Table of Contents
Advertisement
The following sections describe how to program the
VPM5580TC. All VPM5580TC programming can be
done via any local touchtone telephone or via the
DLS software through the security control panel.
It is extremely important that you read
this section of the manual completely
before attempting to program the
VPM5580TC module.
When using the VPM5580TC module,
do not turn on the Daylight Savings
Time option in the control panel
programming (if this option is present
in the panel). This option will be
controlled by the Communiqué system.
3.1 Entering Installer Programming
With the system disarmed:
1. From a Communiqué telephone, press the
[SECURITY] key. If you are using a telephone
connected to a Communiqué DAI station, press
[7][3] (Security Functions). The system will
"Hello"
"Hello"
announce "Hello"
"Hello"
"Hello" . . . . .
2. Enter programming mode by pressing
[ ][8]. The system prompts:
"Enter the Service Code"
"Enter the Service Code"
"Enter the Service Code"
"Enter the Service Code"
"Enter the Service Code"
3. Enter the 4-digit Service code. The default service
code is [5580]. (You can change the service
code in programming section [001].) After the
service code is entered, the system prompts:
"Enter a Section Number. T
"Enter a Section Number. T
"Enter a Section Number. To exit, press
"Enter a Section Number. T
"Enter a Section Number. T
[#]"
[#]"
[#]"
[#]"
[#]"
4. To enter a programming section, enter the 3-digit
number of the section. If you make an error
entering the section number, the system prompts:
"Inv
"Inv
alid entry
alid entry
. Enter a Section Number.
. Enter a Section Number.
"Inv
"Inv
"Invalid entry
alid entry. Enter a Section Number.
alid entry
. Enter a Section Number.
. Enter a Section Number.
T T T T T o exit, press [#]"
o exit, press [#]"
o exit, press [#]"
o exit, press [#]"
o exit, press [#]"
When you enter a section number, the system
announces the section you have entered with
the prompt:
"Section (number)"
"Section (number)"
"Section (number)"
"Section (number)"
"Section (number)"
How to Program
S
E
C
T
o exit, press
o exit, press
o exit, press
o exit, press
8
firealarmresources.com
I
O
N
3
For programming changes to take
effect, you must exit Installer's pro-
gramming and close the connection
with the VPM5580TC.
3.2 Programming Data Entry
Sections
To program a data entry section from the
VPM5580TC programming mode:
1. Enter the 3-digit section number.
2. The system announces the section you have
entered with the prompt:
"Section (number)"
"Section (number)"
"Section (number)"
"Section (number)"
"Section (number)"
The system announces the data presently
programmed in the programming section as:
"Data is (data)"
"Data is (data)"
"Data is (data)"
"Data is (data)"
"Data is (data)"
The system then prompts:
"Enter new data"
"Enter ne
"Enter ne
"Enter ne
"Enter ne
3. Enter the new data in the section, or return to
the "Enter a Section Number" prompt, by
pressing [#].
When you have finished entering the new data,
the system announces the new data with the
prompt:
"Data is (data)"
"Data is (data)"
"Data is (data)"
"Data is (data)"
"Data is (data)"
If you make an invalid data entry, the system
announces:
"Inv
"Inv
"Invalid Entry
"Inv
"Inv
alid Entry
alid Entry. Data is (data). Enter
alid Entry
alid Entry
. Data is (data). Enter
. Data is (data). Enter
. Data is (data). Enter
. Data is (data). Enter
ne
ne
ne
ne
new data. T
w data. T
w data. T
w data. T
w data. To exit, press pound."
o exit, press pound."
o exit, press pound."
o exit, press pound."
o exit, press pound."
4. Record the new data in the appropriate section
of the Programming Worksheets.
w data"
w data"
w data"
w data"
Advertisement
Table of Contents
