Table of Contents
Advertisement
Communicating with the ICU Controller
Notes
• The time required for establishing communication depends on the
communication conditions. If the MAIN MENU does not appear after 1
minute has elapsed, turn off the POWER switch and turn it on again.
• If the phone number has not been registered, the cellular phone is not
connected correctly or the power of the cellular phone is not turned on,
the unit cannot start dialing and the title display remains.
When the unit is used as wired controller
Set the POWER switch on the unit to ON.
The title display appears in the display window.
J U M B O T R O N
M A I N T E N A N C E E Q U I P M E N T
J M E - S A 2 0 0
When communication is established, the MAIN MENU appears in the
display window.
* * * * * * M A I N M E N U * * * * * *
S W I T C H E R C O N T R O L
S I G N A L C O N T R O L
G E O M E T R Y C O N T R O L
M O N I T O R C O N T R O L
S C R E E N C O N T R O L
S C R E E N U N I T C O N T R O L
O T H E R C O N T R O L
Note
The time required for establishing communication depends on the
communication conditions. If the MAIN MENU does not appear after 1
minute has elapsed, turn off the POWER switch and turn it on again.
22
Before Adjustment
Adjustment
Setting the Information about the Screen
Before using the unit, set the information about your JumboTron system,
such as the number of display units constituting the screen. If the correct
information is not set, the adjustments cannot be performed correctly.
1
Establish communication with the ICU controller (page 21) and
display the MAIN MENU.
2
Press the v or V button to select SCREEN CONTROL and press the
ENTER button.
The SCREEN CONTROL menu appears.
* * * * * * M A I N M E N U * * * * * *
S W I T C H E R C O N T R O L
S I G N A L C O N T R O L
G E O M E T R Y C O N T R O L
M O N I T O R C O N T R O L
S C R E E N C O N T R O L
S C R E E N U N I T C O N T R O L
O T H E R C O N T R O L
3
Set the number of display units constituting the screen.
Press the v or V button to select X, Y or Z and press the B or b button
to change the number.
By pressing the v button, X, Y and Z are selected in order. By
pressing the V button, they are selected in the reverse order.
* * * S C R E E N C O N T R O L * * *
U N I T T Y P E : L D U - 1 5
N U M B E R O F U N I T
X :
1 0
B R I G H T N E S S :
M I X L E V E L
R E D M A X : 4 0 M I N :
G R N M A X : 4 0 M I N :
B L U M A X : 4 0 M I N :
Example: For a screen with 3 units horizontally and 4 units
vertically, set to X: 3, Y: 4.
X
Y
Note
If only one screen is installed, do not change "Z" from 1. If a number
other than 1 is set, the unit cannot perform the adjustments.
4
After setting, press the ENTER button.
The set data are stored in memory.
* * * S C R E E N C O N T R O L * * *
U N I T T Y P E : L D U - 1 5
N U M B E R O F U N I T
X : 4 0
Y : 3 0
Z : 1
B R I G H T N E S S :
1 5
M I X L E V E L
R E D M A X : 4 0 M I N :
0
G R N M A X : 4 0 M I N :
0
B L U M A X : 4 0 M I N :
0
Currently selected display unit type
Y : 3 0
Z : 1
X: Number of units in horizontal direction
1 5
Y: Number of units in vertical direction
Z: Number of screens
0
0
0
(continued)
23
Before Adjustment
Adjustment
Advertisement
Table of Contents
