Available Accessories; Repairs; Environmental Protection; Trouble Shooting - Metabo ELEKTRA BECKUM Multi 260 S Operating Instructions Manual

12. Available Accessories

For special tasks the following accesso-
ries are available at your specialized
dealer – see back cover for illustrations:
A Drilling and Morticing Attachment
for drilling mortices of max. 100 mm
depth and max. 100 mm long.
B Table Extension
required for working long stock.
C Sliding Carriage Side Extension
required to work wide stock.
D Stock Stop
required for repetitive cut-off work.
E Tenoning Table
required for unproblematic tenon-
ing.
F Curved Moulding Stop
required for the exact guiding of
curved stock.
G HS Cutter Knives
260x20x2.5
for extended edge life. Resharpen-
able.
H TCT Saw Blade
250x3.2/2.2x30 24 ATB
for rip and crosscuts in grown tim-
ber and particle board.
I TCT Saw Blade
250x3.2/2.2x30 48 UAT
for rip and cross cuts in panels,
plastics, aluminium and high-quality
veneered sheets.
J TCT Saw Blade
250x3.2/2.2x30 60
ATB
General purpose saw blade for
plastics and non-ferrous metals.
K TCT Saw Blade
250x3.2/2.2x30 80 trapezoidal flat
teeth
General purpose saw blade for
plastics and non-ferrous metals.
L Ball Transfer Stand
for exact guiding of long stock.
Used with either swivel ball or roller
head.
M WAXILIT Anti-seize Compound
improves stock gliding quality on
the planing beds.
N Care and Maintenance Spray
to remove resin residue and for pre-
serving the metal surfaces.

13. Repairs

Danger!
Repairs to electric tools must
be carried out by qualified electrici-
ans only!
Electric tools in need of repair can be
sent to the service centre of your coun-
try. Refer to the spare parts list for the
address.
Please attach a description of the fault to
the electric tool.

14. Environmental Protection

The machine's packaging can be 100 %
recycled.
Worn out machines and accessories
contain considerable amounts of valua-
ble raw and plastic materials, which can
be recycled.
These instructions are printed on chlo-
rine-free bleached paper.

15. Trouble Shooting

Danger!
Prior to any servicing:
− Switch Off.
− Unplug.
− Wait until machine has come to a
complete stop.
Check to see that all safety devices are
operational after any servicing.

15.1 All operating modes

Motor does not run
No supply voltage.
− Check cables, plug, outlet and
mains fuse.
Access door not closed.
− Close access door.
ON/OFF switch locked.
− Unlock ON/OFF switch by turning
clockwise.
combination
Undervoltage relay tripped by tempo-
rary voltage failure.
− Start again.
Motor has overheated, e.g. due to blunt
cutting
buildup.
− Remove cause for overheating and
allow to cool down for approx. 10
minutes, then start again.

15.2 Surface/thickness planer

Performance lessens
Cutter knives blunt.
− Install sharp knives.
Flat belt slips.
− Re-tension flat belt.
Planed surface not smooth
Cutter knives blunt.
− Install sharp knives.
Cutter knives blocked by chips.
− Remove chips.
Moisture contents of workpiece too high.
− Dry workpiece.
Planed surface cracked
Cutter knives blunt.
− Install sharp knives.
tools, overloading or
Cutter knives blocked by chips.
− Remove chips.
Workpiece was planed against the grain.
− Plane workpiece in opposite direc-
tion.
Too much material removed in one pass.
− Make several passes at less depth
of cut.
Worked surface uneven
Cutter knives are installed unequal.
− Adjust cutter knives with setting
gauge.
Feed rate too little (thicknessing)
Resin buildup on thicknesser bed.
− Clean thicknesser bed and apply
light coat of anti-seize compound.
Feed rollers stiff.
− Repair feed rollers.
Flat belt slips.
− Re-tension flat belt.
Workpiece jams
(thicknessing)
Too much material removed in one pass.
− Make several passes at less depth
of cut.

15.3 circular saw

Loss of cutting performance
Saw blade blunt (possibly tempering
marks on blade body)
− Replace saw blade.
Flat belt slips.
− Re-tension flat belt.
chip
Sliding carriage stiff:
Guide elements dirty.
− Clean guide elements with brush,
compressed air or dust collector.

15.4 Spindle moulder

Performance lessens
Cutter blunt.
− Replace cutter.
Flat belt slips.
− Re-tension flat belt.
Blocked dust port
No dust collector hooked up:
− connect dust collector.
Dust build-up around the cutter spindle.
− Remove table insert rings, move
cutter spindle up and down and
clean surroundings with brush or
compressed air and dust collector.
Sliding carriage stiff:
Guide elements dirty.
− Clean and lubricate guide elements.
ENGLISH
31