Table of Contents
Advertisement
P
R
O
3.3 Programming Toggle Option
Sections
To program a section with toggle options from the
VPM5580TC programming mode:
1. Enter the 3-digit section number.
2. The system announces the section you have
entered with the prompt:
"Section (number)"
"Section (number)"
"Section (number)"
"Section (number)"
"Section (number)"
The system announces which options are
presently turned ON with one of the following
prompts:
"All options are of
"All options are of
"All options are off" f" f" f" f"
"All options are of
"All options are of
"All options are on"
"All options are on"
"All options are on"
"All options are on"
"All options are on"
"Option (number) is on"
"Option (number) is on"
"Option (number) is on"
"Option (number) is on"
"Option (number) is on"
"Options (numbers) are on"
"Options (numbers) are on"
"Options (numbers) are on"
"Options (numbers) are on"
"Options (numbers) are on"
The system then prompts:
"Enter tw
"Enter tw
"Enter two digit option. T
"Enter tw
"Enter tw
o digit option. T
o digit option. T
o digit option. To Exit, press
o digit option. T
pound"
pound"
pound"
pound"
pound"
3. To exit the section without making any changes,
press [#].
To turn an option ON or OFF, enter the 2-digit
option number.
If you enter an invalid option number, the
system prompts:
"Inv
"Inv
"Invalid entry"
"Inv
"Inv
alid entry"
alid entry"
alid entry"
alid entry"
After you enter a valid option number, the
system again announces which options are
ON.
4. When you have finished programming the
options in the section, press [#]. The system
returns to the "Enter a Section Number" prompt.
5. Record your new programming choices in the
appropriate section of the Programming
Worksheets.
G
R
A
3.4 Programming Label Entry
To program or change a label:
1. Enter the section number of the label. The
2. Enter the first word of the label using the 3-digit
o Exit, press
o Exit, press
o Exit, press
o Exit, press
"Invalid entry
"Inv
"Inv
"Inv
"Inv
3. If you have more words to program, enter the
4. When you have entered six words, the system
5. To have the system read the new label to you,
6. If the label is correct, press [#]. To change the
7. Record the new label in the appropriate section
Adding Numbers to Labels
Three special Number Commands are available to
allow the system to include a number in the voice
label. The number commands allow the system to
announce the number in three different modes:
Label 000: Number Command 1, Combined
Form. The number will be announced in its full
form. For example, the number 401 would be
announced as "four hundred and one" .
9
firealarmresources.com
M
M
Sections
system announces the section number and
then recites the words presently programmed
in the label. Each label may have up to six
words. The system then prompts:
"Enter three digit w
"Enter three digit word. T
"Enter three digit w
"Enter three digit w
"Enter three digit w
pound".
pound".
pound".
pound".
pound".
codes from the Label Library in Appendix B of
the Programming Worksheets.
The system beeps at the end of each correctly
entered code and the system prompts:
"Enter three digit w
"Enter three digit w
"Enter three digit word. T
"Enter three digit w
"Enter three digit w
pound"
pound"
pound"
pound"
pound"
If you make an invalid entry, the system
prompts:
alid entry
alid entry
alid entry
alid entry. Enter three digit w
. Enter three digit w
. Enter three digit w
. Enter three digit word. T
. Enter three digit w
exit press pound"
exit press pound"
exit press pound"
exit press pound"
exit press pound"
3-digit code of each word until you are finished.
will recite the label. If your label is less than six
words, press [#].
enter the programming section for the label
again.
label again, repeat steps 1-5, above.
of the Programming Worksheets.
I
N
G
ord. To exit, press
ord. T
ord. T
o exit, press
o exit, press
o exit, press
ord. T
o exit, press
ord. T
ord. T
o exit press
o exit press
ord. To exit press
ord. T
o exit press
o exit press
ord. To o o o o
ord. T
ord. T
ord. T
Advertisement
Table of Contents
