Settins - Siemens SIPROTEC 6MU805 User Manual

A.8 Settings
Addresses which have an appended "A" can only be changed with DIGSI, under "Display Additional Settings".
The table indicates region-specific default settings. Column C (configuration) indicates the corresponding sec-
ondary nominal current of the current transformer.
Addr. Parameter
0104 OSC. FAULT REC.
0202 Vnom PRIMARY
0203 Vnom SECONDARY
0204 CT PRIMARY
0205 CT SECONDARY
0206A Vph/Vdelta
0214 Rated Frequency
0217 Ignd-CT PRIM
0218 Ignd-CT SEC
0241 Volt.trans.A:C1
0242 Volt.trans.A:C2
0243 Volt.trans.B:C1
0244 Volt.trans.B:C2
0245 Volt.trans.C:C1
0246 Volt.trans.C:C2
0247 Volt.tran.Vx:C1
0248 Volt.tran.Vx:C2
0325 Vnom sec Vx
0333 Vnom prim Vx
0352 U4 inverting
0357 SV-Stop
0369 VT Con Type
0459 SysConMUConf
0461 PhaseIndepRatio
0403 MAX. LENGTH
0404 PRE. TRIG. TIME
0405 POST REC. TIME
0406 BinIn CAPT.TIME
0407 VLAN ID
0408 VLAN Priority
0438 PPS Delay
0460 PPS Synchro
0440A Overflo Quality
0441A OutRang Quality
0442A BadRef Quality
0443A Oscill Quality
0444A Failure Quality
0445A OldData Quality
SIPROTEC, 6MU805, Manual
C53000-G1140-C380-5, Release date 06.2018
Function Setting Options
Device Configuration Disabled
Enabled
P.System Data 1 0.10 .. 800.00 kV
P.System Data 1 34 .. 400 V
P.System Data 1 10 .. 50000 A
P.System Data 1 1A
5A
P.System Data 1 1.00 .. 3.00
P.System Data 1 50 Hz
60 Hz
P.System Data 1 1 .. 50000 A
P.System Data 1 1A
5A
P.System Data 1 1.0 .. 100.0 pF
P.System Data 1 250 .. 10000 pF
P.System Data 1 1.0 .. 100.0 pF
P.System Data 1 250 .. 10000 pF
P.System Data 1 1.0 .. 100.0 pF
P.System Data 1 250 .. 10000 pF
P.System Data 1 1.0 .. 100.0 pF
P.System Data 1 250 .. 10000 pF
P.System Data 1 34 .. 230 V
P.System Data 1 0.10 .. 800.00 kV
P.System Data 1 YES
NO
Device Configuration YES
NO
Device Configuration Conventional
Cap. Volt.Meas.
Device Configuration Disabled
Enabled
Device Configuration Disabled
Enabled
Osc. Fault Rec. 0.30 .. 6.00 sec
Osc. Fault Rec. 0.05 .. 0.50 sec
Osc. Fault Rec. 0.05 .. 0.50 sec
0.10 .. 5.00 sec; 
Osc. Fault Rec.
Merging Unit 0...4095
Merging Unit 1...7
Merging Unit 0 μs, 0.1 μs...5000.00 μs
Merging Unit On
OFF
Merging Unit False
Merging Unit Set By MU
True
False
Merging Unit False
Merging Unit False
Merging Unit Set By MU
True
False
Merging Unit False
Default Setting
Disabled Oscillographic Fault Records
20.00 kV Rated Primary Voltage
100 V Rated Secondary Voltage (L-L)
400 A CT Rated Primary Current
1A CT Rated Secondary Current
1.73 Matching ratio Phase-VT To Open-Delta-VT
50 Hz Rated Frequency
400 A Ignd-CT rated primary current
1A Ignd-CT rated secondary current
10.0 pF Voltage transducer A: Capacity C1
2200 pF Voltage transducer A: Capacity C2
10.0 pF Voltage transducer B: Capacity C1
2200 pF Voltage transducer B: Capacity C2
10.0 pF Voltage transducer C: Capacity C1
2200 pF Voltage transducer C: Capacity C2
10.0 pF Voltage transducer Vx: Capacity C1
2200 pF Voltage transducer Vx: Capacity C2
100 V Rated Secondary Voltage Vx
20.00 kV Rated Primary Voltage Vx
NO U4 inverting
NO SV-Stop
Conventional Voltage Connection type
Disabled MU Configuration via IEC61850 Configurator
Disabled Phase Independent Ratio
2.00 sec Max. length of a Waveform Capture Record
0.25 sec Captured Waveform Prior to Trigger
0.10 sec Captured Waveform after Event
0.50 sec Capture Time via Binary Input
1 VLAN ID
4 VLAN Priority
0.0 μs PPS Delay
ON PPS Synchronization
False Quality bit: Overflow
Set By MU Quality bit: OutofRange
(Options True and False for test purpose)
False Quality bit: BadReference
False Quality bit: Oscillatory
Set By MU Quality bit: Failure
(Options True and False for test purpose)
False Quality bit: OldData
Appendix
A.8 Settings
Comments
141