Smeg UG411DSUK Manual

Table of Contents

Quick Links

Download this manual

SUMMARY

PRODUCT IDENTIFICATION .................................................................................................................................. 3

1.1

APPLICATION, GENERAL FUNCTIONS AND INTENDED USE ............................................................................. 3

1.2

NAME AND ADDRESS OF MANUFACTURER OR DISTRIBUTOR......................................................................... 3

SMEG S.P.A. ............................................................................................................................................................. 3

1.3

DECLARATION OF CONFORMITY TO PRODUCT STANDARDS ........................................................................... 3

1.4

DESCRIPTION OF THE APPLIANCE .................................................................................................................. 4

SYMBOLS USED IN THE MANUAL ......................................................................................................................... 4

SAFETY PRECAUTIONS AND INSTRUCTIONS ......................................................................................................... 5

3.1

CORRECT INSTALLATION ............................................................................................................................... 5

3.2

SAFE USE ...................................................................................................................................................... 6

3.3

CORRECT MAINTENANCE .............................................................................................................................. 6

PRODUCT CHARACTERISTICS ................................................................................................................................ 7

4.1

OVERALL DIMENSIONS FOR BUILT-UNDER INSTALLATION ............................................................................. 7

4.2

TECHNICAL CHARACTERISTICS ....................................................................................................................... 8

PREPARING THE APPLIANCE FOR USE .................................................................................................................. 9

5.1

POSITIONING AND INSTALLATION ................................................................................................................. 9

5.2

CONNECTION TO THE WATER SUPPLY ......................................................................................................... 10

5.3

DRAIN CONNECTION ................................................................................................................................... 10

5.4

CONNECTION TO THE ELECTRICITY SUPPLY.................................................................................................. 11

FIRST START-UP ................................................................................................................................................. 12

6.1

FIRST START-UP .......................................................................................................................................... 12

6.2

PREPARING FOR USE ( IMPORTANT ) .......................................................................................................... 12

6.3

USING THE WATER SOFTENER (ON MODELS WITH THIS FEATURE ONLY) ..................................................... 12

CONTROL PANEL ................................................................................................................................................ 13

LIGHT L2 ................................................................................................................................................................ 13

GREEN LIGHT: DISHWASHER READY........................................................................................................................ 13

BLUE LIGHT: DISHWASHER IN OPERATION (WASHING IN PROGRESS, FILL IN PROGRESS ....) .................................... 13

RED LIGHT: INDICATES A MALFUNCTION ................................................................................................................ 13

7.1

SET-UP (AUTHORISED STAFF ONLY) ............................................................................................................ 14

7.2

MODIFIABLE PARAMETERS ......................................................................................................................... 15

7.3

STARTING THE PERISTALTIC PUMPS - RAPID FILLING OF DETERGENT AND RINSE AID DELIVERY CIRCUIT. ..... 18

MALFUNCTIONS SHOWN ON THE DISPLAY (FOR THE TECHNICIAN) ................................................................... 19

INSTRUCTIONS FOR THE USER ........................................................................................................................... 21

LIGHT L2 ................................................................................................................................................................ 21

GREEN LIGHT: DISHWASHER READY........................................................................................................................ 21

BLUE LIGHT: DISHWASHER IN OPERATION (WASHING IN PROGRESS, FILL IN PROGRESS ....) .................................... 21

RED LIGHT: INDICATES A MALFUNCTION ................................................................................................................ 21

9.1

BEFORE WASHING ...................................................................................................................................... 22

9.2

FIRST USE EACH DAY (TANK AND BOILER EMPTY) ........................................................................................ 23

9.3

OPERATING ANOMALIES ............................................................................................................................. 24

9.4

PROGRAM CHANGE .................................................................................................................................... 24

CHOSING THE PROGRAM ............................................................................................................................... 25

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

Table of Contents

Summary of Contents for Smeg UG411DSUK

Page 1: Table Of Contents
PRODUCT IDENTIFICATION ..........................3 APPLICATION, GENERAL FUNCTIONS AND INTENDED USE ................3 NAME AND ADDRESS OF MANUFACTURER OR DISTRIBUTOR................. 3 SMEG S.P.A................................3 DECLARATION OF CONFORMITY TO PRODUCT STANDARDS ................3 DESCRIPTION OF THE APPLIANCE ........................4 SYMBOLS USED IN THE MANUAL ......................... 4 SAFETY PRECAUTIONS AND INSTRUCTIONS ......................
Page 2 MALFUNCTIONS SHOWN ON THE DISPLAY (FOR THE USER) ................32 SMEG thanks you for choosing one of its products. This manual is an integral part of the appliance. Take good care of it and keep it to hand throughout the appliance’s life cycle, since it contains important information about assembly, safety, use and maintenance.
Page 3: Product Identification
Electronic Equipment (WEEE). For information on the treatment, recovery and recycling of this product, contact the local authority, domestic waste collection service, or your Smeg reseller. Make sure that this product is scrapped correctly to safeguard the environment and health.
Page 4: Description Of The Appliance
1.4 Description of the appliance COVER (TOP) DISPLAY AND CONTROL PANEL FRONT LOADING/UNLOADING DOOR SERVICE COMPARTMENT ADJUSTABLE FEET 2 SYMBOLS USED IN THE MANUAL This symbol instructs the user to read the instructions in the manual with care. This symbol appears next to information important for the safety of people and the appliance.
Page 5: Safety Precautions And Instructions
3 SAFETY PRECAUTIONS AND INSTRUCTIONS The precautions and instructions below contain important information and must be read with care. The manufacturer does not accept responsibility for damage caused by failure to comply with the safety precautions and instructions. 3.1 Correct installation ...
Page 6: Safe Use
3.2 Safe use  The staff assigned to use the dishwasher must be suitably trained and instructed.  The appliance is not suitable for use by juveniles or persons with reduced physical, sensorial or mental capacities, or those without the necessary knowledge and experience. Such persons may only use the appliance under the supervision of a person responsible for their safety.
Page 7: Product Characteristics
4 PRODUCT CHARACTERISTICS 4.1 Overall dimensions for built-under installation LOWER BACK PANEL ELECTRICITY SUPPLY CABLE FILLER HOSE PERISTALTIC HOSES EARTH TERMINAL DRAIN HOSE EXTERNAL DISPENSER POWER CABLE ENTRY POINT...
Page 8: Technical Characteristics
4.2 Technical characteristics Electricity supply See technical data plate and Intake water pressure electrical wiring diagram supplied with the appliance Intake water temperature Indoor Max. working altitude 2000 Working ambient temperature °C 10 - 35 Relative humidity 80% for temperatures up to 25°C with linear decrease to 50% at the temperature of 35°C...
Page 9: Preparing The Appliance For Use
5 PREPARING THE APPLIANCE FOR USE Convey the dishwasher to the installation site, remove the packaging and check the appliance and components for damage; any damage found must be reported to the transporter in writing. The packaging components (plastic bags, expanded polystyrene, nails, etc.) must not be left within reach of children and pets since they are potentially dangerous.
Page 10: Connection To The Water Supply
5.2 Connection to the water supply Check that the intake water pressure, flow rate and temperature are as stated in the dishwasher's technical characteristics. If the dynamic pressure exceeds the limit stated in technical characteristics, a pressure reducer must be installed. If the pressure lower, it might be necessary to fit a special pump to ensure optimal performance.
Page 11: Connection To The Electricity Supply
5.4 Connection to the electricity supply The dishwasher must be connected to the electrical system by authorised, skilled staff, in accordance with the relevant regulations. Also comply with the technical instructions for the connection provided with the appliance. The dishwasher's rated electrical characteristics are provided on its technical data plate. A circuit breaker with contact gap rated for category II overvoltage and an overcurrent protection device (magnetothermal switch or fuses) must be installed in an easily accessible position on the dishwasher's power supply line.
Page 12: First Start-Up
6 FIRST START-UP 6.1 First start-up The electrical protection system must undergo a functional test before the appliance is put into operation. The appliance must be installed and/or inspected by qualified staff, who will start it up for the first time and provide the relevant operating instructions.
Page 13: Control Panel
7 CONTROL PANEL On-off button Program selection button Start CONFIRM/PAUSE button Total emptying button (tank and boiler) Additional function selection button L1 Mains power on light L2 Light indicating dishwasher in operation, cycle running, FILL running…. (blue), ready (green), malfunction (red) L3 Pump-out in progress light No rinse-aid symbol (if a system for monitoring outside the dishwasher is provided) Tank heating element on symbol...
Page 14: Set-Up (Authorised Staff Only)
When the display control panel is switched on, the display shows the type of dishwasher (PRF 400, PRF 500, CAPOTE…….), followed by the firmware version and update installed. If the dishwasher is already powered up, press the on/off button for direct display of the firmware version and update installed.
Page 15: Modifiable Parameters
7.2 Modifiable parameters The illustrations are purely guideline. The minimum and maximum temperatures available depend on the model (glass washer, dishwasher, undercounter or hood-type model, ..). Rinsing temperature Washing temperature (boiler temperature) (tank temperature) Warning: The tank and boiler temperatures shown on the display may be different from the actual temperatures by a few degrees, especially in transient phases (just after the FILL is completed, just after the end of the cycle, etc.) due to the inertia of the measurement probe.
Page 16 Autostart function Set at “on” to start the cycle when the hood/door is closed. Set at “off” to start the cycle after confirmation with the start button Regeneration frequency setup (models with softener) * (Default value: H03; modify the parameter to suit the mains water hardness. At first use, the salt tank has to be filled.
Page 17 "Clean water" cycle When this option is activated, the appliance pumps out all the water from the tank and then refills it with clean water at every wash cycle. How long this operation takes depends on the washing water temperature. On: enabled –...
Page 18: Starting The Peristaltic Pumps - Rapid Filling Of Detergent And Rinse Aid Delivery Circuit
USER program duration customisation (optional, only if installed) USER. is the only program which can be customised. Scroll through the setup parameters to display USER.P1, P2….. followed by two dashes (e.g. P2--). Keep pressing the P button until USER appears followed by the duration (e.g.
Page 19: Malfunctions Shown On The Display (For The Technician)
8 MALFUNCTIONS SHOWN ON THE DISPLAY (FOR THE TECHNICIAN) The dishwasher is able to identify a number of malfunctions and show them on the display. If the problem persists after the dishwasher has been switched off and back on, proceed as described below: Tank temperature probe Tank temperature probe disconnected or not working.
Page 20 Boiler water filling The boiler wasn’t filled in the expected time: check the water malfunction supply tap, the dynamic supply pressure, cleanliness of the inlet water filter, any damage of the water charging hose, or check the Er 25 following in this order: - faulty boiler pressure switch (it always detects “empty”), - leakage or unbinding of the tube (water runs inside the tube) - menu service wrong setting “rP”...
Page 21: Instructions For The User
9 INSTRUCTIONS FOR THE USER Control panel On-off button Program selection button Start CONFIRM/PAUSE button Total emptying button (tank and boiler) Additional function selection button L1 Mains power on light L2 Light indicating dishwasher in operation, cycle running, FILL running…. (blue), ready (green), malfunction (red) L3 Pump-out in progress light No rinse-aid symbol (if a system for monitoring outside the dishwasher is provided)
Page 22: Before Washing
Use only detergents and rinse aids for industrial dishwashers. Do not use detergents intended for hand washing. We recommend the use of Smeg products, specially developed for this dishwasher. When topping up the tanks, take care not to swap the products; this might damage the dishwasher and cause malfunctions.
Page 23: First Use Each Day (Tank And Boiler Empty)
9.2 First use each day (tank and boiler empty) With the door/hood closed: Press and hold it down. The display shows the firmware version and update installed, then the tank and boiler temperatures. This is followed by FILL and the boiler water temperature. The boiler heating element symbol remains lit until heating finishes.
Page 24: Operating Anomalies
9.3 Operating anomalies Open door. If the door is opened with the cycle in progress, “CLOSE” flashes and the program stops. After closing the door, the program start must be confirmed by pressing holding it down for 1 second (light L2 changes from green to blue).
Page 25: Chosing The Program
10 CHOSING THE PROGRAM Scrolling through the programs available displays first the program name (in English) and hen the number (P1, P2….. etc.) followed by the duration. PROGRAM TYPE OF DIRT DURATION (*) GLASS Short P1 Dirty soiled glasses 1 min Glass Medium P2 Normally soiled glasses 1 min 20s...
Page 26: Baskets Provided
11 BASKETS PROVIDED The shape and material of the baskets provided with the dishwasher depend on the purchased model. Extra baskets can be purchased through the After-Sale Service. The following images are indicative. Glasses: Place the glasses downwards. Cutlery Use the dedicated basket. Place the cutlery randomly, preferably with the handle downwards,...
Page 27: Maintenance An Cleaning
12 MAINTENANCE AN CLEANING We recommend regular servicing by a SMEG authorised service centre at least once a year, to guarantee optimal performance at all times. Consumables (e.g. peristaltic pump hoses) and/or parts subject to wear and tear must be replaced with genuine SMEG parts.
Page 28: Cleaning The Filter During The Day
12.1 Cleaning the filter during the day In case of particularly heavy-duty working conditions, the filter should be cleaned every 30-40 cycles, keeping the machine in operating conditions; to do this, carry out the “partial tank pump-out” routine (program “P0”)) (TANK UNL). Press the button, and hold it down, until “TANK UNL”...
Page 29: Topping Up With Regenerating Salt (For Models With Softener)
12.3 Topping up with regenerating salt (for models with softener) Warning: use specific salt only, do not use cooking sea salt. Salt must be supplied when the led under the symbol indicated in the left side picture lights up. The salt container has a capacity of about 1 kg of granulated salt. Correct procedure to refill the regenerating salt: - start a tank pump-out, - refill the regenerating salt,...
Page 30 THE INDICATOR LIGHT L1 DOES line voltage failure Verify electricity connection. NOT LIGHT UP The dishwasher filling is not over Wait for FILL to disappear off the yet. display THE WASHING PROGRAM DOES NOT START If CLOSE stays even with the hood CLOSE stays on display closed, contact the After-Sales Service.
Page 31 Verify that the tube and drainage are WATER LEFT IN THE TANK AFTER Waste tube badly positioned or not clogged and that the drainage is PUMP-OUT. partially clogged. not positioned too high; see connection scheme.
Page 32: Malfunctions Shown On The Display (For The User)
14 MALFUNCTIONS SHOWN ON THE DISPLAY (FOR THE USER) The dishwasher can show a series of malfunctions on display. After the machine has been switched off and restarted, if the problem is not solved, follow the steps below: ( FOR A MORE PROFICIENT AFTER-SALES SERVICE, ALWAYS TAKE NOTE OF THE INDICATED ERROR ) Err04 Tank temperature probe anomaly Contact After-sales Service...

Smeg UG411DSUK Manual

Quick Links

Related Manuals for Smeg UG411DSUK

Summary of Contents for Smeg UG411DSUK

Table of Contents