Panasonic CS-A18CKPG Service Manual page 50

NAME OF EACH PART
I Remote Control
1
2
AUTO AUT HEA HEAT COOL COOL DRY DR
AUT AUTO
AUTO AUT
ON
AUT AUTO
OFF
FAN AN
TEMP
3
OFF/ON
POWERFUL
4
5
MODE ECONOMY SLEEP
6
AIR SWING
FAN SPEED
7
1 2 3
8
ON SET
9
OFF
CANCEL
TIMER
0
CHECK RESET CLOCK
G Remote Control Signal.
• Make sure it is not obstructed.
• Maximum distance : 10 m (32.8 ft.).
• Signal received sound.
One short beep or one long beep.
G Notes for Remote Control.
• Do not throw or drop.
• Do not get it wet.
• Certain type of fluorescent lamps may affect
signal reception. Consult your dealer.
PREPARATION BEFORE OPERATION
I Indoor Unit
1
5
2
4 3
1
Open the front panel
2
AUTO HEAT COOL DRY FAN
Remove the air filters
AUTO
3
Fit the air purifying filters in place
4
AUTO
Insert the air filters
FAN
5
Close the front panel
I Remote Control
– To set the current time
AIR SWING
FAN SPEED
1 2 3
ON SET
OFF
CANCEL
TIMER
CHECK RESET CLOCK
1
Press 1.
2
Then press 2 to increase or decrease the time.
3
Press 1 again.
Set time at display will light up.
1 Signal Transmitter
2 Operation Display
3 Powerful Mode Operation Button
4 Room Temperature Setting Button
(Illuminating button)
5 Operation Mode Selection Button
6 Economy Mode Operation Button
7 Vertical Airflow Direction Button
!
8 ON-Timer Button
#
9 OFF-Timer Button
$
0 Reset Point
$
(Press with fine-tipped object to clear the memory)
%
! OFF/ON Button
^
(Illuminating button)
&
*
@ Sleep Mode Operation Button
(
# Fan Speed Selection Button
$ Horizontal Airflow Direction Button
% Timer Set Button
^ Timer Cancellation Button
& Time-Setting Button
* Clock Button
( Remote Control Cover
HOW TO OPERATE
2
3
5
I To start the operation
• Press 1.
• POWER indicator (green) on the indoor unit will light
up.
• To stop, press once more.
I Setting Mode
• Press 2 to select:-
AUTO – Automatic Operation
HEAT – Heating Operation
COOL – Cooling Operation
DRY – Soft Dry Operation
2
1
G How to Insert the Batteries
2
1
Slide down the remote control cover completely
to remove it.
2
Insert the batteries
– Be sure the direction is correct
– 12.00 at display - flashing
• Set the current time (CLOCK) immediately to
prevent battery exhaustion.
3
Re-install the remote control cover by inserting it
in the side groves and pushing inward.
G About the batteries
• Can be used for approximately one year.
G Observe the following when replacing the
batteries
• Replace with new batteries of the same type.
• Do not use rechargeable batteries (Ni-Cd).
• Remove the batteries if the unit is not going to be
used for a long period.
I Setting Temperature
• Press 3 to increase or decrease the temperature.
• The temperature can be set between 60°F ~ 86°F.
• Recommended temperature:
COOL
DRY
1
HEAT
6
4
• During AUTO Operation, press 3 to select:-
• Operation with 4°F higher than the standard
temperature.
• Operation with the standard temperature.
• Operation with 4°F lower than the standard
temperature.
G Standard Temperature
Indoor
temperature
73°F
68°F
• At the beginning of the automatic operation, Heating,
Cooling or Soft Dry is automatically selected according
to the indoor temperature.
• The operation mode changes every hour, when
necessary.
1
75°F ~ 78°F
2°F ~ 4°F
Lower than the
room temperature
68°F ~ 75°F
Standard
Operation temperature
Cooling
77°F
Soft Dry 72°F
Heating 70°F