1. Manuals
  2. Brands
  3. Taiwan Commate Computer Inc. Manuals
  4. Computer Hardware
  5. S630MA
  6. Quick installation

Taiwan Commate Computer Inc. S630MA Quick Installation

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
S630MA Quick Installation Chart
For your convenience, this chart lists all the CPUs supported by S630MA and their corresponding jumper
setting.
*** The Ratio of some latest CPUs are fixed by Intel, such as Celeron/ Celeron-II/ Pentium-III 366, 400, 566...
etc. You can ignore the four jumpers if you have this CPU on board and it will be auto detected by
motherboard. Please check with the CPU manufacturer or vendor for the CPU Ratio information.
　
　
　
　
　
Trademarks
Intel, Celeron , Socket 370 and Pentium III are trademarks of Intel Corporation
Ratio
JF0
JF1
3.0x
2-3
3.5x
2-3
4.0x
2-3
4.5x
2-3
5.0x
2-3
5.5x
2-3
6.0x
1-2
6.5x
1-2
7.0x
1-2
7.5x
1-2
8.0x
1-2
S630MA
Motherboard
User's Manual
Product Name: S630MA
Manual Revision: English, 1.0
JF2
JF3
2-3
2-3
1-2
1-2
2-3
1-2
2-3
1-2
2-3
1-2
1-2
2-3
2-3
1-2
1-2
1-2
1-2
1-2
2-3
2-3
2-3
1-2
2-3
2-3
2-3
2-3
1-2
1-2
2-3
1-2
2-3
1-2
2-3

Advertisement

Table of Contents
loading

Related Manuals for Taiwan Commate Computer Inc. S630MA

Summary of Contents for Taiwan Commate Computer Inc. S630MA

  • Page 1 S630MA Quick Installation Chart For your convenience, this chart lists all the CPUs supported by S630MA and their corresponding jumper setting. *** The Ratio of some latest CPUs are fixed by Intel, such as Celeron/ Celeron-II/ Pentium-III 366, 400, 566…...

  • Page 2: Table Of Contents

    SiS is a registered trademark of Silicon Integrated Systems Corp. Award is a trademark of Award Software International Inc. MS-DOS, Windows 95, Windows 98, Windows 2000 and Windows NT are registered trademarks of Microsoft Corporation Novell is a trademark of Novell Corporation ADI is a trademarks of Analog Devices Inc., All other brand and product names are trademarks or registered trademarks of their respective companies.

  • Page 3: Product Overview

    Chapter 1. Introduction 1.1 Product Overview Thank you for purchasing the S630MA motherboard. This motherboard uses SiS 630E Host Interface Controller, 2D/3D Ultra-AGP with super south single chipset. We have conducted a motherboard compatibility test with a variety of hardware and software, such as CPUs, memory, display cards, CD ROMs, Novell, MS Office ..etc and compliance with Year 2000.
  • Page 4 Full 2D/3D/DirectX acceleration. Supports hardware DVD Accelerator. Shared System Memory Area up to 64MB. LAN : Integrated 10/100Mb Fast Ethernet Controller. Full Duplex and Half Duplex Mode for both 10 and 100 Mbps. Plug and Play Compatible. High performance 32bit PCI Bus Master Architecture with integrated direct memory. IEEE 802.3 and 802.3u standard compatible.
  • Page 5 Audio Amp Power Down Signal Extended 6-bit Master Volume Control DSP 16-bit Serial Port Format, Slot 16 Mode Split Power Supplies ( 3.3V Digital / 5V Analog ) IR Port : One IrDA/ASKIR compatible Infrared interface port. (Cable optional) Expansion Slots: Three 32-bit PCI expansion slots One Audio Modem Riser (AMR ) slot Operating System :...

  • Page 6: Chapter 2. Hardware Setup

    Chapter 2. Hardware Setup 2.1 Installation Procedure Jumper settings Installation of CPU Installation of Memory I/O Connections & Panel Connections 2.1.1 Jumper Settings In this manual, (1-2) represents the first and second pins of the jumper. (2-3) represents the second and third pins of the jumper. On the motherboard, you will see two sets of jumpers with different color jumper caps: 　...

  • Page 7: Clearing The Cmos

    Ground your self with either a properly installed grounding strap or by touching a major electrical appliance long enough to discharge the static. 2.1.2 Clearing the CMOS (Yellow Jumper Cap) JRTC: CMOS Function Selection 1-2 : Clear data 2-3 : Normal Operation (Default Setting) 　...

  • Page 8: Installation Of Cpu

    5.5x 6.0x 6.5x 7.0x 7.5x 8.0x 　 The Ratio of some latest CPUs are fixed by Intel, such as Celeron/ Celeron-II/ Pentium-III 366, 400, 566… etc. You can ignore the four jumpers if you have this CPU on board and it will be auto detected by motherboard. Please check with the CPU manufacturer or vendor for the CPU Ratio information.

  • Page 9: Atx Power Connector

    ATXPWR ATX Power Connector CPUFAN CPU fan connector SYSFAN Chassis fan connector Infrared Connector ( Cable optional ) FLOPPY Floppy Disk Drive Connector IDE1, 2 Primary/ Secondary IDE Connectors PS/2 Mouse Port PS/2 Keyboard Connector VGA output Connector Serial Ports 1 & 2 COM1,COM2 Printer Port USB Connector...

  • Page 10: Floppy Disk Drive Connector

    " " module onto Infrared connector and configure the setting through UART Mode Select in Integrated Peripherals to select whether UART is directed for use with COM2 or Infrared. 2.4.4 Floppy Disk Drive Connector (34-pin FLOPPY) This connector supports the provided floppy disk drive ribbon cable. Orient the red stripe to pin 1 2.4.5 Primary/Secondary IDE Connector (Two 40-pin IDE) These connectors support the provided IDE hard disk ribbon cable.

  • Page 11: Ps/2 Keyboard Connector

    Integrated Peripherals of the CMOS SETUP UTILITY. 2.4.12 USB Connectors (4-pin USB & 5-pin JP12, JP13) S630MA provides five USB ports. You can attach USB devices to the USB connector. 2.4.13 Game/MIDI/Line Out/Line In/Microphone In Connector (optional) The connector is same as audio port of the back I/O panel. The cable is optional.

  • Page 12: Line Out Connector

    2.4.14 Line Out Connector The Line Out phonejack provides the audio outputs for the left and right stereo channels. 2.4.15 Line In Connector The Line In phonejack is used to attach monaural or stereo devices such as a cassette, Digital Audio Tape, or Minidisc players for playback, mixing, or recording.
  • Page 13 >Standard CMOS Features >Frequency Control >Advanced BIOS Features Load Fail-Safe Defaults >Advanced Chipset Features Load Optimized Defaults >Integrated Peripherals Set Password >Power Management Setup Save & Exit Setup >PnP / PCI Configurations Exit Without Saving >PC Health Status ¯ ® ¬ : Select Item Esc : Quit F10 : Save &...

  • Page 14: Advanced Bios Features Setup

    To assign the system time, the format is "hh:mm:ss". The setting is in military time. When entering 2:34pm enter "14:34:00". 3.2.3 Hard Disks Setting The BIOS supports Dual-Channel PIO and PCI Bus Master IDE ports. Each port supports one master and one slave hard drive.
  • Page 15 Figure 3-3. Advanced BIOS Features Screen CMOS Setup Utility - Copyright ( C ) 1984 - 2000 Award Software Advanced BIOS Features Virus Warning Disabled Item Help CPU Internal Cache Enabled External Cache Enabled Menu Level > CPU L2 Cache ECC Checking Enabled Processor Number Feature Disabled...
  • Page 16 device. 3.3.7 Swap Floppy Drive When enabled, physical drive A will be assigned to logical drive B, and physical drive B will be assigned to logical drive A. 3.3.8 Boot Up Floppy Seek The system will detect and verify operation of the floppy drive type. 3.3.9 Boot Up Numlock Status The option allows the <NumLock>...

  • Page 17: Advanced Chipset Features Setup

    3.3.18 Video BIOS Shadow Video shadow copies BIOS code from slower ROM to faster RAM. BIOS can then execute from RAM. 3.4 Advanced Chipset Features Setup These settings are intended for the Advanced Chipset function on the motherboard. Fine tuning these options, enhances the performance of the system.
  • Page 18 The RAS Recharge means the timing to inactive RAS and the timing for DRAM to do Recharge before next RAS can be issued. 3.4.4 RAS to CAS Delay These are timing of SDRAM CAS Latency and RAS to CAS Delay, calculated by clocks. They are important parameters affects SDRAM performance.

  • Page 19: Integrated Peripherals

    Choose 4, 8, 16, 32, 64, 128, 256MB. Memory-mapped, graphics data structures can reside in the Graphics Aperture. 3.4.13 Graphic Window WR Combin Use this item to enable or disable data combination from buffer then write to memory feature. 3.4.14 Concurrent function (MEM) & (PCI) Use these items to enable or disable concurrent memory/PCI and CPU action.
  • Page 20 　 　 　 ¯ ® ¬: Move Enter : Select +/-/PU/PD : Value F10 : Save ESC : Exit F1 : General Help F5 : Previous Value F6 : Fail-Safe Defaults F7 : Optimized Defaults 3.5.2 Internal PCI/IDE Use this item to enable or disable the PCI IDE channels that are integrated on this motherboard. 3.5.3 IDE Primary &...
  • Page 21 Onboard FDC Controller Enabled Item Help Onboard Serial Port 1 3F8 / IRQ4 Menu Level > 　 Onboard Serial Port 2 2F8 / IRQ3 　 UART Mode Select Normal 　 X UR2 Duplex Mode Half Onboard Parallel Port 378 / IR7 Parallel Port Mode X ECP Mode Use DMA Game Port Address...

  • Page 22: Power Management Setup

    This field is used to select the midi port's IRQ. 3.5.21 USB Controller Select Enabled if your system contains a Universal Serial Bus (USB) controller. 3.5.22 USB Keyboard Support This item lets you enable or disable the USB keyboard driver within the onboard BIOS. 3.5.23 IDE HDD Block Mode This feature enhances disk performance by allowing multi-sector data transfers and eliminates the interrupt handling time for each sector.
  • Page 23 S3 (STR): Enables the STR function. 3.6.3 Video Off Option When enabled, this feature allows the VGA adapter to operate in a power saving mode. Always On Monitor will remain on during power saving modes. Suspend --> Off Monitor blanked when the systems enters the Suspend mode.

  • Page 24: Pnp/Pci Configuration Setup

    3.6.11 IRQ [3-7,9-15], NMI When this item is enabled, any activity through the system interrupt request lines 3-7, 9-15 and the non- masked interrupt can reset power-saving mode timeouts to zero, or resume the system from a power-saving mode. 3.6.12 IRQ 8 Break Suspend When this item is enabled, any activity through the system interrupt request lines 8 can reset power-saving mode timeouts to zero, or resume the system from a power-saving mode.

  • Page 25: Pc Health Status

    In case a conflict occurs after you assign the IRQs or after you configure your system, you can enable this function to allow your system to automatically reset your configuration and reassign the IRQs, DMAs, and I/O address. 3.7.2 Resources Controlled By Default setting is "Auto (ESCD)".

  • Page 26: Frequency Control

    The onboard hardware monitor is able to detect the voltage output by the voltage regulators. These values refresh upon any key entry. The function is optional. 3.8.2 Current CPU & System Temperature (xx°C) The onboard hardware monitor is able to detect the temperatures of motherboard and CPU. These values refresh upon any key entry.
  • Page 27 [ If your Windows 95 is older version, please install the USB supplement service pack ( usbsupp.exe ) files first. You can get this file from http://www.microsoft.com 2. Insert the CD Driver into the CD drive-enter the \S630MA\SOUND directory on the CD-ROM and double-click SETUP.EXE 3. Follow the prompts to complete the installation.
  • Page 28 Please refer to the README.TXT file in each directory. 4.3 Installing the Graphics Driver 4.3.1 For Windows 95/98 1. Insert the CD Driver into CD drive - enter the \S630MA\VGA\WIN9X directory on the CD Driver and double- click SETUP.EXE. 2. Follow the prompts to complete the installation.
  • Page 29 8. Place the CD Driver Disk into CD-ROM Drive. 9. When the "Install from Disk" dialog box appears, type the directory storing the drivers and click "OK". The directory in CD-Title is at "D:\S630MA\VGA\WINNT40". 10. When the "Change Display" dialog box appears, click "OK".

Table of Contents