About The Units And Options; Overview: About The Units And Options; Identification; Identification Label: Outdoor Unit - Daikin ERGA08DAV3 Installer's Reference Manual

4

About the units and options

4.1 Overview: About the units and
options
This chapter contains information about:
▪ Identifying the outdoor unit
▪ Identifying the indoor unit
▪ Combining the outdoor unit with options
▪ Combining the indoor unit with options
4.2

Identification

NOTICE
When installing or servicing several units at the same time,
make sure NOT to switch the service panels between
different models.
4.2.1

Identification label: Outdoor unit

Location
Model identification
Example: ER G A 06 DA V3 A
Code
ER European split outdoor pair heat pump
G Medium water temperature – ambient zone: −10~
−20°C
A Refrigerant R32
06 Capacity class
DA Model series
V3 Power supply
A A=Austrian model
[—]=Non-Austrian model
4.2.2

Identification label: Indoor unit

Location
Model identification
Example: E HV Z 04 S 18 DA 6V G
Code
E European model
HV Floor-standing indoor unit with integrated tank
Z Dual-zone model
04 Capacity class
S Integrated tank material: Stainless steel
ERGA04~08DAV3(A) + EHVZ04+08S18+23DA +
EHVZ04+08S18+23DJ
Daikin Altherma 3 R F
4P495249-1B – 2019.06
Explanation
Description
4 About the units and options
Code
18 Integrated tank volume
DA Model series
6V Backup heater model
G G=Grey model
[—]=White model
4.3

Combining units and options

4.3.1

Possible options for the outdoor unit

Drain pan kit (EKDP008D)
The drain pan kit is required to gather the drain from the outdoor
unit. The drain pan kit consists of:
▪ Drain pan
▪ Installation brackets
For installation instructions, see the installation manual of the drain
pan.
Drain pan heater (EKDPH008CA)
The drain pan heater is required to avoid freezing-up of the drain
pan.
It is recommended to install this option in colder regions with
possible low ambient temperatures or heavy snowfall.
For installation instructions, see the installation manual of the drain
pan heater.
U-beams (EKFT008D)
The U-beams are installation brackets on which the outdoor unit can
be installed.
It is recommended to install this option in colder regions with
possible low ambient temperatures or heavy snowfall.
For installation instructions, see the installation manual of the
outdoor unit.
Low sound cover (EKLN08A1)
In sound sensitive areas (e.g. near a bedroom), you can install the
low sound cover to decrease the operation noise of the outdoor unit.
You can install the low sound cover:
▪ On mounting feet to the ground. This must withstand 200 kg.
▪ On brackets to the wall. This must withstand 200 kg.
If you install the low sound cover, you also need to install one of the
following options:
▪ Recommended: Drain pan kit (with or without drain pan heater)
▪ U-beams
For installation instructions, see the installation manual of the low
sound cover.
4.3.2

Possible options for the indoor unit

User interface used as room thermostat (BRC1HHDA)
▪ The user interface used as room thermostat can only be used in
combination with the user interface connected to the indoor unit.
▪ The user interface used as room thermostat needs to be installed
in the room that you want to control.
For installation instructions, see the installation and operation
manual of the user interface used as room thermostat.
Room thermostat (EKRTWA, EKRTR1)
You can connect an optional room thermostat to the indoor unit. This
thermostat can either be wired (EKRTWA) or wireless (EKRTR1).
Description
Installer reference guide
9