Kawai ANYTIME X2 GP Service Manual page 45

〔6〕 PARTS LIST & ASSEMBLING INSTRUCTIONS
【 I 】 Drive Lever
【I-2】 Drive Lever (P)
Assembling Instruction
【Refer to Drawing in Left】
1. Fasten muffler arm support ②
on drive lever base ① with two screws ⑪ .
2. Press fit two bushes ④ to drive lever (P) ③ .
3. Insert the bush part of drive lever (P) ③ into drive lever base ① .
4. Apply the bond (G-17) on the shaft of drive lever base ① , then insert muffler arm stopper rubber ⑥ on it.
5. Hook up muffler spring ⑬ on drive lever base ① and drive lever (P) ③ .
【Refer to Drawing in Right】
6. Attach lever base spacer ⑭ behind the action crosspiece inside the rim block of piano with double-
sided adhesive tape ⑯ .
＊ Fill up the hollow for installing the action crosspiece with spacer wood ⑮ .
7. Attach the assembled drive lever base ① on the piano with two screws ⑱ .
＊ The screws ⑱ should touch the rim of the block.
8. Pass control wire assy ⑩ through wire fittings ⑦ , then insert muffler arm bush ⑧ in it.
9. Pass the outer part of control wire assy ⑩ through muffler wire support ② , then insert wire fittings
⑦ into drive lever base ① .
10. Apply grease on the shaft of drive lever (P) ③ , then insert one polyslider washer and roller on it in
the order shown in the drawing.
11. Fasten wire set fittings ⑨ on drive lever (P) ③ with two screws ⑪ .
【Refer to drawing below】
12. Check if the centers of roller and adjust lever are well aligned by observing from top of piano.
＊ If there is more than 3 mm gap, exchange, add or remove Lever base spacers ⑭ as needed.
All manuals and user guides at all-guides.com
Apply adhesive around
the rod base (G-17)
3
6
4
4 11
2
11
13
1
Apply a slight coat of
grease on the rod
17
5
9
12
16
7
No. Description
1 Drive Lever Base
2 Muffler Wire Support
3 Drive Lever (P)
4 Bush
5 Roller
6 Muffler Arm Stopper Rubber
7 Wire Ftgs.
8 Muffler Arm Bush
9 Wire Set Ftgs.
10 Control Wire Assy
11 + FLAT MACHINE SCREW
12 + BINDING MACHINE SCREW + Binding machine screw
13 Muffler Spring
14 Lever Base Spacer
15 Spacer Wood
Lever Base Both Side
16
Adhesive Tape
17 Polyslider Washer
+ TRUSS TAPPING SCREW
18
TYPE A
– 45 –
8
10
Description Remarks
Drive lever base
Muffler wire support
Drive lever (P)
Bush
Roller
Muffler arm stopper rubber
Wire fittings
Muffler arm bush
Wire set fittings
Control wire assy
+ Flat machine screw M3x10
M3x6 Black
Muffler Spring
GM, GE, RX-1 t=6
Lever base spacer RX-2, 3 t=9
RX-5 t=3
Spacer wood
Lever base Double-sided
adhesive tape
Polyslider washer t=0.5 4.2- 10
+ Truss tapping screw type A 6 x 20
16
15
16
14
PN
916510
471798
916528
53449
916820
562653
916838
463400
916854
916978
917249
878804
985252
926396
926370
926418
-
-
914851
878961