Safety Information - Pentair Pentek Intellidrive PID10 Installation And Operation Manual

SAFETY INFORMATION

SAVE THESE INSTRUCTIONS: This manual contains important instructions
that should be followed during installation, operation, and maintenance of the
product.
SAFETY SYMBOLS
This is the safety alert symbol. When you see this symbol on your pump
or in this manual, look for one of the following signal words and be alert to the
potential for personal injury:
warns about hazards that will cause serious personal injury,
death or major property damage if ignored.
warns about hazards that can cause serious personal injury,
death or major property damage if ignored.
warns about hazards that will or can cause minor personal
injury or property damage if ignored.
The word NOTE indicates special instructions that are important but not related
to hazards.
CALIFORNIA PROPOSITION 65 WARNING
This product and related accessories contain chemicals
known to the State of California to cause cancer, birth defects or other
reproductive harm.
IMPORTANT SAFETY INSTRUCTIONS
Risk of high-voltage electrical shock from EMI/RFI filter
inside. Can shock, burn or kill if the front cover of the Pentair Pentek Intellidrive ®
Constant Pressure Pump Controller is open or removed while power is
connected to the Intellidrive or the Intellidrive is running. The front cover of the
Intellidrive must be closed during operation.

Make all wiring connections, then close and fasten the cover before turning
on power to Intellidrive.

NEVER open the box when power is connected to Intellidrive.

Before doing any service or maintenance inside Intellidrive or when
connecting or disconnecting any wires inside Intellidrive:
1. DISCONNECT power.
2. WAIT 5 minutes for retained voltage to discharge.
3. Open box.

Before starting any wiring or inspection procedures, check for residual
voltage with a voltage tester.

NEVER connect power wiring to Intellidrive before mounting the box.

NEVER handle or service Intellidrive with wet or damp hands. Always make
sure hands are dry before working on Intellidrive.

NEVER reach into or change the cooling fan while power is applied to
Intellidrive.

NEVER touch the printed circuit board when power is applied to Intellidrive.
Risk of fire. Can cause severe injury, property damage or
death if installed with incorrect or inadequate circuit breaker protection.
To ensure protection in the event of an internal fault in the Pentek Intellidrive, install
the Intellidrive on an independent branch circuit protected by a circuit breaker (see
Table 2 for circuit-breaker sizing), with no other appliances on the circuit.
PN957 (25-06-20)
Risk of burns. The Intellidrive can become hot during normal
operation. Allow it to cool for 5 minutes after shut-down and before handling it to
avoid burns.
NOTE: To avoid damage to Intellidrive or problems with Intellidrive:

Connect output cables to 3-wire 1-phase and 3-phase submersible motors
as follows:
1. Red to R, Yellow to Y, Black to B.
2. Any other order will reverse the motor rotation (3-phase) and may
damage the motor.

Connect output cables to 2-wire 1-phase submersible motors as follows:
1. Connect to Y and B only.
2. Connect Ground to green screw.

Above ground 3-phase motors may have different lead colors. Generally
connect output leads as follows:
1. R to L1, Y to L2, B to L3.
2. Verify rotation after startup.

Do not modify equipment.

Do not use power factor correction capacitors as they will damage both
motor and Pentek Intellidrive.

Do not remove any parts unless instructed to do so in Owner's Manual.

Do not use a magnetic contactor on Intellidrive for frequent starting/
stopping.

Do not install or operate Intellidrive if it is damaged or parts are missing.

Before starting Intellidrive that has been in storage, always inspect it and
test operation.

Do not carry out a megger (insulation resistance) test on the control circuit
of the Intellidrive.

Do not allow loose foreign objects which can conduct electricity (such as
screws and metal fragments) inside Intellidrive box at any time. Do not
allow flammable substances (such as oil) inside Intellidrive box at any time.

Ground Intellidrive according to the requirements of the National Electrical
Code Section 250, IEC 536 Class 1, or the Canadian Electrical Code (as
applicable) , and any other codes and ordinances that apply.

All installation, service work, and inspections must be done by qualified
electrician.
EMI/RFI Filter
Risk of electric shock. Can shock, burn or kill.



Fan
Intellidrive's internal components
retain high voltage for up to 5 minutes
after input power is disconnected.
EMI/RFI Filter carries high voltage when
pump is running.
Disconnect power and wait 5 minutes
before opening Pentek Intellidrive
cover.
6020 0609
3