Milnor 30015T6X Service Manual
  1. Manuals
  2. Brands
  3. Milnor Manuals
  4. Washer
  5. 30015T6X
  6. Service manual

Milnor 30015T6X Service Manual

Hide thumbs Also See for 30015T6X:
Table of Contents

Advertisement

Quick Links

Published Manual Number/ECN: MAP30V8ZBE/2019066A
• Publishing System: TPAS2
• Access date: 02/08/2019
• Document ECNs: Latest
Service
30015T6X,VRJ,V8Z, VZZ
30022T6X,VRJ,V8Z, VZZ
Washer-Extractors
PELLERIN MILNOR CORPORATION
POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.

Advertisement

Table of Contents
loading

Related Manuals for Milnor 30015T6X

Summary of Contents for Milnor 30015T6X

  • Page 1 Published Manual Number/ECN: MAP30V8ZBE/2019066A • Publishing System: TPAS2 • Access date: 02/08/2019 • Document ECNs: Latest Service 30015T6X,VRJ,V8Z, VZZ 30022T6X,VRJ,V8Z, VZZ Washer-Extractors PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.

  • Page 3: Table Of Contents

    Drive Chart 30015T6X, 30022T6X BMP140003/2014155A Drive Chart BMP140025/2016434A Motor Mount BMP140004/2016434A 3. Cylinder, Shell and Bearing Assemblies Cylinder, Shell, Bearing and Console Installation 30015T6X & 30022T6X BMP140027/2015074B Main Bearing 30015T6X, 30022T6X BMP140026/2014155A Cylinder, Shell, Bearing and Console Installation BMP140006/2016434B Main Bearing 30015VRJ, 30022VRJ BMP120025/2014155B Main Bearing 30015V8Z, VZZ &...
  • Page 4 Drain Installation BMP110056/2014155A 3 Inch Electric Drain Valve BMP920017/2014155A 7. Control and Sensing Assemblies Vibration Safety Switch Adjustments MSSMA408BE/199273BV Vibration Safety Switch BMP140032/2014155A Level Sensing 30015T6X, 30022T6X BMP170011/2018484A Level Sensing 30015VRJ, V8Z, VZZ, 30022VRJ, V8Z, VZZ BMP100045/2018484A Temperature Probe BMP180073/2018484A...

  • Page 5: Limited Standard Warranty

    (unless the time period is specifically extended for certain parts pursuant to a specific MILNOR published extended warranty) from our factory with no operating hour limitation. This warranty is contingent upon the equipment being installed, operated and serviced as specified in the operating manual supplied with the equipment, and operated under normal conditions by competent operators.

  • Page 6: How To Get The Necessary Repair Components

    • If the component is an electrical component, give the schematic number if known. • If the component is a motor or an electrical control, give the nameplate data from the used component. To write to the Milnor factory: Pellerin Milnor Corporation Post Office Box 400...

  • Page 7: Trademarks

    BNUUUU02 / 2017285A BNUUUU02 0000158094 A.3 7/13/17 1:53 PM Released Trademarks BNUUUU02.R01 0000158093 A.2 7/13/17 1:11 PM Released These words are trademarks of Pellerin Milnor Corporation and other entities: Table 1 Trademarks AutoSpot™ GreenTurn™ Milnor® PulseFlow® CBW® GreenFlex™ MilMetrix® PurePulse®...

  • Page 8: Safety-Rigid Washer Extractors

    The owner/user must familiarize himself with the contents of all machine instruction manuals. The owner/user should direct any questions about these instructions to a Milnor® dealer or the Milnor® Service department.
  • Page 9 The Safety Guide and other machine manuals must be available at all times to the appropriate personnel. See the machine service manual for safety placard part numbers. Contact the Milnor Parts department for replacement placards or manuals. Maintenance —Ensure the machine is inspected and serviced in accordance with the norms of 1.5.
  • Page 10 Processing can cause solvent-containing goods to give off flammable vapors. • Do not use flammable solvents in processing. • Do not process goods containing flammable substances. Consult with your local fire department/public safety office and all insurance providers. PELLERIN MILNOR CORPORATION...
  • Page 11 This will over-speed the motor and pulleys and can cause them to rip apart, discharging metal fragments at high speed. • Stop the machine immediately if any of these conditions occur: • abnormal whining sound during extract • skidding sound as extract ends • clutches remain engaged or re-engage during extract PELLERIN MILNOR CORPORATION...
  • Page 12 Hazards include but are not limited to panic, burns, poisoning, suffocation, heat prostration, biological contamination, electrocution, and crushing. • Do not enter the cylinder until it has been thoroughly purged, flushed, drained, cooled, and immobilized. — End of BIUUUS27 — PELLERIN MILNOR CORPORATION...
  • Page 13 • the liquor level and chemical conditions in the bath preceding extraction, and • other miscellaneous factors. ® Estimates of the maximum force normally encountered are available for each Milnor model and ® size upon request. Floor or foundation sizes shown on any Milnor...
  • Page 14 All data is subject to change without notice and may have changed since last printed. It is the sole responsibility of every potential owner to obtain written ® confirmation that any data furnished by Milnor applies for the model(s) and serial number(s) of the specific machines.
  • Page 15 Read the manuals before proceeding. This symbol appears on most tags. The machine ships with safety, operator, and routine maintenance guides for customer use. Milnor dealer manuals for installing, commissioning, and servicing the machine are also available from the Milnor Parts department.
  • Page 16 B2T2003001: Hold the side of the connection stationary with a wrench as you tighten the connection with another wrench. Other- wise, you may twist components, such as valves, damaging them. End of document: BNWOAI02 Pellerin Milnor Corporation...
  • Page 17 Read the manuals before proceeding. This symbol appears on most tags. The machine ships with safety, operator, and routine maintenance guides for customer use. Milnor dealer manuals for installing, commissioning, and servicing the machine are also available from the Milnor Parts department.
  • Page 18 B2T2003001: Hold the side of the connection stationary with a wrench as you tighten the connection with another wrench. Other- wise, you may twist components, such as valves, damaging them. B2T2004027: Steam connection. (Optional.) End of document: BNWOAI03 Pellerin Milnor Corporation...

  • Page 19: Prevent Damage From Chemical Supplies And Chemical Systems

    The company that does these procedures must make sure that these procedures do not cause dam- age. Pellerin Milnor Corporation accepts no responsibility for chemical damage to the ma- chines it makes or to the goods in a machine.
  • Page 20 Figure 1. Incorrect Configurations That Let the Chemical Supply Go In the Machine by a Siphon Schematic Views Legend Pump Chemical tank The siphon occurs above here. Liquid in the gray parts of the chemical tube and tank can go in the machine. Pellerin Milnor Corporation...
  • Page 21 BNUUUR02.R02 0000160545 A.2 A.8 8/30/17 3:28 PM Released Use the chemical manifold supplied. There is a manifold on the machine to attach chemical tubes from a chemical pump system. The manifold has a source of water to flush the chemical supplies with water. Pellerin Milnor Corporation...
  • Page 22 Figure 4. A Configuration that Prevents Flow in the Machine When the Pump is Off (if the chemical tube and tank have no pressure) Schematic View Legend Chemical inlet on the machine Chemical tube Pump Chemical tank Pellerin Milnor Corporation...
  • Page 23 Prevent leaks. When you do maintenance on the chemical pump system: • Use the correct components. • Make sure that all connections are the correct fit. • Make sure that all connections are tight. End of document: BNUUUR02 Pellerin Milnor Corporation...
  • Page 24 BMP140008/2016434A Page (1 / 2) Safety Placards and Locations- 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ If the placard is removed or you cannot read it, replace the placard immediately. If the placard is aluminum, the mounting holes are on the machine. Use self-tapping screws. If the placard is vinyl, put the placard in the approximate location shown.
  • Page 25 Page (2 / 2) Safety Placards and Locations- 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ Parts List—Safety Placards and Locations Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 26 BMP140009/2016434A Page (1 / 2) Safety Placards and Locations- ISO 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ ISO Placards are shown on this page. If the placard is removed or you cannot read it, replace the placard immediately. If the placard is aluminum, the mounting holes are on the machine. Use self-tapping screws.
  • Page 27 Page (2 / 2) Safety Placards and Locations- ISO 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ Parts List—Safety Placards and Locations Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...

  • Page 28: Guards & Covers

    BMP140005/2018155A Page (1 / 3) Guards & Covers 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ Figure 1: Front View T6X Controls (shown) 14,15 Side Brackets Extrusion applied to these edges PELLERIN MILNOR CORPORATION...
  • Page 29 BMP140005/2018155A Page (2 / 3) Guards & Covers 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ Figure 2: Rear View 4,5,6 (4 places) Dust Cover (within) (8 places) Rear belt guard PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 30 HOLEPLUG 7/8" BLK HEYCO #2703 03 C1824Z DUST COVER=30"V#Z BELT 02 02087D EXTRUSION=30" SHORT FRAME COSMETIC 15N110H RDWASHHD TORXBOLT M6-1X25MM ZN 15G004HB EXTRUNUT M6-1 GRIP 0.8-4MM 01 10020 NPLT SMALL "MILNOR" LOGO 02 04553 SIDE COSMETIC SUPPORT BRKT 3022V8 PELLERIN MILNOR CORPORATION...

  • Page 31: 27 1. Service And Maintenance

    Service and Maintenance...

  • Page 32: Torque Requirements For Fasteners

    These tables give the standard dimension, grade, threadlocker, and torque requirements for ® fasteners frequently used on Milnor equipment. ® Note 1: Data from the Pellerin Milnor Corporation “Bolt Torque Specification” (bolt_torque_milnor.xls/2002096). Fasteners Made of Carbon Steel 1.1. Without a Threadlocker 1.1.1.
  • Page 33 Table 3: Torque Values for Plated Fasteners with Maximum 5/16-inch Diameters and No Lubricant The Grade of the Bolt Grade 2 Grade 5 Grade 8 Grade BC Dimension Pound-Inches Pound-Inches Pound-Inches Pound-Inches 1/4 x 20 1/4 x 28 5/16 x 18 5/16 x 24 PELLERIN MILNOR CORPORATION...
  • Page 34 Specific applications sometime require that a LocTite product is applied to a bolt size outside the ranges shown here. For example, Milnor specifies LocTite 242 for use on certain 1" bolt applications and has confirmed this usage with the LocTite manufacturer. You may see variances such as this in the documentation for specific machine assemblies.
  • Page 35 Table 8: Torque Values if You Apply LocTite 262 The Grade of the Bolt Grade 2 Grade 5 Grade 8 Grade BC Dimension Pound-feet Pound-feet Pound-feet Pound-feet 3/4 x 10 3/4 x 16 7/8 x 9 7/8 x 14 PELLERIN MILNOR CORPORATION...
  • Page 36 1.2. Table 11: Torque Values for Stainless Steel Fasteners 5/16-inch and Smaller 18-8 Stainless with 316 Stainless 18-8 Stainless Loctite 767 Pound-Inc Pound-Inc Pound-Inc Dimension 1/4 x 20 1/4 x 28 5/16 x 18 5/16 x 24 PELLERIN MILNOR CORPORATION...
  • Page 37 CAUTION 3 : Malfunction Hazard—Heat, vibration, or mechanical shocks can let the fasteners loosen if you do not apply the threadlocker correctly. Loose fasteners can cause malfunctions of the equipment. • Read the threadlocker manufacturer's instructions and warnings. Obey these instructions. PELLERIN MILNOR CORPORATION...
  • Page 38 No threadlocker here Apply the threadlocker to this area Nut depth Disassembly —For high-strength threadlocker, apply heat for five minutes. Disassemble with 3.3. hand tools while the parts are hot. For low-strength and moderate-strength threadlocker, disassemble with hand tools. PELLERIN MILNOR CORPORATION...
  • Page 39 Torque Requirements for Fasteners Figure 4: Disassembly Apply Heat to a Small Area Legend How to apply heat to a small fastener How to apply heat to a large fastener — End of BIUUUM04 — PELLERIN MILNOR CORPORATION...

  • Page 41: Drive Assemblies

    Drive Assemblies...

  • Page 42: Drive Chart

    BMP140003/2014155A Page (1 / 1) Drive Chart 30015T6X, 30022T6X Parts List—Drive Chart Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration.
  • Page 43 -------------------------------------------------------------------------------------------COMPONENTS------------------------------------------------------------------ 561825B2SD VPUL 2B18.25 (SD) MTO 56VB073XM2 VBELT BX73 EA=1BELT 56Q1KSD 1+1/2" BUSH VPUL QD TYPE SD 56030B2H VPUL 2B3.0/A2.6 2BK32H OR EQUAL 56Q1CH 1+1/8"BUSH VPULTYP H,D,QT OR L 15E230 STRMACHKEY 3/8SQX2+1/2 TOL.+0 15E195 SQMACHKEY 3/16X1+1/2 NOTAPER&H PELLERIN MILNOR CORPORATION...

  • Page 44: Motor Mount

    BMP140004/2016434A Page (1 / 2) Motor Mount 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ 13,14,15 (4 places) PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 45 BMP140004/2016434A Page (2 / 2) Motor Mount 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ Parts List—Motor Mount Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration.

  • Page 47: 43 3. Cylinder, Shell And Bearing Assemblies

    Cylinder, Shell and Bearing Assemblies...
  • Page 51 BMP140026/2014155A Page (1 / 3) Main Bearing 30015T6X 30022T6X Hole plug 16,17,C 11,B D,18 View A-A 4,16 Notes: A. Apply adhesive to the bolt. B. The seal holder must be fully down before you tighten the fasteners. C. Apply primer and adhesive to the rear bearing cup and holder housing.
  • Page 52 BMP140026/2014155A Page (2 / 3) Main Bearing 30015T6X 30022T6X Vent Vent Leak-off from Seals Parts List—Main Bearing Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In"...
  • Page 53 BMP140026/2014155A Page (3 / 3) Main Bearing 30015T6X 30022T6X Parts List—Main Bearing Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration.

  • Page 59: Main Bearing 30015V8Z, Vzz & 30022V8Z, Vzz

    E. Pack grease between these two seals during assembly. Item 15 is not shown. These plugs are used temporarily to prevent dirt from entering unfilled holes. 16,17 8 Places View B-B PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 60 MACH=MAIN SHAFT, 3022V8 X2 03573X MACH=BEARING 3022HS W/STARPLATE X2 03659W HOUSE=SEAL+BRG 3022V8 24S15840 SEAL SKF 15840, P#CR40X60X8 CRW1 R 54A309310 FAG 32308A(CUP&CONE)=40MM BORE, 90MM O.D.(EA=SET)1.58"ID 24S052A SEAL 2.559X3.55X.315 CR#25430 24S053 SEAL 2.625X3.625X.437#10051L5 24S053V SEAL 2.625X3.625X.437#10050H5L VITON PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 61 SHIM=.005 CRS BLUE 3022V8 02 03324D SHIM=.020 CRS WHITE 3022V8 02 03324E SHIM=.050 CRS CLEAR 3022V8 20C007H THDLK REMVBL-#24221 20C011B RETAIN CMPD ADH LCT#60905 .5CC 20C006P PRIMER-N #7649 LCT#21348-4 20C009 THRDLKSEAL LCT#27731 50CC 5N0E03ABE2 NPT NIP 1/4X3 TBE BRASS STD PELLERIN MILNOR CORPORATION...

  • Page 63: Door Assemblies

    Door Assemblies...
  • Page 64 Door Assembly and Installation BMP110049/2017036A (1 / 3) 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 1,2,3 13,14,15 13,14,15 Door Installation 23,24 25,26 Add or remove shims till the door locks properly and seals.
  • Page 65 Door Assembly and Installation BMP110049/2017036A (2 / 3) 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ Pellerin Milnor Corporation Pellerin Milnor Corporation Litho in U.S.A. P. O. Box 400, Kenner, LA 70063-0400 8,9,10,11,12 6 (See BMP130002.) 25,26 Section B-B: Door Installation Ensure that the gasket joint Section A-A: Door Installation is at top-dead-center.
  • Page 66 *SHELL CLAMP RING=30" MACHINE X2 02361G SHELLFRONT,30", FLAT FRONT 02 03261 30" DOOR FRAME MACHINED 98CMCR0971 DOOR INTERLOCK ASSY V8Z VRJ MILNOR ASSY A33 03226B 02 03228D DOOR LOCK BOX COVER 3022V8 15K052 HXCAPSCR 5/16-18UNC2AX3/4 SS18 15G188 HEXLOKNUT 5/16-18 BRASS 15U246 FLATWASHER 1"ODX25/64IDX1/8"30...

  • Page 67: Door Lock Mechanism

    Door Lock Mechanism MCR27E5, MWR27E5; 3015T6X,VRJ,V8Z,VZZ; 30022T6X,VRJ,V8Z,VZZ; MWF27J8, MWF27Z8; 30022X8R 36021V5Z, 36021V7Z, 36026V5Z, 36026V7Z, 42026V6Z, 42030V6Z Figure 1: Components DOOR LOCK SOLENOID DOOR LOCK SWITCH DETAILS A & B DETAIL C DOOR CLOSED SWITCH PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 68 SWITCH TO BE “OFF”. “ON”. AIR GAP AIR GAP DETAIL A: DETAIL B: DOOR LOCK SWITCH “OFF” DOOR LOCK SWITCH “ON” 3/16” MINIMUM CLEARANCE MEASURE THIS WHILE THE SLIDER IS DOWN. DETAIL C: DOOR CLOSED SWITCH PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 69 "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. Item Description Used In Part Number Comments --------------------------------------------------------------------------------------------------COMPONENTS------------------------------------------------------------------------------- 98CMCR0971 DOOR INTERLOCK ASSY V8Z VRJ MILNOR ASSY A33 03226B X2 03306A MACH=GAGE DR LOCK SWITH,MCR PELLERIN MILNOR CORPORATION...

  • Page 70: Door Handle And Lock Actuator

    Legend Detailed view CC. Cross Section Detailed view instances 4 Torsion spring Flange bearing Bolt Thrust washer Retainer ring Do not open the ring more than necessary to get it on the shaft. Spring Roller ball Retainer PELLERIN MILNOR CORPORATION...
  • Page 71 Tighten the nut. Put the free end of the spring into this hole. The shim with the added notch Rear view Inside view Detailed view Torsion spring The shim thickness is (.230 inches). The shim thickness is (.015 inches). PELLERIN MILNOR CORPORATION...
  • Page 72 "all" in the "Used In" column. The numbers shown in the "Item" column are those shown in the illustrations. Used In Item Part Number Description/Nomenclature Comments Components 98CMCR0925 Assembly 20C007 Adhesive 02 04192 Shim, .023 02 04192A Shim, .015 — End of BIIFBM13 — PELLERIN MILNOR CORPORATION...

  • Page 73: 69 5. Chemical Supply Devices

    Chemical Supply Devices...

  • Page 74: Soap Chute

    BMP140007/2016434A Page (1 / 2) Soap Chute 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ Figure 1: Exploded View HOUSING 13 14 10 11 Items 10,11&12 Fasten splash guard assembly to plastic housing (4 places). GASKET SHELL PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 75 BMP140007/2016434A Page (2 / 2) Soap Chute 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ Parts List—Soap Chute Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration.

  • Page 76: Peristaltic Supply Inlets

    BMP140031/2016434A Page (1 / 3) Peristaltic Supply Inlets 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ Figure 1: 30015T6X and 30022T6X 18,19 Vent 16,17 Air Space 2 1/2”(64MM) To the Shell Back Detail: Air Gap Peristaltic Supply into the Shell PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 77 BMP140031/2016434A Page (2 / 3) Peristaltic Supply Inlets 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ Figure 2: 30015 VRJ,V8Z and 30022VRJ,V8Z 11,12 18,19 Vent 16,17 Air Space 2 1/2”(64MM) To the Shell Back Detail: Air Gap Peristaltic Supply into the Shell...
  • Page 78 BMP140031/2016434A Page (3 / 3) Peristaltic Supply Inlets 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ Parts List—Peristaltic Supply Inlets Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration.

  • Page 79: Water And Steam Piping And Assemblies

    Water and Steam Piping and Assemblies...

  • Page 80: Duo-In Water Valve Assembly 30015T6X, 30022T6X

    BMP140029/2014155A Page (1 / 2) Duo-in Water Valve Assembly 30015T6X, 30022T6X Hot Water for Supply Hot and Cold Water Inlet PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 81 5N0E03KBE2 NPT NIP 1/4X3.5 TBE BRASS STD 27A0050 CLP-RGDSTL COND #PS1100-1/2 96P058A71 1/4"NPT X 1/8"ORIFICE 240V 5/6-BURKERT 51E507 HOSESTEM BRASS 1/4MPX1/2HOSEID 60E006C PVC TUBING NYL.REINF.5IDX.75OD 27A040 HOSECLAMP 7/16-25/32SS W/SCREW 96P060C71 3/4"DUO-IN 1/2"HOSE-OUT 240VHF ZYTEL NATURAL COLOR N50 PELLERIN MILNOR CORPORATION...
  • Page 82 BMP140030/2014155A Page (1 / 2) Brass Water Valves 30015VRJ, 30022VRJ 14,15 14,15 PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 83 5N0K06ABE2 NPT NIP 1/2X6 TBE BRASS STD 27A0050 CLP-RGDSTL COND #PS1100-1/2 96P057B71 1/2"NPT X 1/2"ORIFICE 240V 5/6 PARKER 51E510 HOSESTEM BRASS 1/2MPX3/4HOSEID 60E008A TUBINGNYLREINF.75"IDX1.025"OD 27A044S HOSECLAMP 11/16-1.25SSCR#64012 15P010 TRDCUT PHILPANHDSCR 10-24X1/2S 12P11AHP HOLEPLUG LPE BLACK 1" #BPF PELLERIN MILNOR CORPORATION...
  • Page 84 BMP100041/2014155A Page (1 / 2) Brass Water Valve Assembly 30015V8Z, 30022V8Z BMP140031 7,15 7,15 PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 85 5N0P06ABE2 NPT NIP 3/4X6 TBE BRASS STD 27A0050 CLP-RGDSTL COND #PS1100-1/2 96P056B71 3/4"NC 230V50/60 BURKERT #5281 51E511 HOSESTEM BRASS 3/4MP X HOSEID 60E008A TUBINGNYLREINF.75"IDX1.025"OD 12P11KSB SNAPBUSH 1.50" X 1.06" #22MP15017 12P11CSB SNAPBUSH 1.093"MH X .94"ID HEYCO#2166 60C020 RUBGRO #2802 1-5/161DX1-5/8 X1/8 60C121 GROMMET-FILLTUBE3015/22 PELLERIN MILNOR CORPORATION...

  • Page 86: Steam

    BMP160035/2016454A Page (1 / 2) Steam 30015VRJ,V8Z,VZZ 30022VRJ,V8Z,VZZ Figure 1: Steam Installation 12,13 12,13 PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 87 NPT ELBOW 90DEG 1/2" BLKMAL 15 51X017 UNIONSTRADT 1/2"#1404-8-8 60E508E09A HOSE S/S BRAID 3/8+2ENDS=9LG W2 02555 NOZZLE=STEAM INJECTION 03 11410 BRKT=STEAM MNT 30V8Z 03 11414 BRKT=STEAM INSTALL FRONT 30V8Z 27A030A UBOLT 1/2 PIPE 1/4-20 THD 15G178 1/4"-20 HEXFLANGE NUT ZINC PELLERIN MILNOR CORPORATION...

  • Page 88: Electric Heat

    BMP170013/2017426A Page (1 / 2) Electric Heat 30015 & 30022 T6X, VRJ, V8Z, VZZ * Six heating elements used in machines produced since 2016. PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 89 Description Used In Item Part Number Comments ---------------------------------------------------------------------------------------------ASSEMBLIES------------------------------------------------------------------ W2 04557A 3022VRJ/V8 SHELL WELDMENT-ELEC HEAT REFERENCE --------------------------------------------------------------------------------------------COMPONENTS------------------------------------------------------------------ 02 04585 HEATER ELEMENT GUARD 27F3000H62 HEAT ELEMENT 3000W 220V 02 04586 HEATER ELEMENT SIGHT GLASS 03 B0102 BAR:TERMINAL 6 POSITION PELLERIN MILNOR CORPORATION...

  • Page 90: Drain With Bypass

    BMP160023/2016434A Page (1 / 2) Drain with Bypass 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ Figure 1: Drain Valve Components and Installation This drain valve is in use since January 2016. For drain valves used before January 2016, see BMP110056. 2,11 9,10 9,10 PELLERIN MILNOR CORPORATION...
  • Page 91 BMP160023/2016434A Page (2 / 2) Drain with Bypass 30015T6X,VRJ,V8Z,VZZ 30022T6X,VRJ,V8Z,VZZ Parts List—Drain with Bypass Find the correct assembly first, then find the needed components. The item letters (A, B, C, etc.) assigned to assemblies are referred to in the "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration.

  • Page 92: Drain Installation

    BMP110056/2014155A Page (1 / 2) Drain Installation 30015T6X,VRJ,V8Z 30022T6X,VRJ,V8Z 16,17 9,10 16,17 9,10 9,10 11,12 PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...
  • Page 93 PRIMER CLEAR P-70 PVC (QUART) 20C052 CEMENT PVC 1/2 PINT CANS 27A074S HOSECLAMP 2+1/16-3"SSSCR#64040 60E020 FLEXHOSE 2_3/8 X 28 LG CUFF 02 03412V BKT=DUMP VAL MT 3022V8 60E303A09K HOSE 3" ID X 9-1/2 LG 27A075A T-BOLT HOSECLAMP 3.03-3.34" PELLERIN MILNOR CORPORATION...

  • Page 94: Inch Electric Drain Valve

    DRINVAL 3"N/O MTRDR240V 50/60C 96D350B71 DRINVAL 3"N/C MTRDR240V 50/60 ----------------------------------------------------------------------------COMPONENTS------------------------------------------------------------- 96D35MTR37 120V 50/60CMTR FOR 3"DRAINVAL 96D35MTR71 240V 50/60CMTR FOR 3"DRAINVAL 96D35B0D B0DY & BALL FOR 3" DRAIN VALVE 96D35C0V MTRCOVER 2-PCFOR 3"DRAINVAL 96D35PIN DRIVE PIN KIT FOR 3" DRAIN VAL PELLERIN MILNOR CORPORATION...

  • Page 95: Control And Sensing Assemblies

    Control and Sensing Assemblies...

  • Page 96: Vibration Safety Switch Adjustments

    Ê A djustments ® When the machine leaves Milnor , the actuator arm is tie-wrapped to prevent damage (except on 30015, 30020, and 30022 models). This tie wrap must be removed after the machine is set into position but before the machine is op- erated.
  • Page 97 that it has reset. In the released position the arm should rest lightly but definitely against the stop on the micro-switch case that prevents any further arm movement to the left. For machines with rigid mounted shells, where the machine is bolted to a very substantial foundation, very little machine movement will occur for a given degree of out-of-balance.

  • Page 98: Vibration Safety Switch

    * ASSY-VIBRATION SWT=LG CONTR ----------------------------------------------------------------------------COMPONENTS------------------------------------------------------------- 02 02038 PLATE INSULATING SMALL9NOV51 15P008 TRDCUT PANHD 6-32X1 NIKSTL +WA 02 15119 BRACKET=VIBSW CAD 09R020 SWITCH NC VIBR#WZ-2RW84429-P52 03 01059 VIBSWITCH CLAMP CADSTL 03 01058 VIBSWITCH WEIGHT-CADSTL 15P101 TRDCUT-F PANHD 8-32X3/8 NIKSTL PELLERIN MILNOR CORPORATION...

  • Page 99: Bmp170011/2018484A

    BMP170011/2018484A Page (1 / 2) Level Sensing 30015T6X, 30022T6X 12 (6 Places) PELLERIN MILNOR CORPORATION PELLERIN MILNOR CORPORATION...

  • Page 100: Bmp100045/2018484A

    NPT NIP 1/2X5 TBE GALSTL SK 40 5SR0K0ENF NPT RED 1/2X1/4 GALMAL 150# 51E502B HOSESTEM BRASS 1/4MPX1/8HOSEID 51E502D HOSESTEM BRASS 1/4"MPX X 3/16"HOSE ID 27A047A HOSE CLAMP 5/16" NOMINIAL MIN .256", 60E004NT TUBING (NYL.)CLR.1/4"ODX1/8" 60E004NA TUBING CLEAR PVC 3/16"IDX5/16"OD PELLERIN MILNOR CORPORATION...

  • Page 101: Bmp180073/2018484A

    "Used In" column to identify which components belong to an assembly. The item numbers (1, 2, 3, etc.) assigned to components relate the parts list to the illustration. Description Used In Item Part Number Comments -------------------------------------------------------------------------------------------COMPONENTS------------------------------------------------------------------------ 30R0043PB TEMPERATURE PROBE ASSY=BRASS PELLERIN MILNOR CORPORATION...

This manual is also suitable for:

30015t6vrj30015t6v8z30015t6vzz30022t6vrj30022t6vzz30022t6v8z ... Show all

Table of Contents