Appendix J - List Of Parameters; Values) - Riello Array AR 399 SE Installation, Operation And Service Manual

APPENDIX
APPENDIX J - LIST OF PARAMETERS (WITH RANGES AND DEFAULT VALUES)
Parameters are listed base on the reference menu.
Reference Menu
M1 Boiler parameters menu
M2 System cascade settings menu
M3 Boiler cascade settings menu
M4 Appliance configuration menu
Nr. dis-
Par.
Menu played
No.
Display
M1 1 CH mode
CH set-
M1 3
point
Calc.
set-
M1 109
point
off-set
CH Min.
M1 110 Set-
point
CH Min.
M1 111 Set-
point
Boiler
M1 5 Pump
Overrun
CH Hys-
M1 7
teresis
CH Hys-
M1 112 teresis
Down
An-
M1 9 ti-cycle
Period
An-
ti-cycle
M1 10
Temp.
Diff.
Max.
M1 14 Power
CH
Min.
M1 15 Power
CH/DHW
Design
M1 19 Supply
Temp.
Design
M1 20 Outdoor
Temp.
Baseline
M1 21 Supply
Temp.
Baseline
M1 22 Outdoor
Temp.
Description
Defines the boiler's various heating operation
modes.
Defines the desired supply temperature in heating
mode (Par. 1) = 0.
Establishes the set-point offset value calculated in
climatic mode (Par. 1= 1). Offsets the climatic curve
in presence of mild outdoor temperatures.
Sets the minimum supply temperature value in
heating mode (Par. 1) = 4.
Sets the maximum supply temperature value in
heating mode (Par. 1) = 4.
Sets the overrun time in seconds of the boiler's
circulator during stand-alone operation; cascade
operation determines the boiler's overrun after
switch-off due to temperature control.
Sets the value in degrees beyond the set-point at
which the burner switches off for thermoregula-
tion.
Sets the value in degrees below the set-point at
which the burner switches on again for thermoreg-
ulation.
Sets the stand-by time before the appliance is
switched on again after it switches off due to
thermoregulation, independently from the supply
temperature dropping below the value indicated in
Par. 10. Parameter valid only in stand-alone mode.
Sets the value in degrees below which the burner
switches on again notwithstanding from the time
spent at Par. 9.
Sets the heating's % max. power.
Sets the heating's % min. power.
Defines the max. set-point at the minimum out-
door temperature for climatic regulation.
Defines the minimum outdoor temperature to
which the maximum set-point can be associated
for climatic regulation.
Defines the minimum set-point at the maximum
outdoor temperature for climatic regulation.
Defines the maximum minimum outdoor tem-
perature to which the minimum set-point can be
associated for climatic regulation.
Access type
U End user
I Installer
Range
0 - 5
Par. 23 - Par. 24
Off, - 10 - 10
68 - 122
(20 - 50)
122 - 194
(50 - 90)
0 - 900
0 - 36
(0 - 20)
0 - 36
(0 - 20)
10 - 900
0 - 36
(0 - 20)
50 - 100
1 - 30
86 - 194
(30 - 90)
-52 - 52
(-25 - 25)
86 - 194
(30 - 90)
-32 - 86
(0 - 30)
71 71
RECYCLING AND DISPOSAL
Default Access
UM
setting type
0 I
158 (70) °F (°C) U
0 I
86 (30) °F (°C) I
176 (80) °F (°C) I
140 Sec. I
11 (5) °F (°C) I
11 (5) °F (°C) I
120 Sec. I
60.8 (16) °F (°C) I
100 % I
1 % I
176 (80) °F (°C) U
0 (0) °F (°C) U
104 (40) °F (°C) I
68 (20) °F (°C) I
APPENDIX
Category
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating
Heating