Panasonic SC-MAX370 Operating Instructions Manual page 19

Radio
Sound is distorted.
• Use an optional FM outdoor antenna. The antenna
should be installed by a competent technician.
A beat sound is heard.
• Switch off the TV or move it away from the system.
• When in AM tuner mode, select from "BP 1" to "BP 4"
that provides the best reception.
A low hum is heard during AM broadcasts.
• Move the antenna away from other cables and cords.
Bluetooth
®
Pairing cannot be done.
• Check the Bluetooth device condition.
®
The device cannot be connected.
• The pairing of the device was unsuccessful.
Do pairing again.
• The pairing of the device has been replaced.
Do pairing again.
• This system might be connected to a different device.
Disconnect the other device and try pairing the device
again.
The device is connected but audio cannot be heard
through the system.
• For some built-in Bluetooth devices, you have to set
®
the audio output to "SC-MAX370" manually. Read the
operating instructions of the device for details.
Sound from the device is interrupted.
• The device is out of the 10 m communication range.
Move the device nearer to the system.
• Remove any obstacle between the system and the
device.
• Other devices that use the 2.4 GHz frequency band
(wireless router, microwaves, cordless phones, etc.)
are interfering. Move the device nearer to the system
and distance it from the other devices.
• Select "MODE 1" for stable communication.
The One-Touch Connection (NFC feature) is not
working.
• Make sure the unit and the NFC feature of the device
are turned on. ( 14)
Main unit displays
"USB A NO DEVICE"
"USB B NO DEVICE"
• The USB device is not connected. Examine the
connection.
"DEVICE FULL"
• You cannot do recording because the remaining
recording time of the USB device is less than the total
time of the music source.
Change to a USB device which has enough recording
time and do the recording again.
"ERROR"
• An incorrect operation was done. Read the instructions
and try again.
"ERROR" (during recording)
• You cannot select other playback source (example:
radio, USB etc.) or press [:] or [9] during
recording. Stop the recording function.
• You cannot open the disc tray when recording from an
AM source.
"F61"
• Examine and correct the speaker cords connection.
• Disconnect the USB device. Switch off the system and
then switch it on again.
"F70"
• Examine the Bluetooth device.
®
• Disconnect the Bluetooth device. Switch off the
®
system and then switch it on again.
"F77"
• Switch off the system and then switch it on again.
"NO PLAY"
"UNSUPPORT"
• Examine the content. You can only play supported
format.
• The files in the USB device can be corrupted. Format
the USB device and try again.
• The unit may have a problem. Turn the unit off and
then on again.
"NO TRACK"
• There is no album or track in the USB device or the
internal memory.
"PLAYERROR"
• You played an unsupported MP3 file. The system will
skip that track and play the next one.
"REMOTE 1"
"REMOTE 2"
• The remote control and the main unit are using
different codes. Change the code of the remote
control.
- When "REMOTE 1" is shown, press and hold [OK]
and [1] for a minimum of 4 seconds.
- When "REMOTE 2" is shown, press and hold [OK]
and [2] for a minimum of 4 seconds.
"TEMP NG"
• The temperature protection circuit has been activated,
and the system will switch off. Let the unit cool down
before switching it on again.
• Check that the ventilation opening of the unit is not
obstructed.
• Ensure this unit is well ventilated.
"USB OVER CURRENT ERROR"
• The USB device is using too much power.
Disconnect the USB device, switch off the system and
then switch on again.
"VBR"
• The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
19
19