Declaration Of Conformity; Specified Use; General Safety Instructions; Special Safety Instructions - Metabo BFE 9-20 Original Instructions Manual

en ENGLISH
Original instructions

1. Declaration of Conformity

We declare under our sole responsibility: These
band files, identified by type and serial number *1),
comply with all relevant requirements of the
directives *2) and standards *3). Technical file at *4)
- see page 3.
For UK only:
We as manufacturer and authorized person to
compile the technical file, see *4) on page 3,
hereby declare under sole responsibility that these
band files, identified by type and serial number *1)
on page 3, fulfill all relevant provisions of following
UK Regulations S.I. 2016/1091, S.I. 2008/1597, S.I.
2012/3032 and Designated Standards EN 62841-
1:2015, EN 62841-2-4:2014, EN IEC 63000:2018 .

2. Specified Use

The band file is used for dry sanding, deburring and
polishing metals, wood, materials similar to wood,
plastics and construction materials.
The user bears sole responsibility for any damage
caused by improper use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.

3. General Safety Instructions

For your own protection and for the
protection of your electrical tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating instruc-
tions will reduce the risk of injury.
WARNING – Read all safety warnings,
instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference. Pass on your electrical tool only
together with these documents.

4. Special Safety Instructions

Hold the power tool by insulated gripping
surfaces, because the sanding surface may
contact its own cord. Cutting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
Flying sparks are created when sanding metal.
Ensure that no persons are in danger. Due to the
risk of fire, all combustible materials must be
removed from the work area (area affected by flying
sparks).
8
During machining, of metals in
particular, conductive dust can form
deposits inside the machine. This can lead to the
transfer of electrical energy onto the machine
housing. This can mean a temporary danger of
electric shocks. This is why it is necessary when the
machine is running to blow compressed air through
the rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
We recommend using a stationary extractor system
and connecting a residual current circuit-breaker
(FI) upstream. When the machine is shut down via
the FI circuit-breaker, it must be checked and
cleaned. See chapter 8. Cleaning for more
information on cleaning the motor.
Wear ear protectors. Exposure to noise can cause
hearing loss.
Wear protective gloves.
Always wear protective goggles.
Secure the workpiece against slipping, e.g. with the
help of clamping devices.
Always guide the machine with both hands on the
handles provided. Loss of control can cause
personal injury.
Never place your hand near rotating parts of the
device or near the rotating sanding belt.
Remove sanding dust and similar material only
when the machine is not in operation.
Pull the plug out of the plug socket before any
adjustments, conversions or servicing are
performed.
The rated speed of the sanding belt must be at least
equal to the belt speed in idling marked on the
power tool. A sanding belt running faster than its
rated speed can break and fly apart.
Check prior to each use that the sanding belt is
correctly attached and is completely on the rollers.
Carry out a trial run: Allow the machine to run at
idling speed for 30 seconds in a safe location. Stop
immediately if significant vibrations occur or if other
defects are noted. If such a situation occurs, check
the machine to determine the cause.
Reduce dust exposure:
Particles generated when working with this
machine may contain substances that can
cause cancer, allergic reactions, respiratory
diseases, birth defects or other propagation
defects. Some of these substances include: Lead
(in paint containing lead), mineral dust (from bricks,
concrete etc.), additives used for wood treatment
(chromate, wood preservatives), some wood types
(such as oak or beech dust), metals, asbestos.
The risk depends on for how long the user or nearby
persons are exposed to the substance.
This dust must not be allowed to enter your body.
Do the following to reduce exposure to these
substances: Ensure good ventilation of the