Zoom MRS-1044 Operation Manual page 100

Effect type/parameter list
Explanation of MODULATION/DELAY MODULE parameters
Parameter name Range
DEPTH 0 – 10
RATE
1 – 30
MIX 0 – 30
FB TYPE = FLANGER : -10 – 10
TYPE = DELAY : 0 – 10
POSITION AF / bF
COLOR
0 – 10
CLIP
FREQ
TYPE = PDL-WAH : 1 – 50
TYPE = EXCITER : 1 – 5
LEVEL
RTM OFF / On
FLT TYPE bPF / LPF
RESO
SENS -10 – 10
SHIFT
-12.0 – 24.0
TONE
BALANCE
LowBoost
SIZE
TIME TYPE = WIDE : 1 – 64
TYPE = DELAY : 1 – 50
WET LVL
DRY LVL
I MIC ALGORITHM
COMP/LIM MODULE
TYPE PARAMETER 1
SINGLE SENS
A mono input/output compressor.
COMP x1
SINGLE THRSHOLD
A mono input/output limiter.
LIMIITx1
DUAL SENS_1
A two-channel input/output compressor. Parameters for left and right can be set independently.
COMP x2
DUAL THRSH_1
A two-channel input/output limiter. Parameters for left and right can be set independently.
LIMIITx2
Explanation of COMP/LIM MODULE parameters
Parameter name
SENS SINGLE
SENS 1 DUAL ( Lch )
SENS 2
DUAL ( Rch )
ATTACK SINGLE
ATTACK_1
DUAL ( Lch )
ATTACK_2 DUAL ( Rch )
THRSHLD
SINGLE
THRSH_1 DUAL ( Lch )
THRES_2 DUAL ( Rch )
RELEASE
SINGLE
RELEASE1 DUAL ( Lch )
RELEASE2
DUAL ( Rch )
LEVEL SINGLE
LEVEL_1
DUAL ( Lch )
LEVEL_2 DUAL ( Rch )
MIC PRE MODULE
TYPE PARAMETER 1
COLOR
MIC PRE (*1)
A pre-amp for use with an external mic.
COLOR 1
MIC PRE (*2)
A pre-amp for use with an external mic.
*1: When a SINGLE type effect is selected for the COMP/LIM module
*2: When a DUAL type effect is selected for the COMP/LIM module
100
Adjusts the depth of the effect.
Adjusts the speed of the effect.
Adjusts the mix amount of the effect.
Adjusts the amount of feedback.
Exchanges the effect locations of the DRIVE module and MOD module.
1 – 4
Changes the type of the phase tone.
Emphasizes the effect.
Specifies the center frequency of the wah.
Specifies the frequency.
Sets the output level of the module.
1 – 8
Specifies whether the expression pedal will be used as a wah pedal.
Specifies the type of filter.
Adds character to the sound.
1 – 10
Adjusts the sensitivity with which the effect is applied.
Sets the amount of shift produced by the pitch shifter.
Adjust the tone.
0 – 10
Adjusts the balance between the direct sound and effect sound.
0 – 30
Emphasizes the low-frequency range.
0 – 10
Specifies the spatial width.
1 – 10
Sets the delay time.
Adjusts the mix amount of the effect sound.
0 – 30
Adjusts the mix amount of the direct sound.
0 – 30
PARAMETER 2 PARAMETER 3
ATTACK
RELEASE
ATTACK_1
RELEASE1
Range
0 – 15
0 – 15
0 – 15
0 – 15
1 – 8
PARAMETER 2 PARAMETER 3
TONE
TONE 1
Explanation of parameter
PARAMETER 4
LEVEL --
LEVEL --
LEVEL_1 SENS_2
LEVEL_1 THRES_2
Explanation of parameter
Adjusts the input sensitivity of compression.
Adjusts the speed at which compression is applied.
Adjusts the sensitivity at which the limiter begins to apply.
Specifies the length from when the input signal level falls below the threshold until
compression ends.
Specifies the output level of the module.
PARAMETER 4
LEVEL DE-ESSER
LEVEL 1 COLOR 2
PARAMETER 5 PARAMETER 6
-- --
-- --
ATTACK_2 LEVEL_2
RELEASE2 LEVEL_2
PARAMETER 5 PARAMETER 6
-- --
TONE 2 LEVEL 2
ZOOM MRS-1044