Symbols Used Throughout These Instructions; Special Product Features; Transportation And Installation; Machine Installation - Metabo ELEKTRA BECKUM Multi 260 S Operating Instructions Manual

ENGLISH
Cutting hazard, even with the
cutting tool at standstill!
Wear gloves when changing cutting
tools.
Risk of kickback (workpiece is
caught by the saw blade and thrown
against the operator):
Always work with a properly set riving
knife.
Do not jam workpieces.
Cut thin or thin-walled workpieces only
with fine-toothed saw blades. Always
use sharp saw blades.
If in doubt, check workpiece for inclusion
of foreign matter (e.g. nails or screws).
Drawing-in/trapping hazard!
Ensure that no parts of the body or cloth-
ing ca be caught and drawn in by rotat-
ing components (no neckties, no loose-
fitting clothes; contain long hair with hair-
net).
Hazard generated by insuffi-
cient personal protection gear!
Wear hearing protection.
Wear safety glasses.
Wear dust mask if work generates dust.
Wear suitable work clothes. When work-
ing outdoors wearing of non-slip shoes is
recommended.
Risk of injury by inhaling wood
dust:
Dust of certain timber species (e.g. oak,
beech, ash) can cause cancer when
inhaled: Always use a dust collector. The
dust collector must meet the following
requirements:
− fitting the outer diameter of the suc-
tion port;
− air volume ≥ 550 m
3
/h;
− vacuum at suction port of machine
≥ 740 Pa;
− air speed at suction port of machine
≥ 20 m/s.
Hazard generated by modifica-
tion of the machine or use of
parts not tested and approved
by the equipment manufactu-
rer!
Assemble electric tool in strict accord-
ance with these instructions.
Use only parts approved by the equip-
ment manufacturer.
Do not make changes to any of the
parts.
Use only cutting tools according to
EN 847-1.
Use only matching saw blades and riving
knives.
Hazard generated by electric
tool defects!
20
Keep electric tool and accessories in
good repair. Observe the maintenance
instructions.
Check electric tool for possible damage
before any use: Before operating the
electric tool all safety devices, protection
devices or slightly damaged parts must
be inspected for proper functioning as
specified. Check to see that all moving
parts work properly and do not jam. All
parts must be correctly installed and
meet all conditions necessary for the
proper operation of the electric tool.
Damaged protection devices or parts
must be repaired or replaced by an qual-
ified specialist. Have damaged switches
replaced by a service centre. Do not
operate electric tool if the switch can not
be turned ON or OFF.
Keep handles free of oil and grease.
2.3 Symbols used through-
out these instructions
Danger!
Indicates risk of
injury or severe
damage.
Risk of electric shock!
Risk of personal injury by elec-
tric shock.
Danger! Drawing-in/trapping
hazard!
Risk of personal injury by body
parts or clothing being drawn
into the rotating saw blade.
Caution!
Risk of material damage
Note:
Supplementary information

3. Special Product Features

•
One machine – four operating
modes:
− surface planer
− thicknesser
− circular saw
− spindle moulder
•
Wide range of accessories.
•
Latest technology for perfect per-
formance.
4. Transportation and
Installation
4.1

Machine installation

1. Transport combination machine on
the pallet to a suitable location:
− space required:
min. 3 m x 4 m
Depending on workpiece dimen-
sions more space
required.
− sufficient load bearing capacity
− level
− even
− dry
− non-slip.
2. Remove packing and enclosed parts
– do not yet remove the transport
brace inside the combination
machine!
3. Unscrew and remove the metal
clamps holding the combination
machine on the pallet.
4. Extend transport handle (1) fully.
5. Hold combination machine with sev-
eral persons at the transport handle
and the opposite table edge (2) and
lift it off the pallet.
Caution!
Lift machine only at both
marked spots (1) and (2) . Other com-
ponents are not designed for the ten-
sile load by the machine weight.
2
personal
material
6. Open the access door.
7. Loosen lock lever (3) and lift motor
up.
8. While the motor is lifted up tighten
the lock lever.
9. Remove transport brace from under
the motor.
10. Close access door.
4.2

Wheel installation

1. Lift combination machine on one
side with the transport handle (1)
and place a wooden block under the
lifted
machine.
Danger!
As long as the machine is kept
in this tilted position, it must be kept
may be
from falling over by another person!
2. Put plastic protection covers over
both lifted feet of the machine.
1
3
side of the combination