Table of Contents
Advertisement
T
E
M
P
To access temperature control through the VPM5580TC
(either locally or remotely), use the Automation menu
as described in the Instruction Manual.
(01) Event Initiated (Follows PGM Output Only):
The occupancy setting will follow the state of its
assigned PGM output. See Assigning Occupancy
Settings to PGM Outputs in section 9.8.
Example : If the Day occupancy setting is assigned
to a PGM programmed to follow arming status, the
VPM5580TC will switch the thermostat to the Day
setting whenever the system is armed.
(02) Follows Schedule Only: The item will follow
its assigned schedules. See Assigning Schedules
for Temperature Control (section 9.6).
Example : If the Night occupancy setting is assigned
to schedule 3, which activates at 19:00, the VPM5580TC
will switch the thermostat to the Night setting at 7:00pm
every day. The thermostat will remain switched to the
Night setting until a user, another schedule or an event
switches it to another setting.
(03) Follows Schedule or Event Initiation (PGM
Output): The occupancy setting activates when its
assigned schedules are active. The occupancy
setting will also activate when its assigned PGM
output is active. If the schedules and the output are
active at the same time, the occupancy setting will
also be active. See Assigning Schedules for
Temperature Control and Assigning Occupancy
Settings to PGM Outputs (sections 9.6 and 9.8).
Example : The Night occupancy setting is assigned
to schedule 3, which activates at 19:00 and
deactivates at 06:00 the next day and a PGM
output programmed to follow arming status.
The VPM5580TC will switch the thermostat to the
Night setting at 7:00pm every day. Also, whenever
the system is armed, the VPM5580TC will switch
the thermostat to the Night setting.
(04) Follows Schedule and Event Initiation (PGM
Output): The occupancy setting activates only
when its assigned schedules are active at the
same time as the assigned PGM output is active.
E
R
A
T
U
firealarmresources.com
R
E
C
O
See Assigning Schedules for Temperature Control
and Assigning Occupancy Settings to PGM Outputs
(sections 9.6 and 9.8).
Example : The Day occupancy setting is assigned
to schedule 4, which activates at 09:00 and
deactivates at 22:00 every day and a PGM
programmed to follow arming status.
If the system is armed between 9:00am and
10:00pm, the VPM5580TC will switch the thermostat
to the Day occupancy setting. If the system is
disarmed between 9:00am and 10:00pm, the
VPM5580TC will not switch the thermostat to the
Day occupancy setting. The thermostat will continue
to use whatever setting it was in previously.
9.5 Selecting Thermostat Options
Turn options 01-08 in sections [800], [821],
[842], [863] ON or OFF to define how each
thermostat item will work. Sections [800], [821],
[842], [863] are the options for thermostats 1, 2,
3 and 4 respectively.
Option [01]: Thermostat Enrolled
Turn this option ON for each thermostat that is
connected.
Option [02]: Exterior Temperature Sensor
Turn this option ON if there is an EMS-OTS
connected to the thermostat.
Option [03]: Heat Enabled
Turn this option ON if the thermostat is connected
to, and controlling, a heating device.
Option [04]: Cool Enabled
Turn this option ON if the thermostat is connected
to, and controlling, a cooling device.
Option [05]: Day Setting Mode Option
Follows Schedule / Output Condition Always.
The Day Occupancy Setting will always follow the
Schedule / Output condition programmed in the
24
N
T
R
O
L
Advertisement
Table of Contents
