BRP E250DHLSCS Service Manual page 395

EMM CIRCUIT/SENSOR
51 Fuel injector circuit #1 OPEN
52 Fuel injector circuit #2 OPEN
53 Fuel injector circuit #3 OPEN
54 Fuel injector circuit #4 OPEN
55 Fuel injector circuit #5 OPEN
56 Fuel injector circuit #6 OPEN
57 High RPM with low TPS setting
58 Operating temperature not reached (port)
59 Operating temperature not reached (stbd)
61 Fuel injector circuit #1 SHORTED
62 Fuel injector circuit #2 SHORTED
63 Fuel injector circuit #3 SHORTED
64 Fuel injector circuit #4 SHORTED
65 Fuel injector circuit #5 SHORTED
66 Fuel injector circuit #6 SHORTED
67 Engine Temperature Sensor circuit fault (stbd)
68 Engine Temperature BELOW range (stbd)
69 Engine Temperature ABOVE range (stbd)
71 Oil pressure circuit sensor fault detected
72 Oil pressure BELOW expected range
73 Oil pressure ABOVE expected range
74 Water pressure sensor circuit fault detected
75 Water pressure BELOW expected range
76 Water pressure ABOVE expected range
77 S.A.C. overcurrent fault
78 Analog 5V circuit overload detected
79 Starter solenoid circuit OPEN
81 Ignition timing circuit #1 OPEN
82 Ignition timing circuit #2 OPEN
83 Ignition timing circuit #3 OPEN
84 Ignition timing circuit #4 OPEN
85 Ignition timing circuit #5 OPEN
86 Ignition timing circuit #6 OPEN
87 Exhaust pressure circuit fault
88 Exhaust pressure BELOW expected range
89 Exhaust pressure ABOVE expected range
91 Fuel pump circuit OPEN
92 Exhaust valve solenoid OPEN (V4)
94 Fuel pump circuit SHORTED
97 Intermittent switched B+ detected
NOTE: Always note service codes before clearing codes. Clear stored codes using diagnostic software. Clearing some codes requires turning EMM "OFF" and then "ON" again.
page 2
Rev 01/08
DASHBOARD
EMM LED DISPLAY GAUGE WARNING
DISPLAY
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
CHECK ENGINE
LED 3: FLASHING
(FLASHING)
LED 3: OFF (Cranking) / ON (Running) -
LED 3: OFF (Cranking) / ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 3: OFF (Cranking) / ON (Running) -
LED 3: OFF (Cranking) / ON (Running) -
LED 4: ON (Running) WATER TEMP/HOT
LED 3: ON (Running) -
LED 3: ON (Running) -
LED 3: ON (Running) -
LED 3: ON (Running) -
LED 3: ON (Running) -
LED 3: ON (Running) -
LED 1: OFF (Key On) / ON (Running) -
LED 3: ON (Running) -
LED 3: OFF (Key On) / ON (Running) CHECK ENGINE
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 3: ON (Running) -
LED 3: ON (Running) -
LED 3: ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 2: ON (Running) -
LED 3: ON (Running) -
TIME TO
SENSOR: CIRCUIT VOLTAGE / RESISTANCE (Ω) / INFORMATION
ACTIVATE
10 seconds
10 seconds
10 seconds
Check injector/circuit resistance—2 to 3 Ω @ 72°F (22°C).
10 seconds
10 seconds
10 seconds
TPS < 5% and RPM > 3000. Engine SHUTDOWN. Will NOT restart until code has been cleared. The problem could be caused by
10 seconds
uncontrolled fuel entering the engine. DO NOT attempt to start the outboard until the problem has been found and repaired.
Engine temperature < 122°F (50°C) with engine speed < 1000 RPM.
10 minutes
Engine temperature < 122°F (50°C) with engine speed < 1000 RPM.
10 minutes
10 seconds
10 seconds
10 seconds
Check injector/circuit resistance—2 to 3 Ω @ 72°F (22°C).
10 seconds
10 seconds
10 seconds
Engine Temperature < -13° F (-25° C), or > 329° F (165° C).
10 seconds
Check 5 V circuit and ground (NEG), and sensor resistance—9000 to 11000 Ω @ 77°F (25°C).
10 seconds Engine Temperature < -4° F (-20° C). Check engine temperature and sensor resistance.
Engine Temperature ≥ 212°F (100°C) below 2000 RPM or ≥ 194°F (90°C) above 2000 RPM.
10 seconds
Engine limited to 1200 RPM. Check cooling system.
10 seconds
10 seconds
10 seconds
10 seconds
10 seconds
10 seconds
10 instances SAC current > 2 amps and/or < 20 V. Check for shorted 55 V wiring (injector circuits). Check for pinched or chaffed wiring.
10 seconds Sensor voltage < 4.75 V. Check sensors and related wiring. Check for pinched or chaffed wiring.
10 seconds Check starter solenoid circuit for continuity (key switch OFF) and for 12 V with key switch ON.
16 instances
16 instances
16 instances
EMM counts failed ignition events (crankshaft revolutions). Check circuit resistance.
16 instances
16 instances
16 instances
10 seconds < -85 in. water or > 85 in. water. Check for plugged or pinched hose or exhaust fitting.
10 seconds
10 seconds
Check pump/circuit resistance—2 to 3 Ω @ 77°F (25°C).
10 seconds
10 seconds
Check pump/circuit resistance—2 to 3 Ω @ 77°F (25°C).
2 seconds
10 seconds Switched battery voltage < 7 V. Check connections and wiring
Check thermostat and pressure relief valve.
Check thermostat and pressure relief valve.
< 0.15 V , > 4.85 V
< 0.4 V
> 4.6 V
< 0.15 V , > 4.85 V
< 0.4 V
> 4.6 V
< 40 in. water
> 80 in. water
Refer to exhaust valve relay tests.