Milnor 30015T6X Installation Manual
Hide thumbs
Also See for 30015T6X:
- Service manual (101 pages) ,
- Mechanical parts and service (99 pages) ,
- Installation manual (54 pages)
Related Manuals for Milnor 30015T6X
Summary of Contents for Milnor 30015T6X
- Page 1 Manual Number: MCWOTI01 Edition (ECN): 2020414 Installation 30015 and 30022 T6X, VRJ, V8Z, VZZ Rigid Washer-Extractors PELLERIN MILNOR CORPORATION Post Office Box 400, Kenner, Louisiana 70063–0400, U.S.A.
-
Page 3: Table Of Contents
• Do not let a vacuum occur...................23 • Flush the chemical tube with water..............23 • Put the chemical tube fully below the inlet............23 • Prevent leaks.......................23 3 Installation Procedures ........................24 Handling a Washer-extractor from Delivery to Final Location ..........24 Notices..........................25 Pellerin Milnor Corporation... - Page 4 Chemical Supplier Precautions..................34 4 Dimensional Drawings: 30015 and 30022 T6X - Short base (10 bolt)........35 30015T6X ..........................37 30015T6X Options ........................38 30022T6X ..........................39 30022T6X Options ........................40 5 Dimensional Drawings: 30015 and 30022 VRJ, V8Z, VZZ - Short base (10 bolt) ....41 30015VRJ ..........................43...
- Page 5 Contents Tables Table 1 Trademarks ........................6 Pellerin Milnor Corporation...
-
Page 6: General Information
1 General Information Pellerin Milnor Corporation... -
Page 7: Limited Standard Warranty
General Information BMP720097 / 19036 BRUUUM01.1 0000229985 D.2 D.6 12/5/19 11:43 AM Released Pellerin Milnor Corporation... -
Page 8: How To Get The Necessary Repair Components
Email: parts@milnor.com BNUUUU02 / 2020152A BNUUUU02 0000158094 4/6/20 2:44 PM Released Trademarks BNUUUU02.R01 0000158093 D.2 E.2 4/6/20 2:44 PM Released ® These words are trademarks of Pellerin Milnor Corporation and other entities: Table 1. Trademarks AutoSpot™ ® ® GreenFlex™ MilMetrix PulseFlow ®... -
Page 9: Safety - Rigid Washer Extractors
� cylinder. Do not operate the machine with a malfunctioning door interlock. � Know the location of all emergency stop switches, pull cords, and/or kick plates and � use them in an emergency to stop machine motion. Pellerin Milnor Corporation... -
Page 10: Safety Alert Messages-Unsafe Conditions
Do not tamper with or disable any safety device or operate the machine with a mal- � functioning safety device. Request authorized service. Pellerin Milnor Corporation... -
Page 11: Hazards Resulting From Damaged Mechanical Devices
WARNING: Multiple Hazards — Careless operator actions can kill or injure person- nel, damage or destroy the machine, damage property, and/or void the warranty. Do not tamper with or disable any safety device or operate the machine with a mal- � functioning safety device. Request authorized service. Pellerin Milnor Corporation... -
Page 12: Careless Servicing Hazards-Vital Information For Service Personnel
NOTICE: This information may apply to models in addition to those listed above. It ap- plies to paper tags. It does not apply to the vinyl or metal safety placards, which must re- main permanently affixed to the machine and replaced if no longer readable. Pellerin Milnor Corporation... - Page 13 Read the manuals before proceeding. This symbol appears on most tags. The machine ships with safety, operator, and routine maintenance guides for customer use. Milnor dealer manuals for installing, commissioning, and servicing the machine are also available from the Milnor Parts department.
-
Page 14: Installation Tag Guidelines
Read the manuals before proceeding. This symbol appears on most tags. The machine ships with safety, operator, and routine maintenance guides for customer use. Milnor dealer manuals for installing, commissioning, and servicing the machine are also available from the Milnor Parts department. - Page 15 General Information B2TAG93013: This bearing housing was lubricated at the Milnor factory before shipment. B2TAG94081: Motor must rotate in this direction. On single mo- tor washer-extractors and centrifugal extractors, the drive motor must turn in this direction during draining and extraction. This tag is usually wrapped around a motor housing.
- Page 16 B2T2003001: Hold the side of the connection stationary with a wrench as you tighten the connection with another wrench. Other- wise, you may twist components, such as valves, damaging them. B2T2004027: Steam connection. (Optional.) Pellerin Milnor Corporation...
-
Page 17: Important Installation Precautions
BNUUUF01.R02 0000109240 D.2 C.4 A.4 1/2/20 2:14 PM Released Use wiring no smaller than that listed for your machine's voltage in the “Wire size... ”column in the “External Fuse and Wire Sizes...” document. The table value applies to runs up to 50 feet (15 Pellerin Milnor Corporation... -
Page 18: Ground
100 feet (30 meters). If an inverse time circuit breaker is used and local codes require a larger wire size than that specified by Milnor, abide by the local code. NOTICE: The specified wire size may appear too small for the fuse or circuit breaker shown. -
Page 19: Major Design Considerations
Machine forces can cause damage to the machine or the floor without the correct anchorage. • Applicable building codes, even when met, do not guarantee sufficient structural support and isolation of machine forces to the laundry room. Pellerin Milnor Corporation... -
Page 20: Primary Information Sources
NOTICE: All data is subject to change without notice and may have changed since last printed. It is the responsibility of the potential owner/operator to obtain written confirma- tion that any data furnished by Milnor ® applies for the model number(s) and serial num- ber(s) of the purchased machine(s). -
Page 21: How Chemical Supplies Can Cause Damage
The company that does these procedures must make sure that these procedures do not cause dam- age. Pellerin Milnor Corporation accepts no responsibility for chemical damage to the ma- chines it makes or to the goods in a machine. -
Page 22: Figure 2 Incorrect Configurations That Let The Chemical Supply Go In The Ma
Figure 2. Incorrect Configurations That Let the Chemical Supply Go In the Machine by a Siphon Schematic Views Legend P... Pump T... Chemical tank S... The siphon occurs above here. Liquid in the gray parts of the chemical tube and tank can go in the machine. Pellerin Milnor Corporation... -
Page 23: Figure 3 Incorrect Configurations That Let The Chemical Supply Go In The Ma
Important Installation Precautions Figure 3. Incorrect Configurations That Let the Chemical Supply Go In the Machine by Gravity Schematic Views Legend P... Pump T... Chemical tank D... Chemical tube. Liquid in the gray areas can go in the machine. Pellerin Milnor Corporation... -
Page 24: Equipment And Procedures That Can Prevent Damage
— There is a manifold on the machine to attach chemical tubes from a chemical pump system. The manifold has a source of water to flush the chemical supplies with water. Figure 4. Examples of Manifolds for Chemical Tubes. Your equipment can look different. Pellerin Milnor Corporation... -
Page 25: Close The Line
BNUUUR02.R02 0000160545 D.2 E.3 B.3 1/2/20 2:14 PM Released — When you do maintenance on the chemical pump system: • Use the correct components. • Make sure that all connections are the correct fit. • Make sure that all connections are tight. Pellerin Milnor Corporation... -
Page 26: Installation Procedures
Location BNWUUI03.C01 0000254787 D.2 B.7 C.5 1/2/20 2:19 PM Released This document supersedes documents BIIFLI01, BIRUUI01, MSIN0206AE, and MSIN0301AE as of October 1, 2019. It applies to all Milnor ® washer-extractor models in production as of Octo- ber 1, 2019. -
Page 27: Notices
Disclaimer BNWUUI03.R04 0000257899 D.2 B.7 A.4 1/2/20 2:19 PM Released — Pellerin Milnor Corporation is not responsible for damage to the machine after it leaves the factory. Pellerin Milnor Corporation strongly recommends that the consignee (usually the owner/management) carefully inspect the machine in its protective wrapping before off-loading and inspect the uncovered machine after off-loading. -
Page 28: Rigger Precautions
Know and accommodate the Use lifting and moving equipment appropriate for the machine machine shipping weight. shipping weight, as shown on the Bill of Lading. To obtain the shipping weight in advance, contact the Milnor ® Transportation department. Use only lifting eyes for crane Machines designed for crane lifting are provided with lifting lifting. - Page 29 Raise the machine slightly and remove the wood blocking. In- that the hold-down force is stall a flat washer and nut on each anchor bolt and tighten in- distributed. crementally in an alternating pattern. After tightening, check each anchor at least twice. Pellerin Milnor Corporation...
-
Page 30: Technician Precautions
Check for and remove shipping tie wraps. � Check for and remove suspension hold-down hardware, if applicable. � Check for and remove red shipping brackets, if applicable. � See the “Cylinder inspection” warning and inspect the cylinder for smoothness. � Pellerin Milnor Corporation... - Page 31 Check for and remove sus- See also the service manual. Example: pension hold-down hard- ware, if applicable. Check for and remove red Shipping brackets are painted red. See the shipping brackets parts shipping brackets, if document in the service manual. applicable. Pellerin Milnor Corporation...
-
Page 32: Can The Door(S) Be Opened Before Utilities Are Connected
Connection Precautions for Washer-extractors BNWUUI04.C01 0000255071 D.2 B.4 A.6 1/2/20 2:19 PM Released This document supersedes documents BNWBUI01, BNWBUI02, BNWBUI03, BNWBUI04, BIRQVI01, BIMUUI02, and BIFUUI01. It applies to all Milnor ® washer-extractor models in pro- duction as of October 1, 2019. -
Page 33: Notices
— This document and the documents it references address common tasks that the plumber, elec- trician, and chemical supplier will perform. Other tasks, not explained here, can be needed. Infor- mation about these tasks is usually provided by the dealer, the Milnor ®... -
Page 34: Plumber Precautions
Foreign material such as debris in air lines, trapped air in water lines, and condensate in steam lines can damage machine components. Do not twist valve Hold a wrench on the valve side of a pipe connection to prevent the bodies. valve from twisting when you tighten the connection. Pellerin Milnor Corporation... -
Page 35: Electrician Precautions
Confirm the reliability of the electric service. � Confirm the machine is phased in correctly. � Confirm the correct line voltage setting on a selectable 240/208 volt machine. � Attach the stinger leg, if any, only to L3. � Pellerin Milnor Corporation... -
Page 36: Chemical Supplier Precautions
BIWUUI03 is also available at: https://milnor.sharefile.com/d-s79f12e8f11f42a9b Understand the machine The machine controller is explained in detail in the reference manual controller. for your machine, which is available from the Milnor ® Parts department. Pellerin Milnor Corporation... -
Page 37: Dimensional Drawings: 30015 And 30022 T6X - Short Base (10 Bolt)
4 Dimensional Drawings: 30015 and 30022 T6X - Short base (10 bolt) Pellerin Milnor Corporation... - Page 38 This page intentionally blank...
-
Page 43: Dimensional Drawings: 30015 And 30022 Vrj, V8Z, Vzz - Short Base (10 Bolt)
5 Dimensional Drawings: 30015 and 30022 VRJ, V8Z, VZZ - Short base (10 bolt) Pellerin Milnor Corporation... - Page 44 This page intentionally blank...
-
Page 57: Dimensional Drawings: Pedestals
6 Dimensional Drawings: Pedestals Pellerin Milnor Corporation... - Page 58 This page intentionally blank...