Table of Contents
Advertisement
en
ENGLISH
Original Instructions
1. Declaration of Conformity
We, being solely responsible, hereby declare that
these cordless tappers / cordless drills/drivers,
identified by type and serial number *1), meet all
relevant requirements of directives *2) and
standards *3). Technical documents at *4) -
Fig. K+L.
For UK only:
We as manufacturer and authorized person to
compile the technical file, see *4)
hereby declare under sole responsibility that these
cordless tappers / cordless drills/drivers, identified
by type and serial number *1)
relevant provisions of following UK Regulations S.I.
2016/1091, S.I. 2008/1597, S.I. 2012/3032 and
Designated Standards EN 62841-1:2015, EN
62841-2-1:2018, EN 62841-2-2:2014, EN IEC
63000:2018.
2. Specified Use
The cordless tapper / cordless drills/drivers are
suitable for drilling in metal, wood, plastic and
similar materials, and also for screwdriving and
cutting internal threads.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.
3. General Safety Instructions
For your own protection and for the
protection of your power tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Read the operating
instructions to reduce the risk of injury.
WARNING – Read all safety warnings,
instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Always include these documents when passing on
your power tool.
4. Special Safety Instructions
Use the additional handle supplied with the
tool. Loss of control can cause personal injury.
Brace the power tool properly before use. This
tool produces a high output torque and without
properly bracing the tool during operation, loss of
control may occur resulting in personal injury.
12
Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden
wiring. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
Safety instructions when using long drill bits:
a) Never operate at higher speed than the
maximum speed rating of the drill bit. At higher
speeds, the bit is likely to bend if allowed to rotate
freely without contacting the workpiece, resulting in
Fig. L,
personal injury.
b) Always start drilling at low speed and with
the bit tip in contact with the workpiece. At
Fig. K, fulfill all
higher speeds, the bit is likely to bend if allowed to
rotate freely without contacting the workpiece,
resulting in personal injury.
c) Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend causing breakage and loss of control,
resulting in personal injury.
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes (e.g.
using a metal detector).
Always hold the machine with both hands on the
designated handles, take a secure stance and
concentrate on the work.
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch or short circuit battery pack contacts!
and comes into contact with your eyes, wash them
with clean water and seek medical attention
immediately!
If the machine is defective, remove the battery pack
from the machine.
Remove the battery pack from the machine before
making any adjustments, changing tools,
maintaining or cleaning.
Make sure that the tool is switched off before fitting
the battery pack.
Keep hands away from the rotating tool!
Remove chips and similar material only when the
machine is at a standstill.
Secure the workpiece to prevent slipping or rotation
(e.g. by securing with screw clamps).
WARNING – Always wear protective
goggles.
Protect battery packs from water and
moisture!
Do not expose battery packs to fire!
A slightly acidic, flammable fluid may leak
from defective Li-ion battery packs!
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
Advertisement
Table of Contents
