Operation With The Drilling And Morticing Attachment (Optional Accessory); Circular Saw Mode; Setup - Metabo ELEKTRA BECKUM Multi 260 S Operating Instructions Manual

with a suitable cleaning and mainte-
nance spray (optional accessory).
•
Apply an anti-seize compound to all
planing bed surfaces afterwards.
This makes feeding easier and pro-
vides for a smoother surface finish.
8. Operation With The Drill-
ing And Morticing Attach-
ment (Optional Acces-
sory)
Note:
Further information on installation
and operation is found in the operating
instructions supplied with the Drilling and
Morticing Attachment.
Danger!
Before setting the machine up:
− Switch machine OFF.
− Unplug.
− Wait until machine has come to a
complete stop.
Flat belt change
For operation with the Drilling and Mor-
ticing Attachment the flat belt (45) must
be put on as illustrated:
45
If this is not the case, the flat belt must
be positioned as detailed in chapter
"Surface Planer Mode".
Caution!
When using the Drilling and
Morticing Attachment the speed of
the chuck must be selected accor-
ding to the mortising bit diameter!
The speed is set by changing the flat
belt:
•
small (= rear) motor pulley (48):
spindle speed 3900 min
for mortising bits 10 mm ∅ and up
•
large (= front) motor pulley (49):
spindle speed 6300 min
for mortising bits up to 10 mm ∅
To adjust the speed:
1. Open the access door.
2. Loosen lock lever (46) and lift motor
slightly with handle (47).
3. Shfit motor along the axis of the
motorshaft: The motor pulley must
be in alignment with the cutter-
block's pulley
.
48
49
4. Tighten flat belt by pushing the
motor downward with handle (47).
5. Lock motor in position with the lock
lever (46).
6. Close access door.
Adjusting the cutterblock cover:
7. Adjust cutterblock cover (50) so that
the cutterblock is completely cov-
ered.
50

9. Circular Saw Mode

9.1

Setup

Danger!
Before setting the machine up:
46
− Switch machine OFF.
− Unplug.
− Wait until machine has come to a
47
complete stop.
Flat belt change
For operation as circular saw the flat belt
(51) must be positioned as illustrated:
55
-1
If this is not the case, position it as fol-
-1
lows.
1. Open the access door.
2. Loosen lock lever (52) and lift motor
slightly with handle (53).
3. Take the flat belt that is not required
off the motor pulley (54).
4. Tuck the flat belts not required (55)
behind the retaining springs as illus-
51
52
54
53
ENGLISH
trated, so they do not interfere with
the drive belt on the pulleys.
5. Place the flat belt for the saw spin-
dle on the large diameter (front) (51)
motor pulley (54).
6. Shift motor along the axis of the
motor shaft fully to the rear: The
large diameter motor pulley must be
in alignment with the pulley on the
saw spindle.
7. Tighten the flat belt by pushing the
motor downward with the handle
(53).
8. Lock motor in position with the lock
lever (52).
9. Close access door.
Work area preparation
Ensure the removal of all not required
objects from the work area:
1. Cutter fence completely
mounted?
2. Cutter spindle fully retracted and
covered by table rings and insert?
3. Cutterblock cover lowered on the
table?
4. Suction port disconnected from the
dust collector and lowered?
Raising the saw blade
1. Remove table insert (56).
2. To raise the saw blade loosen lock
lever (57) and push lever (58) down-
ward. To lock blade at desired depth
of cut tighten lock lever (57) again.
56
58
dis-
57
25