. Open the battery housing hatch and remove the
safety key (Fig. 13.A).
3. Press the flap in the battery housing (Fig.13.B)
and remove the battery (Fig.13.C).
4. Recharge it (par 7.2.3).
5. Allow the motor to cool before sto-
ring in an enclosed space.
6. Clean (par. 7.3).
7. Check there are no loose or damaged compo-
nents. If necessary, replace the damaged com-
ponents and tighten any screws and loose bolts
or contact the authorised service centre.
IMPORTANT Remove the safe key whenever
the machine is unused or left unattended.
7. ROUTINE MAINTENANCE
7.1 GENERAL INFORMATION
The safety regulations to follow are described in
chap. 2. Strictly comply with these indications to avoid
serious risks or dangers.
Before conducting any inspections, cleaning or
maintenance/adjustment interventions on the machine:
• Stop the machine.
• Remove the safety key, (never leave the
key in the ignition or within reach of
children or unauthorised persons).
• Remove the battery.
• Make sure that all moving parts have
come to a complete stop.
• Allow the motor to cool before
storing in an enclosed space.
• Read the relevant instructions.
• Use suitable clothing, protective
gloves and goggles.
• The frequency and types of maintenance are
summarised in the "Maintenance Table". The
table will help you maintain your machine's
safety and performance. It summarises the main
interventions to be made and the frequency
applicable to each of them. Carry out the relevant
intervention according to the first deadline.
• The use of non-genuine and/or incorrectly
assembled spare parts and attachments could
adversely affect machine operation and safety. The
manufacturer shall decline all liability in the event
of injuries or damages caused by such parts.
EN - 7