Page 3: Table Of Contents
Table of Contents Introduction ... 1 Instrumentation ... 7 Audio ... 21 Controls and Features ... 59 Seating and Safety Restraints ... 97 Starting ... 153 Driving ... 163 Roadside Emergencies ... 199 Maintenance and Care ... 229 Capacities and Specifications ... 293 Reporting Safety Defects (U.S.
Page 4: Introduction
Introduction Ford’s Commitment to You At Ford Motor Company, excellence is the continuous commitment to achieve the best result possible. It is dedication to learning what you want, determination to develop the right concept, and execution of that concept with care, precision, and attention to detail.
Page 5 Integrity is never compromised. Our conduct worldwide must be pursued in a manner that is socially responsible and commands respect for its integrity and for its positive contributions to society. NOTES and WARNINGS NOTES give you additional information about the subject matter you are referencing. WARNINGS remind you to be especially careful in those areas where carelessness can cause damage to your vehicle or personal injury to...
Page 6 Canadian Owners — French Version French Owner Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3. Your Maintenance Schedule and Record Booklet...
Page 7 Ford ESP is an optional service contract, backed and administered by Ford. It provides: protection against repair costs after your Bumper to Bumper Warranty expires; other benefits during the warranty period (such as: reimbursement for rentals; coverage for certain maintenance and wear items).
Page 8 Your Ford dealer has information about the availability of many items of equipment which may be ordered for your vehicle.
Page 9 500 miles/800 km after any wheel change or any other time the wheel lug nuts have been loosened. Use only the type of engine oil that Ford recommends. See Engine oil recommendations in the Index. Do not use special “break-in”...
Page 10: Instrumentation
Instrumentation The instrument panel (dashboard) on your vehicle is divided into several different sections. The illustrations on the following pages show the major parts of the instrument panel that are described in this chapter. Some items shown may not be on all vehicles. In your vehicle, the warning lights and gauges are grouped together on the instrument panel.
Page 12 The Mechanical Cluster The following warning lights and gauges are on the mechanical cluster. All of the warning lights and gauges alert you to possible problems with your vehicle. Some of the lights listed are optional. The following sections detail what each of these indicators means.
Page 13 Rear Anti-Lock (ABS) Brake Warning Light To check the rear ABS brake warning light, turn the ignition key to the ON position. The rear ABS brake warning light should glow momentarily. NOTE: If it does not glow momentarily, have your vehicle’s electrical system checked immediately.
Page 14 Safety Belt Warning Light and Chime This warning light and chime remind you to fasten your safety belt. One of the following will take place: If the safety belt is not buckled when the key is turned to the ON position, the light comes on for 1 to 2 minutes and the chime sounds for 4 to 8 seconds.
Page 15 Check Engine Warning Light This light illuminates when the engine’s Emission Control System requires service. It will also illuminate when the ignition key is in the ON position and the engine is off. Check engine warning light Electronic 4-Wheel Drive Warning Light (If equipped) The Electronic 4-Wheel Drive Warning Light illuminates when the Electronic 4-Wheel Drive...
Page 16 Electronic 4-wheel drive warning light Charging System Light This light indicates that your battery is not being charged and that you need to have the electrical system checked. Charging system light This light illuminates every time you turn the ignition to the ON or START position (engine off).
Page 17 Supplemental air bag readiness light High Beam Light This light illuminates when the headlamps are turned to high beam or when you flash the lights. High beam indicator light Chime for Headlamps On This chime sounds if the driver or passenger door is open when the parking lamps or headlamps are on.
Page 18 Battery Voltage Gauge (Voltmeter) This gauge shows you the battery voltage when the ignition key is in the ON position. If you are running electrical accessories (when the engine is off, or idling at a low speed), the pointer may move toward the lower end of the normal band.
Page 19 Engine Oil Pressure Gauge This gauge indicates the engine’s oil pressure, not the oil level. However, if your engine’s oil level is low, it could affect the oil pressure. With the engine running, the pointer should move into the NORMAL band. If the pointer drops below the NORMAL band while the engine is running, you have lost oil pressure and continued operation will cause severe engine...
Page 20 Fuel Gauge The fuel gauge displays approximately how much fuel is in the fuel tank only when the ignition switch is ON. For a proper fuel gauge indication after adding fuel, the ignition switch should be in the OFF position while the vehicle is being refueled. The fuel gauge indicator may vary slightly while the vehicle is in motion.
Page 21 If your engine overheats: 1. Pull off the road as soon as it is safely possible. 2. Turn off the engine. 3. Let the engine cool. DO NOT REMOVE COOLANT SYSTEM FILL CAP UNTIL THE ENGINE IS COOL. 4. Check the coolant level following the instructions on checking and adding coolant to your engine.
Page 22 NOTE: The conversion constant can only be changed six times once the vehicle leaves the factory. Your Ford dealership service personnel can change the conversion constant. Some vehicles are equipped with a vehicle speed (mph/km/h) limiting device that is contained within the Powertrain Control Module (PCM).
Page 23 Odometer/Trip Odometer The Liquid Crystal Display (LCD) odometer is a combination trip odometer and total odometer. The total odometer is normally displayed. To see the trip odometer, press and release the SELECT control on the upper right side of the speedometer.
Page 25 Compact Disc Radio The Compact Disc Radio combines the Electronic Stereo Radio with the Ford Compact Disc Player. Using the Controls on Your New Radio/CD Player Most of the features of this unit work for both radio and CD operation. Also, some of the knobs...
Page 26 How to tune radio stations There are four ways for you to tune in a particular station. You can manually locate the station using the “SCAN/TUNE” button, “SEEK” the station, “SCAN” to the station or select the station by using the memory buttons, which you can set to any desired frequency.
Page 27 Using the “SEEK” function This feature on your radio allows you to automatically select listenable stations up or down the frequency band. Press the top ( a ) half of the “SEEK” button to select the next listenable station up the frequency band. Press the bottom ( b ) half of the button to select the next listenable station down the frequency band.
Page 28 Setting the Station Memory Preset buttons Your radio is equipped with 5 station memory buttons. These buttons can be used to select up to 5 preset AM stations and 10 FM stations (5 in FM1 and 5 in FM2). Follow the easy steps below to set these buttons to the desired frequencies.
Page 29 Activate Auto Memory Store by pushing the “AUTO PRESET” button once. Your radio will set the first five strong stations of the band you are in (AM, FM1 or FM2) into the memory buttons. The display will show “AUTO,” then run through the frequencies, stopping momentarily on the stations being set into the memory buttons.
Page 30: Audio
Using the “AUDIO” button to adjust the tone balance and speaker output Increasing or decreasing bass response Push the “AUDIO” button repeatedly until the display reads “BASS.” Push the “+” side of the “VOL” button to increase bass (more “lows”), and push the “-” side to decrease bass (less “lows”).
Page 31 NOTE: Illuminated bars in the display show relative levels of bass and treble and positions of speaker balance and fader functions after adjustments are made, then revert to volume level set. Clock operation When in the radio mode, push the “CLOCK” button to switch from radio frequency to clock.
Page 32 Using the Controls on Your New Compact Disc Player Your new Ford Compact Disc Player is capable of playing 12 cm or 8 cm discs, without an adapter. The player operates when the power is on and a disc is inserted (label side up). Handle the disc by its edge only.
Page 33 NOTE: Once a disc is inserted, the disc opening is secured to prevent the accidental insertion of a second disc. NOTE: The CD player has heat protection circuitry to protect the laser diode. If the temperature of the player reaches 167˚F (75˚C), the heat detection circuit will shut off the player and “TOO HOT”...
Page 34 Pressing and holding the bottom ( b ) or top ( a ) half of the “SEEK” button will scroll backward and forward respectively through the tracks. How to fast forward or reverse your CD player To quickly search for a particular point in a selection, press the “FF”...
Page 35 How To Take Care of and Clean Your CD Player and Discs To ensure the continued performance of your Ford Compact Disc Player, carefully read the following precautions: Always handle the disc by its edge. Never touch the playing surface.
Page 36 Before playing, inspect the disc for any contamination. If needed, clean the disc with an approved disc cleaner, such as the Discwasher Compact Disc Cleaner or the Allsop 3 Compact Disc Cleaner, by wiping from the center out to the edges. Do not use a circular motion to clean.
Page 37 CD format. Because of this, a new disc that is free of dust and scratches could be defective and may not play on your Ford Compact Disc Player. If play does not begin once the disc has been inserted: The radio is not on.
Page 39 Using the Controls on Your New Radio How to turn the radio on and off Press the “POWER” button to turn the radio on. Press it again to turn it off. How to adjust the volume Press the ( / ) side of the “VOL” button to increase/decrease the volume.
Page 40 How to tune radio stations There are four ways for you to tune in a particular station. You can manually locate the station using the “SCAN/TUNE” button, “SEEK” the station, “SCAN” to the station or select the station by using the memory buttons, which you can set to any desired frequency.
Page 41 Using the “SCAN” function Pressing the “SCAN/TUNE” button once enters the scan mode (display will indicate “SCN”). Pushing the right ( a ) side of the “SEEK” button will begin the scan mode up the frequency band, stopping on each listenable station for approximately a five-second sampling.
Page 42 Using the Automatic Memory Load feature You can activate the Auto Memory Load feature by pressing and holding the “AUTO PRESET” button for approximately three seconds. Auto Memory Load sets all memory buttons in AM, FM1 and FM2 sequentially by seeking out the first five strong stations for the respective band and storing them in memory buttons 1-5.
Page 43 To deactivate the Auto Memory Store mode and return to the manually-set memory button stations (or those stations set using Auto Memory Load), simply push the “AUTO PRESET” button. Display will show “AUTO” then “OFF.” The next time Auto Memory Store is activated on that band, the radio will store the next set of five strong stations.
Page 44 Adjusting speaker fader Fade control allows you to adjust the sound distribution between the front and rear speakers. Push the “AUDIO” button repeatedly until the display reads “FADE.” Push the “+” side of the “VOL” button to shift the sound to the front speakers, and push the “-”...
Page 45 How to locate a desired track on the tape There are four ways to quickly locate a desired selection on the tape. You can use the fast forward, rewind, “SEEK” or “SCAN” function. Following are brief descriptions of each. Fast forwarding the tape To fast forward the tape, press the “FF”...
Page 46 Whirling sprockets in the display l indicate the direction of tape travel. Using the “SCAN” function with your cassette tape player Press the “SCAN/TUNE” button to enter the scan mode (display indicates “SCN”). Pushing the right a side of the “SEEK” button will begin the forward scan mode on the tape currently playing, stopping on each tape selection for approximately an...
Page 47 How to store the tape Press the “AM/FM” button to stop the tape player and resume radio play. The cassette will be stored in the tape player and the X symbol in the display will be lit until you push the “PLAY PROG”...
Page 48 In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: Using a Ford or equivalent cassette cleaning cartridge to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
Page 49 Protect cassettes from exposure to direct sunlight, high humidity and extreme heat or cold. If they are exposed to extreme conditions, allow them to reach a moderate temperature before playing. If a tape is loose inside the cassette, tighten it before playing by putting your finger or a pencil into one of the holes and turning the hub until the tape is tight.
Page 52 Electronic Stereo and Stereo Cassette Radios Using the Controls on Your New Radio How to tune radio stations (Stereo Radio) There are three ways for you to tune in to a particular station. You can manually locate the station by using the “TUNE” button, “SEEK” the station or select the station by using the memory preset buttons, which you can set to any desired frequency.
Page 53 Using the “AMS” function to manually tune your radio (Stereo Cassette Radio) You can change the frequency up or down one increment at a time by first pressing the “AMS” button (display shows “TUNE”) then within approximately five seconds pressing and releasing either the right ( a ) or left ( b ) side of the “SEEK”...
Page 54 1. Select a band, then select a frequency. 2. Press one of the memory preset buttons and hold the button until the sound returns. That station is now held in memory on that button. 3. Follow the two steps above for each station memory preset button you want to set.
Page 55 How to eject the tape To stop the tape and eject the cassette, press the “i” button. The radio will resume playing. Using the Dolby B noise reduction feature Push the k button to activate. Push again to deactivate. NOTE: Noise reduction system manufactured under license from Dolby Labs Licensing Corporation.
Page 56 In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: Using a Ford or equivalent cassette cleaning cartridge to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
Page 57: Rear Seat Radio Controls
Rear Seat Radio Controls Using the Rear Seat Radio Controls Rear seat radio controls are available on some Aerostar models. The rear seat radio controls are located behind the driver on the left hand side of the vehicle. These controls duplicate several radio functions of the radio and allow the use of headphones in the vehicle.
Page 58 NOTE: Rear seat control volume can be set no higher than current radio setting unless speakers are turned off. See note under How to turn the speakers on and off. Setting the AM or FM frequency band Push the “BAND” button to change the frequency band.
Page 59 Using headphones with the rear seat controls Two 3.5 mm headphone jacks have been provided on the rear seat controls. Plug headphone(s) into the provided jack(s) to operate. Common Radio Reception Conditions Several conditions prevent FM reception from being completely clear and noise-free, such as the following: 1.
Page 60 “shadow” of the structure will allow the station to return to normal. When the radio waves are reflected off objects or structures, the reflected signal cancels the normal signal, causing the antenna to pick up noise and distortion. Cancellation effects are most prominent in metropolitan areas, but also can become quite severe in hilly terrain and depressed roadways.
Page 61 Ask your dealer for a copy of this limited warranty. Service At Ford, we stand behind our audio systems with a comprehensive service and repair program. If anything should go wrong with your Ford audio system, return to your dealer for service.
Page 62: Controls And Features
Controls and Features The main controls for the climate control system, clock, and radio are on the instrument panel.
Page 64 NOTE: Any cleaner or polish that increases the gloss (shine) of the upper part of the instrument panel should be avoided. The dull finish in this area is to help protect the driver from undesirable windshield reflection. The Climate Control Systems Your vehicle is equipped with a control assembly designed to handle either a combination A/C-Heater System or a...
Page 65 Air Conditioner and Heater (If equipped) The control for your air conditioner and heater system is located near the center of the instrument panel and operates only when the ignition key is turned to the ON position. Your air conditioner and heater heats or cools your vehicle interior depending on the function and the temperature you select.
Page 66 Fan speed adjustment The left knob or upper left knob with the x is the fan speed knob. Rotate the x knob to the right to increase fan speed and increase the amount of air entering the vehicle. Four fan speed positions are available.
Page 67 Select MIX to direct air to the floor and windshield defrosters at the same time. If the outside temperature is about 50˚F (9˚C) or warmer, the air will also be dehumidified to remove moisture. This feature will help prevent fogging in humid weather. The air can be cooled or heated.
Page 68 Standard Heater The control for your heater system is located near the center of the instrument panel and operates only when the ignition key is turned to the ON position. The heater heats and/or ventilates your vehicle interior depending on the function and temperature you select.
Page 69 To turn the heater system on, rotate the SELECT knob to any position except OFF. This turns on the fan and allows airflow into the vehicle. Temperature selection The TEMP knob is the rotating knob located at the center of the control with tapered red and blue bands surrounding most of the knob.
Page 70 Operating Tips The following tips will help you to get the most satisfaction from your heater system. In humid weather, select V before starting your engine. This will help to prevent windshield fogging. After a few minutes, you may select another airflow position. To prevent humidity buildup inside your vehicle, always drive with the heater system turned on.
Page 71 Front control assembly with rear blower knob In addition, an auxiliary unit fan switch is located on the left side of the vehicle in line with the second row of seats. To control the auxiliary unit fan speed with this switch, the rear fan switch on the front control must first be set at the REAR CONT (control) position.
Page 72: Rear Window Defroster
Rear Window Defroster (If equipped) The defroster for the rear window clears frost, fog, or thin ice from both the inside and outside of the rear window. The control switch is located on the instrument panel to the right of the steering column. Rear window defroster switch To defrost the rear window: 1.
Page 73 NOTE: Never use sharp instruments or window cleaners with abrasives to clean the inside of your rear window. If you do, you may damage the heating elements that are bonded to the inside of the rear window and cause damage to the rear window defroster.
Page 74: The Interior And Exterior Lights
The Interior and Exterior Lights Turning On the Exterior Lights To turn on your headlamps, parking lamps, marker lamps, license plate lamps and tail lamps, use the headlamp switch to the left of the steering column. Master lighting switch...
Page 75 Daytime Running Light System (Canadian vehicles only) The Daytime Running Light (DRL) system turns the high beam headlamps on, with a reduced light output, when: The headlamp system is in the OFF position, The vehicle is running, and The vehicle has a fully released parking brake.
Page 76 High-mount brakelamp Illuminated Entry System (If equipped) If your vehicle is equipped with this option, the interior courtesy lamps and dome lamp will light when either outside front door handle is raised. They will turn off automatically after approximately 25 seconds or when the ignition key is turned to ON or ACC.
Page 77 Clock Controls on Electronic Radios The electronic radios have a built-in clock. For complete operating instructions, refer to the Electronic Sound Systems chapter in this Owner Guide. Ignition Understanding the Positions of the Ignition The positions of the key in the ignition lock cylinder. ACCESSORY allows some of your vehicle’s electrical accessories such as the radio and the windshield wipers to operate while the engine is...
Page 78 make sure they work before you start the engine. The key returns to the ON position once the engine is started and remains in this position while the engine runs. START cranks the engine. Release the key once the engine starts so that you do not damage the starter.
Page 79: Windshield Wipers And Washer
corrected as soon as possible, but make sure that you use the accepted hand signals in the meantime. High Beams and Flashing the Lamps Headlamp high beam and flash-to-pass operation Windshield Wipers and Washer To turn on the windshield wipers, the ignition key must be turned to the ON or ACC position.
Page 80: Gearshift Lever
Devices such as shields are not recommended for your Ford vehicle. Do not try to clean the windshield when the washer fluid container is empty or activate the washers at any time for more than 15 seconds continuously.
Page 81: Hazard Flasher Switch
Overdrive off button OVERDRIVE OFF Light on Gearshift Lever This light indicates the operating range of the transmission. The word OFF illuminates on the lever when the OVERDRIVE OFF button is depressed. Hazard Flasher Switch The hazard flasher switch is located on the top of the steering column.
Page 82 Tilt Steering (If equipped) RWARNING Never adjust the steering wheel when the vehicle is moving. Turn signal and tilt steering release lever To change the position of the steering wheel, pull the release lever on the column toward you. Tip the steering wheel to the desired position. Release the lever to lock the steering wheel in place.
Page 83 Speed Control (If equipped) Speed control switches on the steering wheel To Turn Speed Control Off Press OFF Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To Turn Speed Control On Press ON To Set A Speed Press the SET ACCEL.
Page 84 you may want to shift to the next lower gear to reduce your vehicle’s speed. If your vehicle slows down more than 10 mph (16 km/h) below your set speed on an uphill, your speed control will disengage. Pressing RESUME will re-engage it. RWARNING Do not use the speed control in heavy traffic or on roads that are winding,...
Page 85 RWARNING Do not shift the transmission into N (Neutral) with the speed control on. To Disengage Speed Control Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. To Return to a Set Speed Press RESUME.
Page 86 The map lamps are located inside the dome lamp assembly, on each side of the dome lamp. Each lamp has its own switch. The front dome lamp, cargo lamp and stepwell lamp, if so equipped, will operate as courtesy lamps when either of the front doors, side cargo door, liftgate or dual rear door is opened.
Page 87 Doors Door Handles and Locks Inside handles Outside handles and locks...
Page 88 Anti-theft front door lock knobs Anti-theft lock knobs are designed to preclude unlocking the door by pulling up on the bullet type lock knob. To unlock and open the front door from the inside of the vehicle, pull on the inside door handle.
Page 89 Opening the liftgate Make certain that you close the liftgate door and window before driving your vehicle. If you do not, possible damage may occur to the liftgate door lift cylinders and attaching hardware. RWARNING Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle.
Page 90 3. You can lock the liftgate latch by pushing down the lock button before you pull down and close the liftgate. You can also lock the liftgate latch by inserting your vehicle’s door key and turning it clockwise after you have closed the liftgate, or by using the power door locks (if equipped).
Page 91 When closing the dual rear cargo doors, remember to close the left rear door first. RWARNING Do not operate your vehicle with the rear double doors open. Power Door Locks (If equipped) The power door lock switches are located in the front doors.
Page 92 Power door lock controls Windows Sliding side windows To open or close the sliding side windows, follow the instructions listed below. Opening the sliding window 1. To open the window, pull the rear portion of the latch handle rearward. 2. Slide the window open. Closing the sliding window 1.
Page 93 Opening the sliding side window Using the Power Windows (If equipped) Each front door has a power control that opens and closes the window on that door. The driver’s door has a master control switch that operates both front door windows. You must place the ignition switch in the ON or ACC position to use your power window controls.
Page 94 Power window controls — driver-side shown Mirrors For vehicles without rear door windows, the right-hand side mirror is a flat glass mirror. All other vehicles have convex right-hand side view mirrors. Convex mirrors have a curved surface and will show a wider view of the lane next to and behind your vehicle.
Page 95 4. Return the center switch to the middle position to keep the mirror in place. Power mirror control Do not clean the plastic housing of any electric mirror with gasoline or other petroleum-based cleaning products. Console Your vehicle may have a full console. The full console has the features shown in the illustration below.
Page 96 The features on the console Garage Door Opener Storage At the center of the console, a compartment is provided for storage of a garage door opener transmitter. In its stored position, the transmitter can be activated by pressing on the compartment door.
Page 97 3. Remove the backing from the self-adhesive side of the Velcro console) and apply it to the back of your transmitter. 4. Install your transmitter into the compartment, making sure the actuator button of your transmitter is in line with one of the pegs on the door when the door is closed (Figure 2).
Page 98 5. Once the transmitter is installed, the actuation peg on the door in line with your transmitter button may need to be adjusted for proper function. This can be done using the button height adjustment pegs (located on the compartment door). Add one peg at a time until pressing the door actuates the transmitter button (Figure 3).
Page 99: Seating And Safety Restraints
Seating and Safety Restraints Seats Adjusting the Front Seat Manually You can move the driver seat forward or backward. If your vehicle is equipped with the optional reclining bucket seat, you can also tilt the seatback up to 30 degrees rearward. The front passenger seat cannot be adjusted.
Page 100 RWARNING Always drive and ride with your seatback upright and the lap belt snug and low across the hips. RWARNING Children should always ride with the seatback in the fully upright position. To move the seat forward or backward: To recline the seatback:...
Page 101 E-Z Access Operation — Passenger Side Rear Captain’s Chair (Optional Quad Buckets) To provide easy access to the rear of the vehicle, the passenger side rear captain’s chair can be tilted forward. To tilt seat forward: 1. Put the seatback in the upright position. 2.
Page 102 To install the rear bucket seat: 1. Lift the seat assembly into the vehicle and drop the front and rear floor hooks into the floor wells at a point just behind the floor attachment pins. 2. Rotate the seat latch handle forward, causing the J hook to engage over the front of the foremost well retainer.
Page 103 To remove seat assembly: 1. Disengage the lap/shoulder safety belt from the seat by inserting a key or screwdriver into the slot in the detachable anchor and lifting upward. Stow the tongue end of the detachable anchor as shown in the illustration.
Page 104 Rear seat shoulder safety belt — stowage (with seat removed)
Page 105 RWARNING When reinstalling a rear seat in your vehicle it must be placed in its original position. Improper installation of the seat will prevent correct use of the safety belts and could increase the risk of injury. Refer to the warning label on the seat belt.
Page 106 4. Ensure that the latch handles are fully seated in the down position. 5. Before you engage the safety belt, be sure it is not twisted. A twisted safety belt may cause the retractor to work improperly. Remove any twist, then insert the tongue end of the detachable anchor into the detachable anchor until you hear a “snap”...
Page 107 Installation and removal of the second and third passenger bed and bench seat RWARNING Never adjust the driver’s seat or seatback when the vehicle is moving. RWARNING Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop.
Page 108 Seat/bed conversion (If Equipped) Vehicles equipped with the seat/bed can be either a two passenger or three passenger seat. To convert the seat/bed to a bed: 1. Pull up the release lever located on right hand side of the seat, and at the same time push the seatback rearward.
Page 109 Manual lumbar knob Underseat Stowage Drawer (If equipped) If your vehicle is equipped with the front passenger seat drawer, open it by moving the latch lever upward and pulling the drawer toward the front of the vehicle. To remove the drawer, pull past the stop tab on the back of the drawer.
Page 110 Underseat stowage drawer — RH front passenger seat only Important Safety Belt Information The use of safety belts helps to restrain you and your passengers in case of a collision. In most states and in Canada, the law requires their use. Safety belts provide best restraint when: the seatback is upright the occupant is sitting upright (not slouched)
Page 111 See the following sections in this chapter for directions on how to properly use these safety belts. Also see Safety Restraints for Children in this chapter for special instructions about using safety belts for children. RWARNING Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Page 112: Combination Lap And Shoulder Belts
RWARNING Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. RWARNING Lock the doors of your vehicle before driving to lessen the risk of the door coming open in a collision.
Page 113 Fastening the front seat combination lap and shoulder belt NOTE: Be sure to read and understand Important Safety Belt Information at the beginning of this chapter. Unfastening the combination lap and shoulder belts — front and rear outboard seating positions While the belt retracts, guide the tongue to its original position to prevent it from striking you or the vehicle.
Page 114 Dual locking mode retractors operate in two ways: Vehicle sensitive (emergency) locking mode In this operating mode, the shoulder belt retractor will allow the occupant freedom of movement, locking tight only on hard braking, hard cornering or impacts of approximately 5 mph (8 km/h) or more.
Page 115 3. A clicking sound will continue to be heard as the belt is allowed to retract. This indicates that the retractor is in the automatic locking mode. NOTE: When the combination lap/shoulder belt is unbuckled and allowed to retract completely, the retractor will switch to the vehicle sensitive (emergency) locking mode.
Page 116 Disengaging safety belt for rear seat removal Whenever a rear seat has been removed, the tongue end of the detachable anchor must be correctly stowed. See the following illustration.
Page 117 Rear seat shoulder safety belt — stowage (with seat removed)
Page 118: Lap Belts
RWARNING When reinstalling a rear seat in your vehicle it must be placed in its original position. Improper installation of the seat will prevent correct use of the safety belts and could increase the risk of injury. Refer to the warning label on the seat belt.
Page 119 Pull the belt across your hips and insert the tongue into the correct buckle on your seat until you hear a snap and feel it lock. Make sure the buckle is securely fastened. If you need to lengthen the belt, unfasten it and tip the belt tongue at a right angle to the belt.
Page 120: Safety Belt Maintenance
(if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after any collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision...
Page 121 3. Pull the belt out of its holder as far as it will go and untwist the belt or remove the object that is jamming the belt. Let the belt retract. 4. Then, pull the belt out and let it retract several times to make sure that the belt works properly.
Page 122 1. Grasp the belt webbing at the “D” ring. See Figure 2.
Page 123 2. Rotate and fold the belt webbing over itself as required to remove the twist. 3. Feed the folded portion of the belt through the “D” ring. 4. When completed, the safety belt should look like Figure 3.
Page 124 Air Bag Supplemental Restraint System (SRS) Important Air Bag Precautions Your vehicle is equipped with a supplemental restraint system designed to work with the safety belts to help protect you and your right front seat passenger in the event of certain collisions described in the section “How Does the Air Bag Supplemental Restraint System Work?”...
Page 125 RWARNING Do not attempt to service, repair, or modify the air bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. RWARNING If you are close to an inflating air bag, it could seriously injure you.
Page 126 Children and Air Bags Children should be placed in the rear in an appropriate child safety seat that is properly secured to the vehicle. RWARNING Children should always wear their safety belts. Failure to follow these instructions may increase the risk of personal injury in the event of a collision.
Page 127 NOTE: For additional important safety information on the proper use of seat belts, child seats, and infant seats, please read the entire Safety Restraints chapter in this owner guide. How Does the Air Bag Supplemental Restraint System Work? The Air Bag Supplemental Restraint System is designed to activate when the vehicle sustains sufficient longitudinal (lengthwise) deceleration that is equal to or greater than hitting an...
Page 128 RWARNING The air bag will inflate only once. The system is designed to function on a one-time-only basis. If the air bag is inflated, THE AIR BAG WILL NOT FUNCTION AGAIN AND MUST BE REPLACED IMMEDIATELY. If the air bag is not replaced, this will increase the risk of injury in a subsequent collision.
Page 129 If any of these things happen, even intermittently, have the Air Bag Supplemental Restraint System serviced at your Ford or Lincoln-Mercury dealer immediately. Unless serviced, the system may not function properly in the event of a collision.
Page 130: Safety Restraints For Children
Disposal of Air Bags and Air Bag Equipped Vehicles For disposal of air bags or air bag equipped vehicles, see your local Ford or Lincoln-Mercury dealer. Air bags MUST BE disposed of by qualified personnel. Safety Restraints for Children In the U.S. and Canada, you are required by law to use safety restraints for children.
Page 131 RWARNING It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 132 Ford recommends placing forward-facing safety seats in the second row and using safetey seats with top tether straps for added protection.
Page 133 All child restraint systems are designed to be secured in vehicle seats by lap belts or by the lap portion of a lap-shoulder belt. RWARNING If you do not properly secure the safety seat, the child occupying the seat may be injured during a collision or sudden stop.
Page 134 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. See Figure 2. Be sure the belt webbing is not twisted, and insert the tongue into the buckle. See Figure 3.
Page 135 Routing the lap/shoulder belt Buckling the belt...
Page 136 4. Grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. At this time, the retractor is in the automatic locking mode (child seat restraint mode). See Figure 4. Setting the retractor to automatic locking mode 5.
Page 138 6. Before placing the child in the child seat, forcibly tilt the seat from side to side, and tug it forward to make sure that the seat is securely held in place. See Figure 7. Checking that the seat is secure 7.
Page 139 Checking the retractor 8. Check to make sure that the child seat is properly secured prior to each use. If the retractor is not locked, repeat steps 4 through 7. NOTE: To remove the retractor from automatic lock mode, allow seat belt to retract fully to its stowed position and the retractor will automatically switch back to the vehicle sensitive locking mode...
Page 140 Installing Child Safety Seats at the Rear Center Seating Position with Locking Adjustable Lap Belt DO NOT install a forward-facing child safety seat in the third row center seating position. Forward-facing seats must be installed with a lap/shoulder belt, or a lap belt and top tether strap.
Page 141 You can attach a tether strap anchor bracket to the rear floor by using a tether anchor kit (613D74), available at no charge from any Ford dealership. Read and carefully follow the instructions provided with the kit for installation of the child tether strap anchor.
Page 142 Until a floor anchor is installed, follow these steps to install a tethered child safety seat in the front seat: 1. Buckle the lap/shoulder belt in the seat directly behind the front passenger seat. 2. Pull all the stored belt out of the rear seat belt retractor to switch the retractor to automatic locking mode.
Page 143 Built-In Child Seat (If equipped) The second row bench seat may include an optional built-in child safety seat. This child restraint is to be used only by children who are at least one year old, weigh between 22 and 60 pounds (10 and 27 kilograms) and whose shoulders (top) are below the shoulder harness slots in the seatbacks with the headrest in the...
Page 144 RWARNING Failure to follow all of the instructions on the use of this child restraint system can result in your child striking the vehicle’s interior during a sudden stop or crash. How to use the Built-In Child Seat Read the following procedures and all of the labels on the Built-In Child Seat before using the seat.
Page 145 Figure 2 3. Read the information and warnings on the child seat. Check the child’s size, weight and age to be sure the child is not too small or too large for the child seat. Refer to Figure 3.
Page 146 Figure 3 4. Pull up on the two black looped straps at the upper corners of the child seat to unsnap the cushion protector flap. 5. Lower the seat cushion. 6. Pull the lap and shoulder belts cinch release strap while pulling the shoulder belts fully out.
Page 147 Figure 4 Figure 5 6. If connected, squeeze the top and the bottom of the right half of the chest clip and pull to separate both halves. 7. Place the child on the child seat and position the shoulder belts over each shoulder. Refer to Figure 6.
Page 148 Figure 6: Shoulder safety belt placement on the child 8. Insert either the left or right safety belt tongue into the single opening of the crotch belt buckle as shown in Figure 7. (It does not matter which tongue is inserted first.) Then insert the other tongue.
Page 149 9. Fasten both halves of the chest clip below the child’s shoulders and adjust it to comfortably hold the shoulder belts in place on the child’s chest. The purpose of this clip is to position the shoulder belts correctly on the child’s shoulders.
Page 150 Figure 9: Checking for securely latched buckle and locked retractor 11. If the shoulder belts are pulled too tight, pull on the lap and shoulder belts cinch release strap to loosen the shoulder belts on the child’s shoulders. Refer to Figure 4. Then retighten the lap and shoulder adjustment belt per Step 10 above.
Page 151 If the child seat was in use during a collision, Ford recommends replacing it. However, if the collision was minor and a qualified technician finds that the child restraints do not show damage and continue to operate properly, they do not need to be replaced.
Page 152 Built-in child seat maintenance Regularly inspect the lap and shoulder belts system of your child seat. See your Ford dealer if the shoulder belt webbing is frayed, or if the buckle and tongue are damaged and/or do not function properly.
Page 153 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and...
Page 154: Starting
Starting Fuel-Injected Engines When starting a fuel-injected engine, the most important thing to remember is to avoid pressing down on the accelerator before or during starting. Only use the accelerator when you have problems getting your vehicle started. See Starting Your Engine in this chapter for details about when to use the accelerator while you start your vehicle.
Page 155 Starting Your Engine To start your engine: 1. Follow the steps under Preparing to Start Your Vehicle at the beginning of this section. 2. Turn the ignition key to the ON position. 3. DO NOT depress the accelerator pedal when starting your engine.
Page 156: Roadside Emergencies
Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. After starting, allow the engine to idle for a few seconds before driving away. NOTE: Your vehicle is equipped with a brake-shift interlock feature.
Page 157 If the engine still does not start after two attempts: 1. Turn the ignition key to the OFF position. 2. Press the accelerator all the way to the floor and hold it. 3. Turn the ignition key to the START position. 4.
Page 158 RWARNING Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. If you consistently start your vehicle in subzero temperatures, use an engine block heater (if your vehicle has this option).
Page 159 If the Engine Cranks but Does Not Start or Does Not Start After a Collision Fuel Pump Shut-Off Switch If the engine cranks but does not start or does not start even after a small collision, the fuel pump shut-off switch may have been activated. The shut-off switch is a device intended to stop the fuel pump when your vehicle has been involved in a substantial jolt.
Page 160 If your engine cranks but does not start after a collision or substantial jolt: 1. Turn the ignition key to the OFF position. 2. Check under the vehicle for leaking fuel. 3. If you do not see or smell fuel, push the red reset button down.
Page 161 Guarding Against Exhaust Fumes Carbon monoxide, although colorless and odorless, is present in exhaust fumes. Take precautions to avoid its dangerous effects. RWARNING If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes.
Page 162 AIR CONDITIONING — Set the fan speed knob at MEDIUM or HIGH, the function selector knob on NORM A/C or MAX A/C and the temperature control knob on any desired position. Removing the Key From the Ignition 1. Put the gearshift in P (Park). 2.
Page 163: Driving
Driving Brakes Front Disc Brakes The front disc brakes are self-adjusting. They do not require service other than periodic inspection for pad wear. Rear Drum Brakes The rear drum brakes are self-adjusting. Automatic adjustment occurs when the brakes are applied while “backing up.” If normal operation does not include much backing, adjust the brakes when they seem “low,”...
Page 164 Rear Anti-lock Brakes Your vehicle is equipped with a rear Anti-lock Brake System (ABS). This system prevents at least one and often both rear wheels from completely locking up when the brakes are applied in a panic stop, for example. Even with the Anti-lock Brake System, you should be careful when braking.
Page 165 If during normal operation the brake pedal seems “low”, it may indicate the need for a brake system inspection and/or service. You should have your brakes checked as soon as possible. Occasional brake squeal during light to moderate stops does not affect the function of the brake system and is normal.
Page 166 Applying the Brakes Apply the brake pedal gradually. Use the “squeeze” technique — push on the brake pedal with a steadily increasing force. This allows the wheels to continue to roll while you are slowing down, which lets you steer properly. NOTE: If you are driving down a long or steep hill, shift to a lower gear and do not apply your brakes continuously.
Page 167 Parking Brake RWARNING Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle. RWARNING If the parking brake is fully released, but the Brake System light remains on, have the brakes checked immediately.
Page 168: Automatic Transmission
Steering Your Vehicle Your vehicle comes with power steering. Power steering uses energy from the engine to help steer your vehicle. If the amount of effort needed to steer your vehicle changes at a constant vehicle speed, have the power steering system checked. If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually but it takes more effort.
Page 169 Indicator Light (TCIL) (O/D OFF), which is located on the gearshift lever, may flash steadily if a malfunction has been detected. If the TCIL is flashing, contact your Ford dealer as soon as possible. If this condition persists, damage to the transmission could occur.
Page 170 Power Braking Increasing the engine speed above idle without vehicle movement (such as holding the brake) in a forward or reverse gear causes transmission stall. NOTE: Continued operation in the stall condition can result in transmission overheat, malfunction or fluid expulsion.
Page 171 RWARNING Hold the brake pedal down while you move the gearshift lever from position to position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. Once you place the gearshift securely into position, gradually release the brake pedal and use the accelerator as necessary.
Page 172 4. Apply the brake pedal and shift to N (Neutral). (If the vehicle is shifted back to P [Park], you must repeat the previous steps.) 5. Start the vehicle. If you need to shift out of P (Park) by using the alternate procedure described above, it is possible that a fuse has blown and that your brakelamps may also not be functional.
Page 173 RWARNING Never leave your vehicle unattended while it is running. R (Reverse) With the gearshift in the R (Reverse) position, the vehicle will move backward. You should always come to a complete stop before shifting into or out of R (Reverse). N (Neutral) With the gearshift in the N (Neutral) position, the vehicle can be started and is free to roll.
Page 174 When to use Drive You will note there is not a drive position on your gearshift indicator. However, you will find a transmission control switch labeled OVERDRIVE OFF located on the end of the gearshift lever. Press this switch and the indicator light (OFF) illuminates on the gearshift lever.
Page 175 When to use 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. This position provides 2 (Second) gear operation only. When to use 1 (Low) Use 1 (Low) to provide maximum engine braking on steep downgrades.
Page 176 When to use Drive You will note there is not a drive position on your gearshift indicator. However, you will find a transmission control switch labeled OVERDRIVE OFF located on the end of the gearshift lever. With overdrive canceled and the OVERDRIVE OFF illuminated, the transmission will operate in gears one through four.
Page 177 Forced Downshifts To gain acceleration in j (Overdrive) or Drive (Overdrive off) when passing another vehicle, push the accelerator to the floor. The transmission will downshift to the appropriate gear: fourth, third, second or first gear. Traction-Lok Rear Axle (If equipped) This axle provides added drive away traction on slippery surfaces, particularly when one or more wheels are on a surface with poor traction.
Page 178 How the Electronic 4-Wheel Drive (E-4WD) System Works Under normal driving conditions, when the road is firm, dry and level, the engine power is distributed one-third to the front axle and two-thirds to the rear axle. However, if a wheel begins to slip, the microprocessor will sense this condition and signal the system to transmit more power to the axle with more traction.
Page 179 Do not let the added driving traction of E-4WD lead you to believe that you can stop any quicker than a conventional two-wheel drive vehicle. The added traction performance does not improve the braking ability of the E-4WD vehicle. Allow the same amount of distance when braking as with a two-wheel drive vehicle.
Page 180 RWARNING Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label. Vehicle/Trailer Loads All vehicles may tow a Class I trailer provided the Gross Combined Weight (GCW) is less than or equal to the GVWR shown on the Safety Compliance Certification Label.
Page 181 Standard length vehicles adapted for trailer tow may require relocation of the underbody spare tire. It is recommended that you secure the tire under the rear-most seat using the hold-down hardware located with the jack. Spare tire stowage (standard length model) Do not tow a trailer until your vehicle has been driven at least 500 miles (800 km).
Page 182 Trucks, unlike passenger cars, are basically custom vehicles designed to carry a load. Most owners start with a base vehicle and add production and dealer installed and/or aftermarket components to suit their tastes and purposes. Even trucks that are purchased for personal transportation only are likely to have considerable optional equipment, such as step bumpers and light bars, for example.
Page 183 The following is a typical example of a Safety Compliance Certification Label and an explanation of how this information should be used: Safety Compliance Certification Label Do not use the sample numbers on the Safety Compliance Certification Label shown. Use the actual numbers from your vehicle certification label.
Page 184 GAWR (Gross Axle Weight Rating) GAWR F (Gross Axle Weight Rating Front) GAWR R (Gross Axle Weight Rating Rear) GCWR (Gross Combined Weight Rating) Maximum Trailer Weight Rating Maximum Trailer Weight Trailer Weight Range Base Curb Weight The Base Curb Weight is the weight of the vehicle including fuel, coolants, lubricants, emergency tools, spare wheel and tire.
Page 185 Gross Axle Weight Rating (GAWR) We have all seen a car or a truck that is loaded down in the rear and riding high in the front. This is a dangerous condition that usually means that the rear suspension components are under severe strain and that vehicle handling is impaired.
Page 186 With the tires inflated to the specified pressure, the total weight of your vehicle must not exceed the GVWR and GAWR specified on the Safety Compliance Certification Label. This includes full fuel tank(s), vehicle equipment, and occupants as well as the cargo load. GCWR (Gross Combined Weight Rating) GCWR is the maximum combined weight of the towing vehicle (including passengers and cargo)
Page 187 Calculating The Load To know how much weight your vehicle can carry: Obtain ratings from your Safety Compliance Certification Label, and the Trailer towing specifications in the Owner Guide (refer to the Index) — Refer to the following sample illustration to locate the various ratings on your Safety Compliance Certification Label.
Page 188 Use this chart to perform your calculations. NOTE: The Truck Safety Compliance Certification Label has two weight related entries that sometimes cause confusion. Front Axle Reserve Capacity in Pounds (kgs): If this value is given as 83 pounds (38 kgs) on the label, does this mean that you are limited to adding only 83 pounds (38 kgs) of accessories to the front end capacity? Not exactly.
Page 189 that you can load 83 pounds (38 kgs) of options on the front axle, add 150 pound (68 kgs) passengers to all seating positions, and add evenly distributed cargo in the box without exceeding the GAWR F. It is possible to hang heavier equipment on the front as long as the vehicle owner/operator compensates.
Page 190 If your vehicle exceeds the GVWR, remove cargo from your vehicle accordingly. If your vehicle exceeds the GAWR for either axle, shift the load or remove cargo accordingly. RWARNING Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label.
Page 193 Automatic Transmissions Preparing to Tow For your safety and for the good of your vehicle, use the right equipment for the type of trailer you tow. Also, make sure that all towing equipment is properly attached to your vehicle.
Page 194 If you are not certain that you are using the right equipment in the proper manner, see your Ford or Lincoln-Mercury dealer. Under certain circumstances, the trailer frontal area is not to exceed the base vehicle frontal area, no matter what size engine your vehicle...
Page 195 Trailer Brakes Separate trailer brakes are required on most towed vehicles weighing over 1,500 lb (680 kg). RWARNING Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase.
Page 196 If you use the speed control while you are towing on very long, steep grades, the speed control may shut off. When towing a trailer in hilly terrain, with a vehicle equipped with an automatic overdrive transmission, you may wish to operate in Drive (by cancelling Overdrive with OVERDRIVE OFF button) rather than j (Overdrive).
Page 197 Allow more room for stopping with a trailer attached. Trailer brakes should be applied first, whether manually or automatically controlled, when approaching a stop. For a good handling truck-trailer combination, the trailer tongue load should be approximately 10-15% of the loaded trailer weight. Make a thorough check of your equipment before starting out on the road.
Page 198 With the chocks in place, release the brake pedal, making sure the chocks are holding. Apply the parking brake by pressing the brake pedal down firmly with your right foot while applying the parking brake with your right hand. Shift the gearshift lever into P (Park). To start, after being parked on a grade: Apply the brake pedal and hold.
Page 199: Roadside Emergencies
Roadside Emergencies Hazard Flasher The hazard flasher is used to alert other drivers to hazardous situations. The flashers will continue to flash with the brake pedal depressed. The flashers work whether your vehicle is running or not. The flashers work for up to two hours when the battery is fully charged and in good condition without draining the battery excessively.
Page 200 If the Engine Cranks But Does Not Start or Does Not Start After a Collision The Fuel Pump Shut-off Switch If the engine cranks but does not start or if you have had a collision, the fuel pump shut-off switch may have been triggered. The shut-off switch is a device that stops the fuel pump when your vehicle has been involved in a substantial jolt.
Page 208 To remove and replace a fuse, use the fuse puller provided. The side view of a fuse RWARNING Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Page 209: Changing A Tire
Circuit Breakers If you need to check a circuit breaker, locate the fuse panel first. Otherwise, locate the circuit breaker according to the instructions on the charts given earlier in this chapter. However, you should know that the circuit breakers will reset themselves and allow the electrical parts to work again once the overload on the circuit is removed.
Page 210 The Temporary Spare Tire You may have a high pressure temporary spare tire. This spare tire is smaller than a regular tire and is designed for emergency use only. Use it only when you get a flat tire and replace it as soon as you can.
Page 211 When you drive with the temporary spare tire, DO NOT: exceed 50 mph (80 km/h) under any circumstances. load your vehicle so that it is heavier than the maximum vehicle load rating listed on the tire decal. tow a trailer. use tire chains on this tire.
Page 212 If your vehicle is the model with a standard length body or extended length (all models), the temporary spare tire is stowed at the rear of the vehicle under the body. The standard length E-4WD model spare tire is mounted on the floor. To remove underbody temporary spare tire: 1.
Page 213 Temporary spare tire location and assembly To stow underbody temporary spare tire: 1. Insert lug nut wrench into the actuator hole and turn counterclockwise until the cable/retainer is extended for insertion into the wheel. 2. Install the retainer through wheel center with valve stem facing up.
Page 214 3. Rotate wrench clockwise until tire is secured. (Raising mechanism will slip.) 4. Check for proper seating against underbody supports and retighten if necessary. Spare tire — underbody carrier RWARNING Do not stow any conventional spare tire or flat temporary spare tire in the underbody position.
Page 215 2. Position the flat tire, valve stem up, under the rear-most seat and over the “J” bolt attaching bracket on the floor pan. 3. Insert the “J” hook bolt through the center of the wheel and hook on bracket. 4. Install plate over “J” hook bolt and secure with wing nut.
Page 216 Extended van underbody outside spare wheel/flat tire storage RWARNING Make sure the spare tire and jacking equipment are stowed and secured in the proper storage location. Preparing to Change the Tire NOTE: To lift your vehicle by other than the front or rear jacking points, be sure to use only hoist adapters with a wide contact surface.
Page 217 When one of the back wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park). To prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block the wheel (both directions) that is diagonally opposite (other side and end of the vehicle) to...
Page 218 Aerostar extended model jack pack 3. Use the tapered end of the lug nut wrench to unscrew wheel ornaments attached by retaining screws. Remove any wheel trim. Insert the tapered end of the lug nut wrench behind wheel covers or hubcaps and twist off.
Page 219 Removing and Replacing the Tire 1. Positioning the jack a. To raise a front wheel, place the jack under a horizontal portion of the underbody member behind the wheel, as shown. Front jacking point b. To raise a rear wheel, place the jack under a horizontal portion of the underbody member ahead of the wheel as shown.
Page 220 RWARNING Never place the jack under the rocker panels. 2. Remove the lug nuts with the lug nut wrench. 3. Replace the flat tire with the spare tire. 4. Thread the lug nuts on the wheel studs with the beveled face toward the wheel. Use the lug nut wrench to screw the lug nut snug against the wheel but do not tighten.
Page 221 Lug nut tightening sequence RWARNING Never use wheels or lug nuts different than the original equipment as this could damage the wheel or mounting system. This damage could allow the wheels to come off while the vehicle is being driven. 7.
Page 222: Jump-Starting Your Vehicle
Also retighten to the specified torque at 500 miles (800 km) of operation after any wheel change or any time the lug nuts are loosened. RWARNING Failure to retighten wheel lug nuts at mileages specified could allow wheels to come off while the vehicle is in motion. Jump-Starting Your Vehicle Your vehicle’s battery may die if you leave the lights on or any electrical equipment on after...
Page 223 RWARNING Applying too much pressure on the ends when lifting a battery could cause acid to spill. Lift the battery with a carrier or with your hands on the opposite corners. RWARNING Batteries contain sulfuric acid which burns skin, eyes, and clothing. If the acid touches someone’s skin, eyes, or clothing, immediately flush the area with water for at least 15 minutes.
Page 224 2. Do not disconnect the battery of the disabled vehicle. You could damage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehicle. Make sure the vehicles do not touch each other. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts.
Page 225 RWARNING Do not connect the end of the second cable to the negative ( ) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. Attaching jumper cables Jump-Starting 1. Make sure that the jumper cables are not in the way of moving engine parts, then start the booster vehicle.
Page 226 Removing jumper cables 1. Always remove the jumper cables in the reverse order. Remove the negative ( ) end of the jumper cable from the metallic surface on the engine or frame of the disabled vehicle. 2. Remove the negative ( ) cable from the booster battery.
Page 228: Maintenance And Care
Maintenance and Care Service Made Easy Ford has two goals for servicing your vehicle. 1. When we can, we design parts that do not need to be serviced. 2. We want to make servicing your vehicle as easy as possible. To help you:...
Page 229 Motorcraft parts are designed and built to provide the best performance in your vehicle. Using these parts for replacement is your assurance that Ford-built quality stays in your vehicle. NOTE: Always dispose of used automotive fluids in a responsible manner. Follow your community’s standards for...
Page 230 If you disconnect the battery, the engine must “relearn” its idle conditions before your vehicle will drive properly. To find out how the engine does this, see Battery in this chapter. Working with the engine off: 1. Set the parking brake fully and make sure that the gearshift is securely latched in P (Park).
Page 231 Hood release handle 2. While applying downward pressure on the hood, push the hood latch handle located behind the grille near the center front of the vehicle to the left. 3. Disconnect the hood support from the retaining clip on the radiator support and place it into the slot marked PROP in the underside of the hood.
Page 232 Engine Oil Recommendations We recommend using Motorcraft oil or an equivalent oil meeting Ford Specification WSS-M2C153-F and displaying the American Petroleum Institute CERTIFICATION MARK on the front of the container. The API Certification Mark Never use: “Non-Detergent” oils Oils labeled API SA, SB, SC, SD, SE, SF or SG...
Page 233 (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced. It is recommended you use the appropriate...
Page 234 Engine oil dipstick 6. Carefully pull the dipstick out again. If the oil level is below the “ADD 1 QT” line, add engine oil as necessary. If the oil level is beyond the letter “F” in Full, engine damage or high oil consumption may occur and some oil must be removed from the engine.
Page 235: Brake Fluid
Oil change intervals Refer to the Maintenance Schedule booklet for additional information. Brake Fluid Your vehicle is equipped with a brake fluid level indicator in the master cylinder which lights the BRAKE warning light on the instrument panel when the brake fluid level is low. Under normal circumstances, your vehicle should not use up brake fluid rapidly.
Page 236 If the fluid is low, carefully clean and remove the filler cap from the reservoir. Fill the reservoir to the MAX line with Ford High Performance DOT 3 Brake Fluid C6AZ-19542-AB or DOT 3 equivalent fluid meeting Ford specification ESA-M6C25-A.
Page 237: Windshield Washer Fluid
Brake master cylinder reservoir Windshield Washer Fluid Check the level of the windshield washer fluid every time you stop for fuel. The reservoir for the windshield washer fluid is located in the engine compartment. RWARNING Do not put windshield washer fluid in the container for the engine coolant.
Page 238 Use specially formulated windshield washer fluid rather than plain water, because specially formulated washer fluids contain additives that dissolve road grime. For safety reasons, washer fluids containing an appropriate antifreeze such as methanol should be used in freezing weather (temperatures below 32˚F [0˚C]). State or local regulations on Volatile Organic Compounds (VOCs) may restrict use of the most common antifreeze, methanol.
Page 239 Liftgate window washer reservoir Engine Coolant Checking the Engine Coolant NOTE: Be sure to read and understand Precautions When Servicing Your Vehicle at the beginning of this chapter. Your vehicle’s engine coolant protects the engine from overheating in the summer and from freezing in the winter.
Page 240 Adding Engine Coolant Adding engine coolant to reservoir RWARNING Do not put engine coolant in the container for the windshield washer fluid. When the engine is cool, add a 50/50 mixture of engine coolant and water to the engine coolant recovery reservoir —...
Page 241 Ford specification ESE-M97B44-A. Ford Premium Engine Coolant is an optimized formula that will protect all metals and rubber elastomers used in Ford cooling systems for 4 years or 50,000 miles (80,000 km). Do not use alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze.
Page 242 Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter.
Page 243: Power Steering Fluid
NOTE: Due to air being trapped in the 4.0L engine cooling system, it is not unusual to experience a 4 to 7 ounce (120 to 210 ml) coolant loss up to 7,500 miles (12,000 km) after initial system fill. Power Steering Fluid Check the level of the power steering fluid at least twice a year (i.e., every Spring and Fall).
Page 244 Power steering dipstick Power steering reservoir Power steering reservoir...
Page 245: Automatic Transmission Fluid
Do not overfill. 6. When you are finished, put the dipstick back in and make sure that it fits snugly. Use only a power steering fluid such as Ford Power Steering Fluid Motorcraft MERCON ATF. If the power steering fluid is low, do not drive your vehicle for a long period of time before adding fluid.
Page 246 level without having to drive 20 miles to obtain a normal operating temperature if outside temperatures are above 50˚F (10˚C). NOTE: If the vehicle has been operated for an extended period at high speeds or in city traffic during hot weather, or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow the fluid to cool before checking.
Page 247 Adding Automatic Transmission Fluid The fluid type is stamped on the dipstick. Before adding any fluid, be sure that the correct type will be used. Add fluid in 1/2 pint (.25L) increments through the filler tube to bring the level to the correct area on the dipstick.
Page 248 Battery Your vehicle may have a Motorcraft maintenance-free battery. The Motorcraft maintenance-free battery does not require additional water during its life of service. The vents are part of the cover and cannot be removed. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are tightly fastened to the battery terminals.
Page 249 Help Us Protect Our Environment Ford Motor Company strongly recommends that used lead-acid batteries be returned to an authorized recycling facility for disposal. Battery recycling symbol Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery.
Page 250: Wiper Blades
RWARNING Batteries contain sulfuric acid which burns skin, eyes, and clothing. If the acid touches someone’s skin, eyes, or clothing, immediately flush the area with water for at least 15 minutes. If someone swallows the acid, have him or her drink lots of milk or water first, then Milk of Magnesia, a beaten egg, or vegetable oil.
Page 251 If you do not take these precautions, your tires may fail or go flat. Ford Motor Company recommends obeying posted speed limits.
Page 252 RWARNING Driving too fast for conditions creates the possibility of loss of vehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components. At least once a month, check the pressure in all your vehicle’s tires, including the spare.
Page 253 Front wheel bearings require periodic repacking and adjustment as specified in the Maintenance Schedule booklet. Loose or worn front wheel bearings tend to let the vehicle wander or shimmy, and can eventually cause excessive tire wear. Whenever a wheel is removed and then re-installed, always remove any corrosion that may be present on the mounting surface of the wheel and/or the surface of the hub, drum or...
Page 254 Tire Rotation Because your vehicle’s front and rear tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the following diagram. For tire rotation intervals, see the Maintenance Schedule booklet.
Page 255 If your vehicle has aluminum wheels, you may demount the full size, non-temporary spare tire (if so equipped) and remount on an aluminum wheel to rotate the spare tire into your vehicle’s rotation pattern. Rebalance the wheel. You may discover uneven outside shoulder wear on your vehicle’s front radial tires if you drive often in the city and turn frequently around curbs.
Page 256 Make sure that all replacement tires are of the same size, type, load-carrying capacity, and tread design (e.g. “All Terrain”, etc.), as originally offered by Ford. RWARNING Do not replace your tires with “high performance” tires or larger size tires.
Page 257 Tire identification chart RWARNING Use of aftermarket wheel assemblies may damage your vehicle or cause accidents resulting in serious injuries.
Page 258 Wheel and Tire Matching See an authorized tire dealer for proper servicing procedures. Wheels and tires must be properly removed, matched and remounted to maintain the best possible ride. Snow Tires and Chains The tires on your vehicle have all-weather treads that provide traction in rain or snow.
Page 259: Filling The Fuel Tank
Put the chains on tightly with the ends held down securely. Verify that no chain touches any wiring, brake lines or fuel lines. Retighten the chains after driving 1/2 mile (0.8 km). Follow the chain manufacturer’s instructions. Do not drive faster than 30 mph (48 km/h) or the chain manufacturer’s recommended speed limit, whichever is lower.
Page 260 Opening the Fuel Filler Door Fuel filler door remote release To open the fuel filler door latch, pull on the release lever located between the driver’s seat and the door. You cannot open the fuel filler door by pulling on the door itself. Fuel filler door remote release lever If the release lever is stuck or damaged and you cannot open the fuel filler door, you must use...
Page 261 Fuel filler door override handle Removing the fuel cap The proper instructions for removing the fuel cap are as follows: Unscrew the fuel cap by exerting pressure on the plastic lock bar and rotating the fuel cap counterclockwise. Turn the fuel cap 1/2 to 3/4 of a turn until a hissing sound is heard.
Page 262 the fuel cap. The ratcheting mechanism allows the fuel cap to be sealed without overtightening. If you lose the fuel cap, replace it with an authorized Motorcraft or equivalent part. RWARNING If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision.
Page 263 Choosing the Right Fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. The damage may not be covered by your warranty. Your vehicle was not designed to use fuel containing manganese-based additives such as MMT.
Page 264 Gasolines for clean air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates such as a maximum of 10% ethanol or 15% MTBE.
Page 265 Do not smoke when refueling. Fuels are extremely flammable. Do not siphon any fuel by mouth. RWARNING Gasoline or gasoline blended with methanol can cause blindness and possible death when swallowed. If any fuel is swallowed, call a physician or poison control center immediately.
Page 266 To fill the fuel tank properly: NOTE: Extinguish all lit cigarettes, other smoking materials, and any open flames before fueling your vehicle. 1. Remove the fuel cap by following the instructions above under Removing the Fuel Cap in this chapter. Proceed to add fuel to the tank only if your vehicle is on level ground.
Page 267 You may need to crank the engine several times before the fuel system starts to pump fuel from the tank to the engine. Fuel Economy Fuel economy is an estimate of the efficiency of your vehicle and can be calculated as Miles Per Gallon (MPG) or Liters Per 100 Kilometers (L/100K).
Page 268: Emission Control System
The following decrease fuel economy: Lack of regular, scheduled maintenance Excessive speed Rapid acceleration Driving with your foot on the brake Sudden stops Extended engine idling Using speed control in hilly terrain Extended use of the A/C, defroster, rear window defroster and other accessories Underinflated tires Heavy loads Aftermarket add-ons such as bike, ski or...
Page 269 RWARNING Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. RWARNING On vehicles without original equipment floor covering or insulation, do not let passengers ride in your truck in a manner that allows contact between skin and the metal floor.
Page 270 Do not drive your vehicle if it does not operate properly. See your dealer if the engine runs on for more than five seconds after you shut it off or if it misfires, surges, stalls, or backfires. Information about your vehicle’s emission control system is on the Vehicle Emission Control Information decal located on or near the engine.
Page 271 authorized service center can perform a detailed OBD II drive cycle as it would any other type of repair work. Lights and Bulb Replacement It is a good idea to check the operation of the following lights frequently: headlamps high-mount brakelamp tail lamps brakelamps hazard flasher...
Page 272 RWARNING Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. NOTE: If the bulb is accidently touched, it should be cleaned with rubbing alcohol before being used.
Page 273 NOTE: Do not disturb the aim adjusting screws. 5. Pull the headlamp away from the vehicle and remove the electrical connector by pulling rearward. 6. Unsnap the bulb retaining wire and carefully remove the bulb assembly from its socket by gently pulling it out without turning it.
Page 274 2. Snap the retaining wire over both sides of the bulb and connect the electrical connector. 3. Position the headlamp on the vehicle and install the four attaching screws. 4. Turn the headlamps on and make sure that they work properly. If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again.
Page 275 6. Apply brakes to confirm the brakelamp is functional after installing. Replacing the high-mount brakelamp bulb — liftgate models only Dual Rear Door Models To remove the brakelamp: 1. Remove the two screws from the surface of the lens. 2. Pull the lens assembly out of the lamp housing.
Page 276 3. Install the lens assembly into lamp. 4. Install and tighten the two screws. Replacing the high-mount brakelamp bulb — dual rear door models only...
Page 277 Bulb Specifications...
Page 279: Cleaning Your Vehicle
Ford, however, believes that continual improvement in customer satisfaction is a high priority. For this reason, Ford has authorized its dealers to repair, at no charge to the owner, the surfaces of new vehicles damaged by...
Page 280 NOTE: Before going to a car wash, find out if the brushes are abrasive. If you have whitewall tires that are difficult to clean with regular detergent, use Ford Extra Strength Whitewall Tire Cleaner or equivalent. Follow the directions on the container and rinse the tires with plenty of clean water.
Page 281 Cleaning the Instrument Panel Lens Clean the instrument panel lens with a soft cloth and a glass cleaner, such as Ford Ultra-Clear Spray Glass Cleaner, or equivalent. Do not use paper towel or an abrasive cleaner to clean the lens as these may cause scratches.
Page 282: Vehicle Storage
NOTE: Before using any cleaner, test it on a small, hidden area of fabric. If the fabric’s color or texture is adversely affected by a particular cleaner, do not use it. Cleaning the Built-In Child Seat (if equipped) Your Built-In Child Seat may be cleaned with mild soap and water.
Page 283 Body Wash vehicle thoroughly to remove dirt, grease, oil, tar or mud from exterior surfaces, rear wheel housing and underside of front fenders. Periodically wash vehicles stored in exposed locations. Touch-up raw or primed metal to prevent rust. Cover chrome and stainless steel parts with a thick coat of auto wax to prevent discoloration.
Page 284 Ford Gas Stabilizer should be added whenever actual or expected storage periods exceed 60 days. Follow the instructions on the label. The vehicle should then be operated at idle speed to circulate the additive throughout the fuel system. A volatile corrosion inhibitor added to the fuel system will protect the fuel system’s inner...
Page 285 Ford Accessories for Your Vehicle Ford has many fine products available from your dealer to clean your vehicle and protect its finishes. For best results, use the following, or products of equivalent quality:...
Page 286 In addition, each accessory is made from high quality materials and meets or exceeds Ford’s rigid engineering and safety specifications. That is why Ford brand accessories are warranted for up to 12 months or 12,000 miles (20,000 km), whichever comes first. See your dealer for complete warranty information and accessory availability.
Page 288 NOTE: When adding accessories, equipment, passengers, and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR, GAWR as shown on the Safety Compliance Certification Label). Consult your dealer for specific weight information.
Page 289 5 watts or less will not ordinarily affect your vehicle’s operation.) NOTE: Because we have no control over the installation, design, or manufacture of such systems, Ford cannot assume responsibility for any adverse effects or damage that may result if you use this equipment.
Page 291: Capacities And Specifications
Capacities and Specifications Refill Capacities, Motorcraft Parts, and Lubricant Specifications Motorcraft Parts...
Page 292 Fluid Specifications and Capacities...
Page 294 Lubricant Specifications...
Page 295: Engine Compartment
Engine Compartment Your vehicle has one of the following types of engines: A 3.0 Liter SEFI, V-6 engine or A 4.0 Liter SEFI, V-6 engine. The following pages show diagrams of each engine type and where to find items that you should regularly service.
Page 298 Your Vehicle Identification Number (VIN) You should include your Vehicle Identification Number (VIN) any time you write to Ford Motor Company about your vehicle. The Vehicle Identification Number is attached to your vehicle in the following places: on the metal tag attached to the top of the instrument panel on the driver’s side —...
Page 299: Reporting Safety Defects (U.s. Only)
National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 300: Customer Assistance
Customer Assistance Roadside Assistance Ford Motor Company has set up a 24-hour, seven-day-a-week hotline with trained operators who put you in touch with the help you need if you experience a problem with your vehicle. This complimentary service is provided to you throughout your warranty period of 3 years or 36,000 miles (60,000 km), whichever comes first.
Page 301 1-800-241-FORD (in Canada call 1-800-665-2006). If You Have a Service Problem Ford Motor Company has authorized Ford and Lincoln-Mercury dealerships that can service your vehicle for you. This chapter tells you how to get service or maintenance for your vehicle.
Page 302 If you are away from home when your vehicle needs to be serviced, or if you need more help than the dealer gave you, contact the Ford Customer Assistance Center to find an authorized dealership that may be able to help.
Page 303: The Dispute Settlement Board
Review? The Board reviews all warranty performance complaints on Ford, Mercury and Lincoln cars and Ford and Mercury light trucks under the new vehicle limited warranty that have not been resolved by either a dealer or Ford Motor Company, except those involving:...
Page 304 California and Wisconsin purchasers/lessees. How Does the Board Work? The Board consists of: three consumer representatives a Ford or Lincoln/Mercury dealer Consumer candidates for Board membership are recruited and trained by an independent consulting firm. Dealers are chosen because of...
Page 305 DSB’s independent administrator Your dealership and a Ford Motor Company representative are asked to submit statements at this time. To review your case properly, the Board needs...
Page 306 Board’s decision. The decisions of the Board are binding on the dealer and Ford, but not on consumers who may elect to pursue other remedies available to them under state or federal law. Decisions of the...
Page 307 Ford of Canada does not have a Dispute Settlement Board. If you have a problem that cannot be resolved by an agreement among you, Ford of Canada, and the Ford dealer, contact the Canadian Motor Vehicle Arbitration Plan (CAMVAP). In many areas of Canada, CAMVAP will help resolve the problem and, if necessary, will arrange for the matter to be arbitrated.
Page 308 Mediation/Arbitration Program (Canada Only) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 309 Use of leaded fuel in your vehicle without a proper conversion may damage the effectiveness of your emissions control system and may cause engine knocking or serious engine damage. Ford Motor Company is not responsible for any damage that is caused by use of improper fuel.
Page 310 If you are in other foreign countries, contact the nearest Ford dealership. If the dealership cannot help you, they can direct you to the appropriate Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S. or Canada,...
Page 311: Accessories
Accessories Ford Accessories for Your Vehicle Ford has many fine products available from your dealer to clean your vehicle and protect its finishes. For best results, use the following, or products of equivalent quality: A wide selection of accessories is available through your local authorized dealer.
Page 313 NOTE: When adding accessories, equipment, passengers, and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR, GAWR as shown on the Safety Compliance Certification Label). Consult your dealer for specific weight information.
Page 314 5 watts or less will not ordinarily affect your vehicle’s operation.) NOTE: Because we have no control over the installation, design, or manufacture of such systems, Ford cannot assume responsibility for any adverse effects or damage that may result if you use this equipment.
Page 326: Index
Index Accessory position on the ignition ..74 Additives, engine oil ..Air bag supplemental restraint system and child safety seats ..description .
Page 327 Autolamp system (see Headlamps) ..72 Automatic transmission fluid, adding ... . . fluid, checking ... . fluid, refill capacities .
Page 328 Brakes (continued) fluid, specifications ..front disc ....if brakes do not grip well ..master cylinder ... . new brake linings.
Page 329 Charging system gauge ..15 Charging system warning light ..13 Child safety restraints built-in child seat ... child safety belts .
Page 330 Cooling fan....Crankcase emission filter..Customer Assistance Center, Ford (U.S.). . Customer Assistance Centre, Ford of Canada..28, 44 108, 110 22, 29...
Page 331 Daytime running light system ..72 Defects, reporting ... . Defrost, rear window ... 69 Dipstick automatic transmission fluid .
Page 332 Emergency brake (parking brake) ..Emission control system catalytic converter ..emissions warranty ..Engine check engine warning light ..12 does not start .
Page 333 Entry system, illuminated ..73 Exhaust fumes ... . . Extended Service Plan, Ford ..Fan, engine fan, avoiding injury ..
Page 334 Fuel calculating fuel economy ..capacity ....choosing the right fuel ..comparisons with EPA fuel economy estimates .
Page 335 Gas cap (see Fuel cap) ..Gas mileage (see Fuel economy) . . . Gasohol ....Gasoline (see Fuel).
Page 336 Hazard flashers ... . 78, 199 Headlamps aiming ....checking alignment ..cleaning .
Page 337 Instrument panel ... . . 59 cleaning ....registers ....61 Integrated child seat (see Built-in child seat) .
Page 338 Lights, warning and indicator (continued) engine oil pressure ... 16 hazard warning light ..78, 199 high beam ....14 oil pressure .
Page 339 National Highway Traffic Safety Administration ... . New vehicle break-in ... Octane rating ....Odometer description .
Page 340 Radio (see Electronic sound systems) ..21 Rear anti-lock brakes ..description ....Rear axle lubricant specification .
Page 341 Safety restraints (continued) for adults ....for children....for infants ... . for pregnant women.
Page 342 Shoulder and lap belts (see Safety restraints) ..Shoulder belts (see Safety restraints) . . . Side mirrors adjusting....91 Snow tires and chains .
Page 343 Tail lamps bulb replacement ... cleaning ....Temperature control (see Climate control) . . 61 Tether anchor installation (see Child restraints) .
Page 344 Transmission automatic operation ..fluid, checking and adding (automatic) ... . fluid, refill capacities ..lubricant specifications .
Page 345 Warm engine, starting ..Warning chimes headlamps on....14 key in ignition ... . . 14 safety belt .
Page 346 Windshield, washing ... 76 Windshield washer fluid and wipers checking and replacing wiper blades . . operation ....76 reservoir .
Page 347: Service Station Information
Service Station Information...

This manual is also suitable for:

Aerostar

Ford 1997 Aerostar Manual

Quick Links

Related Manuals for Ford 1997 Aerostar

Summary of Contents for Ford 1997 Aerostar

This manual is also suitable for:

Table of Contents